1 files changed, 98 insertions, 0 deletions
diff --git a/src/bt-vendor_vfs/qualcomm/uart/ant_driver_defines.h b/src/bt-vendor_vfs/qualcomm/uart/ant_driver_defines.h
new file mode 100644
index 0000000..06b2e22
--- /dev/null
+++ b/src/bt-vendor_vfs/qualcomm/uart/ant_driver_defines.h
@@ -0,0 +1,98 @@
+/*
+ * ANT Stack
+ *
+ * Copyright 2011 Dynastream Innovations
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+/*******************************************************************************\
+*
+*   FILE NAME:    ant_driver_defines.h
+*
+*   BRIEF:
+*      This file defines ANT specific HCI values used by the ANT chip for a
+*      Qualcomm UART implementation.
+*
+*
+\*******************************************************************************/
+
+#ifndef __VFS_PRERELEASE_H
+#define __VFS_PRERELEASE_H
+
+// Packets may be prefixed with an optional packet type byte when being sent to
+// the chip. Will not be present in messages received.
+
+// -----------------------------------------
+// |         Header       | Data |  Footer  |
+// |----------------------|-----------------|
+// |Optional| Data | Opt. | ...  | Optional |
+// | Opcode | Size | Sync |      | Checksum |
+
+// Data may include any number of ANT packets, with no sync byte or checksum.
+// A read from the driver may return any number of ANT HCI packets.
+
+
+// ---------------------- REQUIRED
+
+// Which chip is this library being built for:
+#define ANT_CHIP_NAME                        "Qualcomm UART"
+
+// Set the file name the driver creates for the ANT device:
+//   If chip uses separate command and data paths:
+// #define ANT_COMMANDS_DEVICE_NAME             "/dev/X"
+// #define ANT_DATA_DEVICE_NAME                 "/dev/Y"
+// OR
+//   If chip uses one path:
+
+#define ANT_DEVICE_NAME                          "/dev/ttyHS0"
+
+// Optional Packet prefix byte.
+#define HCI_PACKET_TYPE_SIZE                 1
+
+// Set to the number of bytes of header is for Opcode:
+#define ANT_HCI_OPCODE_SIZE                  0
+
+// Set to the number of bytes of header is for Data Size:
+#define ANT_HCI_SIZE_SIZE                    1
+
+// Set to the number of bytes of header is for Sync:
+#define ANT_HCI_SYNC_SIZE                    0
+
+// Set to the number of bytes of footer is for Checksum:
+#define ANT_HCI_CHECKSUM_SIZE                0
+
+// ---------------------- OPTIONAL
+
+// If hard reset is supported, define ANT_IOCTL_RESET
+// #define ANT_IOCTL_RESET                      _IOW('U', 210, int)
+// #define ANT_IOCTL_RESET_PARAMETER            (0)
+
+// If the chip sends flow control messages:
+//  Define the Opcode for a Flow Control message:
+#define ANT_MESG_FLOW_CONTROL                ((ANT_U8)0xC9)
+// AND
+//   define the message content:
+//     That signals Flow Go:
+#define ANT_FLOW_GO                          ((ANT_U8)0x00)
+
+//     That signals Flow Stop:
+#define ANT_FLOW_STOP                        ((ANT_U8)0x80)
+
+// Define protocol byte to be added
+// as multiple data will be sent/received over
+// same transport(BT, ANT ..etc)
+// needed for HCI_PACKET_TYPE_SIZE > 1.
+#define ANT_CMD_TYPE_PACKET                  ((ANT_U8)0x0C)
+#define ANT_DATA_TYPE_PACKET                 ((ANT_U8)0x0E)
+
+#endif /* ifndef __VFS_PRERELEASE_H */