blob: 06b2e22b8b557e32ef813ae68d42c38e08c7225b (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
|
/*
* ANT Stack
*
* Copyright 2011 Dynastream Innovations
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
/*******************************************************************************\
*
* FILE NAME: ant_driver_defines.h
*
* BRIEF:
* This file defines ANT specific HCI values used by the ANT chip for a
* Qualcomm UART implementation.
*
*
\*******************************************************************************/
#ifndef __VFS_PRERELEASE_H
#define __VFS_PRERELEASE_H
// Packets may be prefixed with an optional packet type byte when being sent to
// the chip. Will not be present in messages received.
// -----------------------------------------
// | Header | Data | Footer |
// |----------------------|-----------------|
// |Optional| Data | Opt. | ... | Optional |
// | Opcode | Size | Sync | | Checksum |
// Data may include any number of ANT packets, with no sync byte or checksum.
// A read from the driver may return any number of ANT HCI packets.
// ---------------------- REQUIRED
// Which chip is this library being built for:
#define ANT_CHIP_NAME "Qualcomm UART"
// Set the file name the driver creates for the ANT device:
// If chip uses separate command and data paths:
// #define ANT_COMMANDS_DEVICE_NAME "/dev/X"
// #define ANT_DATA_DEVICE_NAME "/dev/Y"
// OR
// If chip uses one path:
#define ANT_DEVICE_NAME "/dev/ttyHS0"
// Optional Packet prefix byte.
#define HCI_PACKET_TYPE_SIZE 1
// Set to the number of bytes of header is for Opcode:
#define ANT_HCI_OPCODE_SIZE 0
// Set to the number of bytes of header is for Data Size:
#define ANT_HCI_SIZE_SIZE 1
// Set to the number of bytes of header is for Sync:
#define ANT_HCI_SYNC_SIZE 0
// Set to the number of bytes of footer is for Checksum:
#define ANT_HCI_CHECKSUM_SIZE 0
// ---------------------- OPTIONAL
// If hard reset is supported, define ANT_IOCTL_RESET
// #define ANT_IOCTL_RESET _IOW('U', 210, int)
// #define ANT_IOCTL_RESET_PARAMETER (0)
// If the chip sends flow control messages:
// Define the Opcode for a Flow Control message:
#define ANT_MESG_FLOW_CONTROL ((ANT_U8)0xC9)
// AND
// define the message content:
// That signals Flow Go:
#define ANT_FLOW_GO ((ANT_U8)0x00)
// That signals Flow Stop:
#define ANT_FLOW_STOP ((ANT_U8)0x80)
// Define protocol byte to be added
// as multiple data will be sent/received over
// same transport(BT, ANT ..etc)
// needed for HCI_PACKET_TYPE_SIZE > 1.
#define ANT_CMD_TYPE_PACKET ((ANT_U8)0x0C)
#define ANT_DATA_TYPE_PACKET ((ANT_U8)0x0E)
#endif /* ifndef __VFS_PRERELEASE_H */
|
