Merge linux-2.6 with linux-acpi-2.6

31 files changed, 1251 insertions, 282 deletions

diff --git a/Documentation/DocBook/mcabook.tmpl b/Documentation/DocBook/mcabook.tmpl
index 4367f4642f3..42a760cd746 100644
--- a/Documentation/DocBook/mcabook.tmpl
+++ b/Documentation/DocBook/mcabook.tmpl
@@ -96,7 +96,7 @@
 
   <chapter id="pubfunctions">
      <title>Public Functions Provided</title>
-!Earch/i386/kernel/mca.c
+!Edrivers/mca/mca-legacy.c
   </chapter>
 
   <chapter id="dmafunctions">
diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt
index 84d3d4d10c1..bf1cf98d2a2 100644
--- a/Documentation/IPMI.txt
+++ b/Documentation/IPMI.txt
@@ -605,12 +605,13 @@ is in the ipmi_poweroff module.  When the system requests a powerdown,
 it will send the proper IPMI commands to do this.  This is supported on
 several platforms.
 
-There is a module parameter named "poweroff_control" that may either be zero
-(do a power down) or 2 (do a power cycle, power the system off, then power
-it on in a few seconds).  Setting ipmi_poweroff.poweroff_control=x will do
-the same thing on the kernel command line.  The parameter is also available
-via the proc filesystem in /proc/ipmi/poweroff_control.  Note that if the
-system does not support power cycling, it will always to the power off.
+There is a module parameter named "poweroff_powercycle" that may
+either be zero (do a power down) or non-zero (do a power cycle, power
+the system off, then power it on in a few seconds).  Setting
+ipmi_poweroff.poweroff_control=x will do the same thing on the kernel
+command line.  The parameter is also available via the proc filesystem
+in /proc/sys/dev/ipmi/poweroff_powercycle.  Note that if the system
+does not support power cycling, it will always do the power off.
 
 Note that if you have ACPI enabled, the system will prefer using ACPI to
 power off.
diff --git a/Documentation/RCU/NMI-RCU.txt b/Documentation/RCU/NMI-RCU.txt
new file mode 100644
index 00000000000..d0634a5c344
--- /dev/null
+++ b/Documentation/RCU/NMI-RCU.txt
@@ -0,0 +1,112 @@
+Using RCU to Protect Dynamic NMI Handlers
+
+
+Although RCU is usually used to protect read-mostly data structures,
+it is possible to use RCU to provide dynamic non-maskable interrupt
+handlers, as well as dynamic irq handlers.  This document describes
+how to do this, drawing loosely from Zwane Mwaikambo's NMI-timer
+work in "arch/i386/oprofile/nmi_timer_int.c" and in
+"arch/i386/kernel/traps.c".
+
+The relevant pieces of code are listed below, each followed by a
+brief explanation.
+
+	static int dummy_nmi_callback(struct pt_regs *regs, int cpu)
+	{
+		return 0;
+	}
+
+The dummy_nmi_callback() function is a "dummy" NMI handler that does
+nothing, but returns zero, thus saying that it did nothing, allowing
+the NMI handler to take the default machine-specific action.
+
+	static nmi_callback_t nmi_callback = dummy_nmi_callback;
+
+This nmi_callback variable is a global function pointer to the current
+NMI handler.
+
+	fastcall void do_nmi(struct pt_regs * regs, long error_code)
+	{
+		int cpu;
+
+		nmi_enter();
+
+		cpu = smp_processor_id();
+		++nmi_count(cpu);
+
+		if (!rcu_dereference(nmi_callback)(regs, cpu))
+			default_do_nmi(regs);
+
+		nmi_exit();
+	}
+
+The do_nmi() function processes each NMI.  It first disables preemption
+in the same way that a hardware irq would, then increments the per-CPU
+count of NMIs.  It then invokes the NMI handler stored in the nmi_callback
+function pointer.  If this handler returns zero, do_nmi() invokes the
+default_do_nmi() function to handle a machine-specific NMI.  Finally,
+preemption is restored.
+
+Strictly speaking, rcu_dereference() is not needed, since this code runs
+only on i386, which does not need rcu_dereference() anyway.  However,
+it is a good documentation aid, particularly for anyone attempting to
+do something similar on Alpha.
+
+Quick Quiz:  Why might the rcu_dereference() be necessary on Alpha,
+	     given that the code referenced by the pointer is read-only?
+
+
+Back to the discussion of NMI and RCU...
+
+	void set_nmi_callback(nmi_callback_t callback)
+	{
+		rcu_assign_pointer(nmi_callback, callback);
+	}
+
+The set_nmi_callback() function registers an NMI handler.  Note that any
+data that is to be used by the callback must be initialized up -before-
+the call to set_nmi_callback().  On architectures that do not order
+writes, the rcu_assign_pointer() ensures that the NMI handler sees the
+initialized values.
+
+	void unset_nmi_callback(void)
+	{
+		rcu_assign_pointer(nmi_callback, dummy_nmi_callback);
+	}
+
+This function unregisters an NMI handler, restoring the original
+dummy_nmi_handler().  However, there may well be an NMI handler
+currently executing on some other CPU.  We therefore cannot free
+up any data structures used by the old NMI handler until execution
+of it completes on all other CPUs.
+
+One way to accomplish this is via synchronize_sched(), perhaps as
+follows:
+
+	unset_nmi_callback();
+	synchronize_sched();
+	kfree(my_nmi_data);
+
+This works because synchronize_sched() blocks until all CPUs complete
+any preemption-disabled segments of code that they were executing.
+Since NMI handlers disable preemption, synchronize_sched() is guaranteed
+not to return until all ongoing NMI handlers exit.  It is therefore safe
+to free up the handler's data as soon as synchronize_sched() returns.
+
+
+Answer to Quick Quiz
+
+	Why might the rcu_dereference() be necessary on Alpha, given
+	that the code referenced by the pointer is read-only?
+
+	Answer: The caller to set_nmi_callback() might well have
+		initialized some data that is to be used by the
+		new NMI handler.  In this case, the rcu_dereference()
+		would be needed, because otherwise a CPU that received
+		an NMI just after the new handler was set might see
+		the pointer to the new NMI handler, but the old
+		pre-initialized version of the handler's data.
+
+		More important, the rcu_dereference() makes it clear
+		to someone reading the code that the pointer is being
+		protected by RCU.
diff --git a/Documentation/cdrom/sonycd535 b/Documentation/cdrom/sonycd535
index 59581a4b302..b81e109970a 100644
--- a/Documentation/cdrom/sonycd535
+++ b/Documentation/cdrom/sonycd535
@@ -68,7 +68,8 @@ it a better device citizen.  Further thanks to Joel Katz
 Porfiri Claudio <C.Porfiri@nisms.tei.ericsson.se> for patches
 to make the driver work with the older CDU-510/515 series, and
 Heiko Eissfeldt <heiko@colossus.escape.de> for pointing out that
-the verify_area() checks were ignoring the results of said checks.
+the verify_area() checks were ignoring the results of said checks
+(note: verify_area() has since been replaced by access_ok()).
 
 (Acknowledgments from Ron Jeppesen in the 0.3 release:)
 Thanks to Corey Minyard who wrote the original CDU-31A driver on which
diff --git a/Documentation/cpusets.txt b/Documentation/cpusets.txt
index ad944c06031..47f4114fbf5 100644
--- a/Documentation/cpusets.txt
+++ b/Documentation/cpusets.txt
@@ -60,6 +60,18 @@ all of the cpus in the system. This removes any overhead due to
 load balancing code trying to pull tasks outside of the cpu exclusive
 cpuset only to be prevented by the tasks' cpus_allowed mask.
 
+A cpuset that is mem_exclusive restricts kernel allocations for
+page, buffer and other data commonly shared by the kernel across
+multiple users.  All cpusets, whether mem_exclusive or not, restrict
+allocations of memory for user space.  This enables configuring a
+system so that several independent jobs can share common kernel
+data, such as file system pages, while isolating each jobs user
+allocation in its own cpuset.  To do this, construct a large
+mem_exclusive cpuset to hold all the jobs, and construct child,
+non-mem_exclusive cpusets for each individual job.  Only a small
+amount of typical kernel memory, such as requests from interrupt
+handlers, is allowed to be taken outside even a mem_exclusive cpuset.
+
 User level code may create and destroy cpusets by name in the cpuset
 virtual file system, manage the attributes and permissions of these
 cpusets and which CPUs and Memory Nodes are assigned to each cpuset,
diff --git a/Documentation/crypto/api-intro.txt b/Documentation/crypto/api-intro.txt
index a2d5b490077..74dffc68ff9 100644
--- a/Documentation/crypto/api-intro.txt
+++ b/Documentation/crypto/api-intro.txt
@@ -223,6 +223,7 @@ CAST5 algorithm contributors:
 
 TEA/XTEA algorithm contributors:
   Aaron Grothe
+  Michael Ringe
 
 Khazad algorithm contributors:
   Aaron Grothe
diff --git a/Documentation/dcdbas.txt b/Documentation/dcdbas.txt
new file mode 100644
index 00000000000..e1c52e2dc36
--- /dev/null
+++ b/Documentation/dcdbas.txt
@@ -0,0 +1,91 @@
+Overview
+
+The Dell Systems Management Base Driver provides a sysfs interface for
+systems management software such as Dell OpenManage to perform system
+management interrupts and host control actions (system power cycle or
+power off after OS shutdown) on certain Dell systems.
+
+Dell OpenManage requires this driver on the following Dell PowerEdge systems:
+300, 1300, 1400, 400SC, 500SC, 1500SC, 1550, 600SC, 1600SC, 650, 1655MC,
+700, and 750.  Other Dell software such as the open source libsmbios project
+is expected to make use of this driver, and it may include the use of this
+driver on other Dell systems.
+
+The Dell libsmbios project aims towards providing access to as much BIOS
+information as possible.  See http://linux.dell.com/libsmbios/main/ for
+more information about the libsmbios project.
+
+
+System Management Interrupt
+
+On some Dell systems, systems management software must access certain
+management information via a system management interrupt (SMI).  The SMI data
+buffer must reside in 32-bit address space, and the physical address of the
+buffer is required for the SMI.  The driver maintains the memory required for
+the SMI and provides a way for the application to generate the SMI.
+The driver creates the following sysfs entries for systems management
+software to perform these system management interrupts:
+
+/sys/devices/platform/dcdbas/smi_data
+/sys/devices/platform/dcdbas/smi_data_buf_phys_addr
+/sys/devices/platform/dcdbas/smi_data_buf_size
+/sys/devices/platform/dcdbas/smi_request
+
+Systems management software must perform the following steps to execute
+a SMI using this driver:
+
+1) Lock smi_data.
+2) Write system management command to smi_data.
+3) Write "1" to smi_request to generate a calling interface SMI or
+   "2" to generate a raw SMI.
+4) Read system management command response from smi_data.
+5) Unlock smi_data.
+
+
+Host Control Action
+
+Dell OpenManage supports a host control feature that allows the administrator
+to perform a power cycle or power off of the system after the OS has finished
+shutting down.  On some Dell systems, this host control feature requires that
+a driver perform a SMI after the OS has finished shutting down.
+
+The driver creates the following sysfs entries for systems management software
+to schedule the driver to perform a power cycle or power off host control
+action after the system has finished shutting down:
+
+/sys/devices/platform/dcdbas/host_control_action
+/sys/devices/platform/dcdbas/host_control_smi_type
+/sys/devices/platform/dcdbas/host_control_on_shutdown
+
+Dell OpenManage performs the following steps to execute a power cycle or
+power off host control action using this driver:
+
+1) Write host control action to be performed to host_control_action.
+2) Write type of SMI that driver needs to perform to host_control_smi_type.
+3) Write "1" to host_control_on_shutdown to enable host control action.
+4) Initiate OS shutdown.
+   (Driver will perform host control SMI when it is notified that the OS
+   has finished shutting down.)
+
+
+Host Control SMI Type
+
+The following table shows the value to write to host_control_smi_type to
+perform a power cycle or power off host control action:
+
+PowerEdge System    Host Control SMI Type
+----------------    ---------------------
+      300             HC_SMITYPE_TYPE1
+     1300             HC_SMITYPE_TYPE1
+     1400             HC_SMITYPE_TYPE2
+      500SC           HC_SMITYPE_TYPE2
+     1500SC           HC_SMITYPE_TYPE2
+     1550             HC_SMITYPE_TYPE2
+      600SC           HC_SMITYPE_TYPE2
+     1600SC           HC_SMITYPE_TYPE2
+      650             HC_SMITYPE_TYPE2
+     1655MC           HC_SMITYPE_TYPE2
+      700             HC_SMITYPE_TYPE3
+      750             HC_SMITYPE_TYPE3
+
+
diff --git a/Documentation/dell_rbu.txt b/Documentation/dell_rbu.txt
new file mode 100644
index 00000000000..bcfa5c35036
--- /dev/null
+++ b/Documentation/dell_rbu.txt
@@ -0,0 +1,74 @@
+Purpose:
+Demonstrate the usage of the new open sourced rbu (Remote BIOS Update) driver
+for updating BIOS images on Dell servers and desktops.
+
+Scope:
+This document discusses the functionality of the rbu driver only.
+It does not cover the support needed from aplications to enable the BIOS to
+update itself with the image downloaded in to the memory.
+
+Overview:
+This driver works with Dell OpenManage or Dell Update Packages for updating
+the BIOS on Dell servers (starting from servers sold since 1999), desktops
+and notebooks (starting from those sold in 2005).
+Please go to  http://support.dell.com register and you can find info on
+OpenManage and Dell Update packages (DUP).
+
+Dell_RBU driver supports BIOS update using the monilothic image and packetized
+image methods. In case of moniolithic the driver allocates a contiguous chunk
+of physical pages having the BIOS image. In case of packetized the app
+using the driver breaks the image in to packets of fixed sizes and the driver
+would place each packet in contiguous physical memory. The driver also
+maintains a link list of packets for reading them back.
+If the dell_rbu driver is unloaded all the allocated memory is freed.
+
+The rbu driver needs to have an application which will inform the BIOS to
+enable the update in the next system reboot.
+
+The user should not unload the rbu driver after downloading the BIOS image
+or updating.
+
+The driver load creates the following directories under the /sys file system.
+/sys/class/firmware/dell_rbu/loading
+/sys/class/firmware/dell_rbu/data
+/sys/devices/platform/dell_rbu/image_type
+/sys/devices/platform/dell_rbu/data
+
+The driver supports two types of update mechanism; monolithic and packetized.
+These update mechanism depends upon the BIOS currently running on the system.
+Most of the Dell systems support a monolithic update where the BIOS image is
+copied to a single contiguous block of physical memory.
+In case of packet mechanism the single memory can be broken in smaller chuks
+of contiguous memory and the BIOS image is scattered in these packets.
+
+By default the driver uses monolithic memory for the update type. This can be
+changed to contiguous during the driver load time by specifying the load
+parameter image_type=packet.  This can also be changed later as below
+echo packet > /sys/devices/platform/dell_rbu/image_type
+
+Do the steps below to download the BIOS image.
+1) echo 1 > /sys/class/firmware/dell_rbu/loading
+2) cp bios_image.hdr /sys/class/firmware/dell_rbu/data
+3) echo 0 > /sys/class/firmware/dell_rbu/loading
+
+The /sys/class/firmware/dell_rbu/ entries will remain till the following is
+done.
+echo -1 > /sys/class/firmware/dell_rbu/loading
+
+Until this step is completed the drivr cannot be unloaded.
+
+Also the driver provides /sys/devices/platform/dell_rbu/data readonly file to
+read back the image downloaded. This is useful in case of packet update
+mechanism where the above steps 1,2,3 will repeated for every packet.
+By reading the /sys/devices/platform/dell_rbu/data file all packet data
+downloaded can be verified in a single file.
+The packets are arranged in this file one after the other in a FIFO order.
+
+NOTE:
+This driver requires a patch for firmware_class.c which has the addition
+of request_firmware_nowait_nohotplug function to wortk
+Also after updating the BIOS image an user mdoe application neeeds to execute
+code which message the BIOS update request to the BIOS. So on the next reboot
+the BIOS knows about the new image downloaded and it updates it self.
+Also don't unload the rbu drive if the image has to be updated.
+
diff --git a/Documentation/dvb/bt8xx.txt b/Documentation/dvb/bt8xx.txt
index e6b8d05bc08..4b8c326c6aa 100644
--- a/Documentation/dvb/bt8xx.txt
+++ b/Documentation/dvb/bt8xx.txt
@@ -16,7 +16,7 @@ Enable the following options:
 "Device drivers" => "Multimedia devices"
  => "Video For Linux" => "BT848 Video For Linux"
 "Device drivers" => "Multimedia devices" => "Digital Video Broadcasting Devices"
- => "DVB for Linux" "DVB Core Support" "Nebula/Pinnacle PCTV/TwinHan PCI Cards"
+ => "DVB for Linux" "DVB Core Support" "BT8xx based PCI cards"
 
 3) Loading Modules, described by two approaches
 ===============================================
diff --git a/Documentation/exception.txt b/Documentation/exception.txt
index f1d436993eb..3cb39ade290 100644
--- a/Documentation/exception.txt
+++ b/Documentation/exception.txt
@@ -7,7 +7,7 @@ To protect itself the kernel has to verify this address.
 
 In older versions of Linux this was done with the 
 int verify_area(int type, const void * addr, unsigned long size) 
-function.
+function (which has since been replaced by access_ok()).
 
 This function verified that the memory area starting at address 
 addr and of size size was accessible for the operation specified 
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index 0665cb12bd6..2e0a01b21fe 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -51,14 +51,6 @@ Who:	Adrian Bunk <bunk@stusta.de>
 
 ---------------------------
 
-What:	register_ioctl32_conversion() / unregister_ioctl32_conversion()
-When:	April 2005
-Why:	Replaced by ->compat_ioctl in file_operations and other method
-	vecors.
-Who:	Andi Kleen <ak@muc.de>, Christoph Hellwig <hch@lst.de>
-
----------------------------
-
 What:	RCU API moves to EXPORT_SYMBOL_GPL
 When:	April 2006
 Files:	include/linux/rcupdate.h, kernel/rcupdate.c
@@ -74,14 +66,6 @@ Who:	Paul E. McKenney <paulmck@us.ibm.com>
 
 ---------------------------
 
-What:	remove verify_area()
-When:	July 2006
-Files:	Various uaccess.h headers.
-Why:	Deprecated and redundant. access_ok() should be used instead.
-Who:	Jesper Juhl <juhl-lkml@dif.dk>
-
----------------------------
-
 What:	IEEE1394 Audio and Music Data Transmission Protocol driver,
 	Connection Management Procedures driver
 When:	November 2005
@@ -102,16 +86,6 @@ Who:	Jody McIntyre <scjody@steamballoon.com>
 
 ---------------------------
 
-What:	register_serial/unregister_serial
-When:	September 2005
-Why:	This interface does not allow serial ports to be registered against
-	a struct device, and as such does not allow correct power management
-	of such ports.  8250-based ports should use serial8250_register_port
-	and serial8250_unregister_port, or platform devices instead.
-Who:	Russell King <rmk@arm.linux.org.uk>
-
----------------------------
-
 What:	i2c sysfs name change: in1_ref, vid deprecated in favour of cpu0_vid
 When:	November 2005
 Files:	drivers/i2c/chips/adm1025.c, drivers/i2c/chips/adm1026.c
diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt
index 6c98f2bd421..5024ba7a592 100644
--- a/Documentation/filesystems/proc.txt
+++ b/Documentation/filesystems/proc.txt
@@ -133,6 +133,7 @@ Table 1-1: Process specific entries in /proc
  statm   Process memory status information              
  status  Process status in human readable form          
  wchan   If CONFIG_KALLSYMS is set, a pre-decoded wchan
+ smaps	 Extension based on maps, presenting the rss size for each mapped file
 ..............................................................................
 
 For example, to get the status information of a process, all you have to do is
diff --git a/Documentation/filesystems/relayfs.txt b/Documentation/filesystems/relayfs.txt
new file mode 100644
index 00000000000..d24e1b0d4f3
--- /dev/null
+++ b/Documentation/filesystems/relayfs.txt
@@ -0,0 +1,362 @@
+
+relayfs - a high-speed data relay filesystem
+============================================
+
+relayfs is a filesystem designed to provide an efficient mechanism for
+tools and facilities to relay large and potentially sustained streams
+of data from kernel space to user space.
+
+The main abstraction of relayfs is the 'channel'.  A channel consists
+of a set of per-cpu kernel buffers each represented by a file in the
+relayfs filesystem.  Kernel clients write into a channel using
+efficient write functions which automatically log to the current cpu's
+channel buffer.  User space applications mmap() the per-cpu files and
+retrieve the data as it becomes available.
+
+The format of the data logged into the channel buffers is completely
+up to the relayfs client; relayfs does however provide hooks which
+allow clients to impose some stucture on the buffer data.  Nor does
+relayfs implement any form of data filtering - this also is left to
+the client.  The purpose is to keep relayfs as simple as possible.
+
+This document provides an overview of the relayfs API.  The details of
+the function parameters are documented along with the functions in the
+filesystem code - please see that for details.
+
+Semantics
+=========
+
+Each relayfs channel has one buffer per CPU, each buffer has one or
+more sub-buffers. Messages are written to the first sub-buffer until
+it is too full to contain a new message, in which case it it is
+written to the next (if available).  Messages are never split across
+sub-buffers.  At this point, userspace can be notified so it empties
+the first sub-buffer, while the kernel continues writing to the next.
+
+When notified that a sub-buffer is full, the kernel knows how many
+bytes of it are padding i.e. unused.  Userspace can use this knowledge
+to copy only valid data.
+
+After copying it, userspace can notify the kernel that a sub-buffer
+has been consumed.
+
+relayfs can operate in a mode where it will overwrite data not yet
+collected by userspace, and not wait for it to consume it.
+
+relayfs itself does not provide for communication of such data between
+userspace and kernel, allowing the kernel side to remain simple and not
+impose a single interface on userspace. It does provide a separate
+helper though, described below.
+
+klog, relay-app & librelay
+==========================
+
+relayfs itself is ready to use, but to make things easier, two
+additional systems are provided.  klog is a simple wrapper to make
+writing formatted text or raw data to a channel simpler, regardless of
+whether a channel to write into exists or not, or whether relayfs is
+compiled into the kernel or is configured as a module.  relay-app is
+the kernel counterpart of userspace librelay.c, combined these two
+files provide glue to easily stream data to disk, without having to
+bother with housekeeping.  klog and relay-app can be used together,
+with klog providing high-level logging functions to the kernel and
+relay-app taking care of kernel-user control and disk-logging chores.
+
+It is possible to use relayfs without relay-app & librelay, but you'll
+have to implement communication between userspace and kernel, allowing
+both to convey the state of buffers (full, empty, amount of padding).
+
+klog, relay-app and librelay can be found in the relay-apps tarball on
+http://relayfs.sourceforge.net
+
+The relayfs user space API
+==========================
+
+relayfs implements basic file operations for user space access to
+relayfs channel buffer data.  Here are the file operations that are
+available and some comments regarding their behavior:
+
+open()	 enables user to open an _existing_ buffer.
+
+mmap()	 results in channel buffer being mapped into the caller's
+	 memory space. Note that you can't do a partial mmap - you must
+	 map the entire file, which is NRBUF * SUBBUFSIZE.
+
+read()	 read the contents of a channel buffer.  The bytes read are
+	 'consumed' by the reader i.e. they won't be available again
+	 to subsequent reads.  If the channel is being used in
+	 no-overwrite mode (the default), it can be read at any time
+	 even if there's an active kernel writer.  If the channel is
+	 being used in overwrite mode and there are active channel
+	 writers, results may be unpredictable - users should make
+	 sure that all logging to the channel has ended before using
+	 read() with overwrite mode.
+
+poll()	 POLLIN/POLLRDNORM/POLLERR supported.  User applications are
+	 notified when sub-buffer boundaries are crossed.
+
+close() decrements the channel buffer's refcount.  When the refcount
+	reaches 0 i.e. when no process or kernel client has the buffer
+	open, the channel buffer is freed.
+
+
+In order for a user application to make use of relayfs files, the
+relayfs filesystem must be mounted.  For example,
+
+	mount -t relayfs relayfs /mnt/relay
+
+NOTE:	relayfs doesn't need to be mounted for kernel clients to create
+	or use channels - it only needs to be mounted when user space
+	applications need access to the buffer data.
+
+
+The relayfs kernel API
+======================
+
+Here's a summary of the API relayfs provides to in-kernel clients:
+
+
+  channel management functions:
+
+    relay_open(base_filename, parent, subbuf_size, n_subbufs,
+               callbacks)
+    relay_close(chan)
+    relay_flush(chan)
+    relay_reset(chan)
+    relayfs_create_dir(name, parent)
+    relayfs_remove_dir(dentry)
+
+  channel management typically called on instigation of userspace:
+
+    relay_subbufs_consumed(chan, cpu, subbufs_consumed)
+
+  write functions:
+
+    relay_write(chan, data, length)
+    __relay_write(chan, data, length)
+    relay_reserve(chan, length)
+
+  callbacks:
+
+    subbuf_start(buf, subbuf, prev_subbuf, prev_padding)
+    buf_mapped(buf, filp)
+    buf_unmapped(buf, filp)
+
+  helper functions:
+
+    relay_buf_full(buf)
+    subbuf_start_reserve(buf, length)
+
+
+Creating a channel
+------------------
+
+relay_open() is used to create a channel, along with its per-cpu
+channel buffers.  Each channel buffer will have an associated file
+created for it in the relayfs filesystem, which can be opened and
+mmapped from user space if desired.  The files are named
+basename0...basenameN-1 where N is the number of online cpus, and by
+default will be created in the root of the filesystem.  If you want a
+directory structure to contain your relayfs files, you can create it
+with relayfs_create_dir() and pass the parent directory to
+relay_open().  Clients are responsible for cleaning up any directory
+structure they create when the channel is closed - use
+relayfs_remove_dir() for that.
+
+The total size of each per-cpu buffer is calculated by multiplying the
+number of sub-buffers by the sub-buffer size passed into relay_open().
+The idea behind sub-buffers is that they're basically an extension of
+double-buffering to N buffers, and they also allow applications to
+easily implement random-access-on-buffer-boundary schemes, which can
+be important for some high-volume applications.  The number and size
+of sub-buffers is completely dependent on the application and even for
+the same application, different conditions will warrant different
+values for these parameters at different times.  Typically, the right
+values to use are best decided after some experimentation; in general,
+though, it's safe to assume that having only 1 sub-buffer is a bad
+idea - you're guaranteed to either overwrite data or lose events
+depending on the channel mode being used.
+
+Channel 'modes'
+---------------
+
+relayfs channels can be used in either of two modes - 'overwrite' or
+'no-overwrite'.  The mode is entirely determined by the implementation
+of the subbuf_start() callback, as described below.  In 'overwrite'
+mode, also known as 'flight recorder' mode, writes continuously cycle
+around the buffer and will never fail, but will unconditionally
+overwrite old data regardless of whether it's actually been consumed.
+In no-overwrite mode, writes will fail i.e. data will be lost, if the
+number of unconsumed sub-buffers equals the total number of
+sub-buffers in the channel.  It should be clear that if there is no
+consumer or if the consumer can't consume sub-buffers fast enought,
+data will be lost in either case; the only difference is whether data
+is lost from the beginning or the end of a buffer.
+
+As explained above, a relayfs channel is made of up one or more
+per-cpu channel buffers, each implemented as a circular buffer
+subdivided into one or more sub-buffers.  Messages are written into
+the current sub-buffer of the channel's current per-cpu buffer via the
+write functions described below.  Whenever a message can't fit into
+the current sub-buffer, because there's no room left for it, the
+client is notified via the subbuf_start() callback that a switch to a
+new sub-buffer is about to occur.  The client uses this callback to 1)
+initialize the next sub-buffer if appropriate 2) finalize the previous
+sub-buffer if appropriate and 3) return a boolean value indicating
+whether or not to actually go ahead with the sub-buffer switch.
+
+To implement 'no-overwrite' mode, the userspace client would provide
+an implementation of the subbuf_start() callback something like the
+following:
+
+static int subbuf_start(struct rchan_buf *buf,
+                        void *subbuf,
+			void *prev_subbuf,
+			unsigned int prev_padding)
+{
+	if (prev_subbuf)
+		*((unsigned *)prev_subbuf) = prev_padding;
+
+	if (relay_buf_full(buf))
+		return 0;
+
+	subbuf_start_reserve(buf, sizeof(unsigned int));
+
+	return 1;
+}
+
+If the current buffer is full i.e. all sub-buffers remain unconsumed,
+the callback returns 0 to indicate that the buffer switch should not
+occur yet i.e. until the consumer has had a chance to read the current
+set of ready sub-buffers.  For the relay_buf_full() function to make
+sense, the consumer is reponsible for notifying relayfs when
+sub-buffers have been consumed via relay_subbufs_consumed().  Any
+subsequent attempts to write into the buffer will again invoke the
+subbuf_start() callback with the same parameters; only when the
+consumer has consumed one or more of the ready sub-buffers will
+relay_buf_full() return 0, in which case the buffer switch can
+continue.
+
+The implementation of the subbuf_start() callback for 'overwrite' mode
+would be very similar:
+
+static int subbuf_start(struct rchan_buf *buf,
+                        void *subbuf,
+			void *prev_subbuf,
+			unsigned int prev_padding)
+{
+	if (prev_subbuf)
+		*((unsigned *)prev_subbuf) = prev_padding;
+
+	subbuf_start_reserve(buf, sizeof(unsigned int));
+
+	return 1;
+}
+
+In this case, the relay_buf_full() check is meaningless and the
+callback always returns 1, causing the buffer switch to occur
+unconditionally.  It's also meaningless for the client to use the
+relay_subbufs_consumed() function in this mode, as it's never
+consulted.
+
+The default subbuf_start() implementation, used if the client doesn't
+define any callbacks, or doesn't define the subbuf_start() callback,
+implements the simplest possible 'no-overwrite' mode i.e. it does
+nothing but return 0.
+
+Header information can be reserved at the beginning of each sub-buffer
+by calling the subbuf_start_reserve() helper function from within the
+subbuf_start() callback.  This reserved area can be used to store
+whatever information the client wants.  In the example above, room is
+reserved in each sub-buffer to store the padding count for that
+sub-buffer.  This is filled in for the previous sub-buffer in the
+subbuf_start() implementation; the padding value for the previous
+sub-buffer is passed into the subbuf_start() callback along with a
+pointer to the previous sub-buffer, since the padding value isn't
+known until a sub-buffer is filled.  The subbuf_start() callback is
+also called for the first sub-buffer when the channel is opened, to
+give the client a chance to reserve space in it.  In this case the
+previous sub-buffer pointer passed into the callback will be NULL, so
+the client should check the value of the prev_subbuf pointer before
+writing into the previous sub-buffer.
+
+Writing to a channel
+--------------------
+
+kernel clients write data into the current cpu's channel buffer using
+relay_write() or __relay_write().  relay_write() is the main logging
+function - it uses local_irqsave() to protect the buffer and should be
+used if you might be logging from interrupt context.  If you know
+you'll never be logging from interrupt context, you can use
+__relay_write(), which only disables preemption.  These functions
+don't return a value, so you can't determine whether or not they
+failed - the assumption is that you wouldn't want to check a return
+value in the fast logging path anyway, and that they'll always succeed
+unless the buffer is full and no-overwrite mode is being used, in
+which case you can detect a failed write in the subbuf_start()
+callback by calling the relay_buf_full() helper function.
+
+relay_reserve() is used to reserve a slot in a channel buffer which
+can be written to later.  This would typically be used in applications
+that need to write directly into a channel buffer without having to
+stage data in a temporary buffer beforehand.  Because the actual write
+may not happen immediately after the slot is reserved, applications
+using relay_reserve() can keep a count of the number of bytes actually
+written, either in space reserved in the sub-buffers themselves or as
+a separate array.  See the 'reserve' example in the relay-apps tarball
+at http://relayfs.sourceforge.net for an example of how this can be
+done.  Because the write is under control of the client and is
+separated from the reserve, relay_reserve() doesn't protect the buffer
+at all - it's up to the client to provide the appropriate
+synchronization when using relay_reserve().
+
+Closing a channel
+-----------------
+
+The client calls relay_close() when it's finished using the channel.
+The channel and its associated buffers are destroyed when there are no
+longer any references to any of the channel buffers.  relay_flush()
+forces a sub-buffer switch on all the channel buffers, and can be used
+to finalize and process the last sub-buffers before the channel is
+closed.
+
+Misc
+----
+
+Some applications may want to keep a channel around and re-use it
+rather than open and close a new channel for each use.  relay_reset()
+can be used for this purpose - it resets a channel to its initial
+state without reallocating channel buffer memory or destroying
+existing mappings.  It should however only be called when it's safe to
+do so i.e. when the channel isn't currently being written to.
+
+Finally, there are a couple of utility callbacks that can be used for
+different purposes.  buf_mapped() is called whenever a channel buffer
+is mmapped from user space and buf_unmapped() is called when it's
+unmapped.  The client can use this notification to trigger actions
+within the kernel application, such as enabling/disabling logging to
+the channel.
+
+
+Resources
+=========
+
+For news, example code, mailing list, etc. see the relayfs homepage:
+
+    http://relayfs.sourceforge.net
+
+
+Credits
+=======
+
+The ideas and specs for relayfs came about as a result of discussions
+on tracing involving the following:
+
+Michel Dagenais		<michel.dagenais@polymtl.ca>
+Richard Moore		<richardj_moore@uk.ibm.com>
+Bob Wisniewski		<bob@watson.ibm.com>
+Karim Yaghmour		<karim@opersys.com>
+Tom Zanussi		<zanussi@us.ibm.com>
+
+Also thanks to Hubertus Franke for a lot of useful suggestions and bug
+reports.
diff --git a/Documentation/filesystems/sysfs.txt b/Documentation/filesystems/sysfs.txt
index dc276598a65..c8bce82ddca 100644
--- a/Documentation/filesystems/sysfs.txt
+++ b/Documentation/filesystems/sysfs.txt
@@ -90,7 +90,7 @@ void device_remove_file(struct device *, struct device_attribute *);
 
 It also defines this helper for defining device attributes: 
 
-#define DEVICE_ATTR(_name,_mode,_show,_store)      \
+#define DEVICE_ATTR(_name, _mode, _show, _store)      \
 struct device_attribute dev_attr_##_name = {            \
         .attr = {.name  = __stringify(_name) , .mode   = _mode },      \
         .show   = _show,                                \
@@ -99,14 +99,14 @@ struct device_attribute dev_attr_##_name = {            \
 
 For example, declaring
 
-static DEVICE_ATTR(foo,0644,show_foo,store_foo);
+static DEVICE_ATTR(foo, S_IWUSR | S_IRUGO, show_foo, store_foo);
 
 is equivalent to doing:
 
 static struct device_attribute dev_attr_foo = {
        .attr	= {
 		.name = "foo",
-		.mode = 0644,
+		.mode = S_IWUSR | S_IRUGO,
 	},
 	.show = show_foo,
 	.store = store_foo,
@@ -121,8 +121,8 @@ set of sysfs operations for forwarding read and write calls to the
 show and store methods of the attribute owners. 
 
 struct sysfs_ops {
-        ssize_t (*show)(struct kobject *, struct attribute *,char *);
-        ssize_t (*store)(struct kobject *,struct attribute *,const char *);
+        ssize_t (*show)(struct kobject *, struct attribute *, char *);
+        ssize_t (*store)(struct kobject *, struct attribute *, const char *);
 };
 
 [ Subsystems should have already defined a struct kobj_type as a
@@ -137,7 +137,7 @@ calls the associated methods.
 
 To illustrate:
 
-#define to_dev_attr(_attr) container_of(_attr,struct device_attribute,attr)
+#define to_dev_attr(_attr) container_of(_attr, struct device_attribute, attr)
 #define to_dev(d) container_of(d, struct device, kobj)
 
 static ssize_t
@@ -148,7 +148,7 @@ dev_attr_show(struct kobject * kobj, struct attribute * attr, char * buf)
         ssize_t ret = 0;
 
         if (dev_attr->show)
-                ret = dev_attr->show(dev,buf);
+                ret = dev_attr->show(dev, buf);
         return ret;
 }
 
@@ -216,16 +216,16 @@ A very simple (and naive) implementation of a device attribute is:
 
 static ssize_t show_name(struct device *dev, struct device_attribute *attr, char *buf)
 {
-        return sprintf(buf,"%s\n",dev->name);
+	return snprintf(buf, PAGE_SIZE, "%s\n", dev->name);
 }
 
 static ssize_t store_name(struct device * dev, const char * buf)
 {
-	sscanf(buf,"%20s",dev->name);
-	return strlen(buf);
+	sscanf(buf, "%20s", dev->name);
+	return strnlen(buf, PAGE_SIZE);
 }
 
-static DEVICE_ATTR(name,S_IRUGO,show_name,store_name);
+static DEVICE_ATTR(name, S_IRUGO, show_name, store_name);
 
 
 (Note that the real implementation doesn't allow userspace to set the 
@@ -290,7 +290,7 @@ struct device_attribute {
 
 Declaring:
 
-DEVICE_ATTR(_name,_str,_mode,_show,_store);
+DEVICE_ATTR(_name, _str, _mode, _show, _store);
 
 Creation/Removal:
 
@@ -310,7 +310,7 @@ struct bus_attribute {
 
 Declaring:
 
-BUS_ATTR(_name,_mode,_show,_store)
+BUS_ATTR(_name, _mode, _show, _store)
 
 Creation/Removal:
 
@@ -331,7 +331,7 @@ struct driver_attribute {
 
 Declaring:
 
-DRIVER_ATTR(_name,_mode,_show,_store)
+DRIVER_ATTR(_name, _mode, _show, _store)
 
 Creation/Removal:
 
diff --git a/Documentation/hwmon/lm78 b/Documentation/hwmon/lm78
index 357086ed7f6..fd5dc7a19f0 100644
--- a/Documentation/hwmon/lm78
+++ b/Documentation/hwmon/lm78
@@ -2,16 +2,11 @@ Kernel driver lm78
 ==================
 
 Supported chips:
-  * National Semiconductor LM78
+  * National Semiconductor LM78 / LM78-J
     Prefix: 'lm78'
     Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports)
     Datasheet: Publicly available at the National Semiconductor website
                http://www.national.com/
-  * National Semiconductor LM78-J
-    Prefix: 'lm78-j'
-    Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports)
-    Datasheet: Publicly available at the National Semiconductor website
-               http://www.national.com/
   * National Semiconductor LM79
     Prefix: 'lm79'
     Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports)
diff --git a/Documentation/hwmon/w83792d b/Documentation/hwmon/w83792d
new file mode 100644
index 00000000000..8171c285bb5
--- /dev/null
+++ b/Documentation/hwmon/w83792d
@@ -0,0 +1,174 @@
+Kernel driver w83792d
+=====================
+
+Supported chips:
+  * Winbond W83792D
+    Prefix: 'w83792d'
+    Addresses scanned: I2C 0x2c - 0x2f
+    Datasheet: http://www.winbond.com.tw/E-WINBONDHTM/partner/PDFresult.asp?Pname=1035
+
+Author: Chunhao Huang
+Contact: DZShen <DZShen@Winbond.com.tw>
+
+
+Module Parameters
+-----------------
+
+* init int
+  (default 1)
+  Use 'init=0' to bypass initializing the chip.
+  Try this if your computer crashes when you load the module.
+
+* force_subclients=bus,caddr,saddr,saddr
+  This is used to force the i2c addresses for subclients of
+  a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b'
+  to force the subclients of chip 0x2f on bus 0 to i2c addresses
+  0x4a and 0x4b.
+
+
+Description
+-----------
+
+This driver implements support for the Winbond W83792AD/D.
+
+Detection of the chip can sometimes be foiled because it can be in an
+internal state that allows no clean access (Bank with ID register is not
+currently selected). If you know the address of the chip, use a 'force'
+parameter; this will put it into a more well-behaved state first.
+
+The driver implements three temperature sensors, seven fan rotation speed
+sensors, nine voltage sensors, and two automatic fan regulation
+strategies called: Smart Fan I (Thermal Cruise mode) and Smart Fan II.
+Automatic fan control mode is possible only for fan1-fan3. Fan4-fan7 can run
+synchronized with selected fan (fan1-fan3). This functionality and manual PWM
+control for fan4-fan7 is not yet implemented.
+
+Temperatures are measured in degrees Celsius and measurement resolution is 1
+degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
+the temperature gets higher than the Overtemperature Shutdown value; it stays
+on until the temperature falls below the Hysteresis value.
+
+Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
+triggered if the rotation speed has dropped below a programmable limit. Fan
+readings can be divided by a programmable divider (1, 2, 4, 8, 16, 32, 64 or
+128) to give the readings more range or accuracy.
+
+Voltage sensors (also known as IN sensors) report their values in millivolts.
+An alarm is triggered if the voltage has crossed a programmable minimum
+or maximum limit.
+
+Alarms are provided as output from "realtime status register". Following bits
+are defined:
+
+bit - alarm on:
+0  - in0
+1  - in1
+2  - temp1
+3  - temp2
+4  - temp3
+5  - fan1
+6  - fan2
+7  - fan3
+8  - in2
+9  - in3
+10 - in4
+11 - in5
+12 - in6
+13 - VID change
+14 - chassis
+15 - fan7
+16 - tart1
+17 - tart2
+18 - tart3
+19 - in7
+20 - in8
+21 - fan4
+22 - fan5
+23 - fan6
+
+Tart will be asserted while target temperature cannot be achieved after 3 minutes
+of full speed rotation of corresponding fan.
+
+In addition to the alarms described above, there is a CHAS alarm on the chips
+which triggers if your computer case is open (This one is latched, contrary
+to realtime alarms).
+
+The chips only update values each 3 seconds; reading them more often will
+do no harm, but will return 'old' values.
+
+
+W83792D PROBLEMS
+----------------
+Known problems:
+	- This driver is only for Winbond W83792D C version device, there
+	  are also some motherboards with B version W83792D device. The
+	  calculation method to in6-in7(measured value, limits) is a little
+	  different between C and B version. C or B version can be identified
+	  by CR[0x49h].
+	- The function of vid and vrm has not been finished, because I'm NOT
+	  very familiar with them. Adding support is welcome.
+ 	- The function of chassis open detection needs more tests.
+	- If you have ASUS server board and chip was not found: Then you will
+	  need to upgrade to latest (or beta) BIOS. If it does not help please
+	  contact us.
+
+Fan control
+-----------
+
+Manual mode
+-----------
+
+Works as expected. You just need to specify desired PWM/DC value (fan speed)
+in appropriate pwm# file.
+
+Thermal cruise
+--------------
+
+In this mode, W83792D provides the Smart Fan system to automatically control
+fan speed to keep the temperatures of CPU and the system within specific
+range. At first a wanted temperature and interval must be set. This is done
+via thermal_cruise# file. The tolerance# file serves to create T +- tolerance
+interval. The fan speed will be lowered as long as the current temperature
+remains below the thermal_cruise# +- tolerance# value. Once the temperature
+exceeds the high limit (T+tolerance), the fan will be turned on with a
+specific speed set by pwm# and automatically controlled its PWM duty cycle
+with the temperature varying. Three conditions may occur:
+
+(1) If the temperature still exceeds the high limit, PWM duty
+cycle will increase slowly.
+
+(2) If the temperature goes below the high limit, but still above the low
+limit (T-tolerance), the fan speed will be fixed at the current speed because
+the temperature is in the target range.
+
+(3) If the temperature goes below the low limit, PWM duty cycle will decrease
+slowly to 0 or a preset stop value until the temperature exceeds the low
+limit. (The preset stop value handling is not yet implemented in driver)
+
+Smart Fan II
+------------
+
+W83792D also provides a special mode for fan. Four temperature points are
+available. When related temperature sensors detects the temperature in preset
+temperature region (sf2_point@_fan# +- tolerance#) it will cause fans to run
+on programmed value from sf2_level@_fan#. You need to set four temperatures
+for each fan.
+
+
+/sys files
+----------
+
+pwm[1-3] - this file stores PWM duty cycle or DC value (fan speed) in range:
+	0 (stop) to 255 (full)
+pwm[1-3]_enable - this file controls mode of fan/temperature control:
+            * 0 Disabled
+            * 1 Manual mode
+            * 2 Smart Fan II
+            * 3 Thermal Cruise
+pwm[1-3]_mode - Select PWM of DC mode
+            * 0 DC
+            * 1 PWM
+thermal_cruise[1-3] - Selects the desired temperature for cruise (degC)
+tolerance[1-3] - Value in degrees of Celsius (degC) for +- T
+sf2_point[1-4]_fan[1-3] - four temperature points for each fan for Smart Fan II
+sf2_level[1-3]_fan[1-3] - three PWM/DC levels for each fan for Smart Fan II
diff --git a/Documentation/i2c/chips/max6875 b/Documentation/i2c/chips/max6875
index b02002898a0..96fec562a8e 100644
--- a/Documentation/i2c/chips/max6875
+++ b/Documentation/i2c/chips/max6875
@@ -4,22 +4,13 @@ Kernel driver max6875
 Supported chips:
   * Maxim MAX6874, MAX6875
     Prefix: 'max6875'
-    Addresses scanned: 0x50, 0x52
+    Addresses scanned: None (see below)
     Datasheet:
         http://pdfserv.maxim-ic.com/en/ds/MAX6874-MAX6875.pdf
 
 Author: Ben Gardner <bgardner@wabtec.com>
 
 
-Module Parameters
------------------
-
-* allow_write int
-  Set to non-zero to enable write permission:
-  *0: Read only
-   1: Read and write
-
-
 Description
 -----------
 
@@ -33,34 +24,85 @@ registers.
 
 The Maxim MAX6874 is a similar, mostly compatible device, with more intputs
 and outputs:
-
              vin     gpi    vout
 MAX6874        6       4       8
 MAX6875        4       3       5
 
-MAX6874 chips can have four different addresses (as opposed to only two for
-the MAX6875). The additional addresses (0x54 and 0x56) are not probed by
-this driver by default, but the probe module parameter can be used if
-needed.
-
-See the datasheet for details on how to program the EEPROM.
+See the datasheet for more information.
 
 
 Sysfs entries
 -------------
 
-eeprom_user   - 512 bytes of user-defined EEPROM space. Only writable if
-                allow_write was set and register 0x43 is 0.
-
-eeprom_config - 70 bytes of config EEPROM. Note that changes will not get
-                loaded into register space until a power cycle or device reset.
-
-reg_config    - 70 bytes of register space. Any changes take affect immediately.
+eeprom        - 512 bytes of user-defined EEPROM space.
 
 
 General Remarks
 ---------------
 
-A typical application will require that the EEPROMs be programmed once and
-never altered afterwards.
+Valid addresses for the MAX6875 are 0x50 and 0x52.
+Valid addresses for the MAX6874 are 0x50, 0x52, 0x54 and 0x56.
+The driver does not probe any address, so you must force the address.
+
+Example:
+$ modprobe max6875 force=0,0x50
+
+The MAX6874/MAX6875 ignores address bit 0, so this driver attaches to multiple
+addresses.  For example, for address 0x50, it also reserves 0x51.
+The even-address instance is called 'max6875', the odd one is 'max6875 subclient'.
+
+
+Programming the chip using i2c-dev
+----------------------------------
+
+Use the i2c-dev interface to access and program the chips.
+Reads and writes are performed differently depending on the address range.
+
+The configuration registers are at addresses 0x00 - 0x45.
+Use i2c_smbus_write_byte_data() to write a register and
+i2c_smbus_read_byte_data() to read a register.
+The command is the register number.
+
+Examples:
+To write a 1 to register 0x45:
+  i2c_smbus_write_byte_data(fd, 0x45, 1);
+
+To read register 0x45:
+  value = i2c_smbus_read_byte_data(fd, 0x45);
+
+
+The configuration EEPROM is at addresses 0x8000 - 0x8045.
+The user EEPROM is at addresses 0x8100 - 0x82ff.
+
+Use i2c_smbus_write_word_data() to write a byte to EEPROM.
+
+The command is the upper byte of the address: 0x80, 0x81, or 0x82.
+The data word is the lower part of the address or'd with data << 8.
+  cmd = address >> 8;
+  val = (address & 0xff) | (data << 8);
+
+Example:
+To write 0x5a to address 0x8003:
+  i2c_smbus_write_word_data(fd, 0x80, 0x5a03);
+
+
+Reading data from the EEPROM is a little more complicated.
+Use i2c_smbus_write_byte_data() to set the read address and then
+i2c_smbus_read_byte() or i2c_smbus_read_i2c_block_data() to read the data.
+
+Example:
+To read data starting at offset 0x8100, first set the address:
+  i2c_smbus_write_byte_data(fd, 0x81, 0x00);
+
+And then read the data
+  value = i2c_smbus_read_byte(fd);
+
+  or
+
+  count = i2c_smbus_read_i2c_block_data(fd, 0x84, buffer);
+
+The block read should read 16 bytes.
+0x84 is the block read command.
+
+See the datasheet for more details.
 
diff --git a/Documentation/i2c/functionality b/Documentation/i2c/functionality
index 8a78a95ae04..41ffefbdc60 100644
--- a/Documentation/i2c/functionality
+++ b/Documentation/i2c/functionality
@@ -115,7 +115,7 @@ CHECKING THROUGH /DEV
 If you try to access an adapter from a userspace program, you will have
 to use the /dev interface. You will still have to check whether the
 functionality you need is supported, of course. This is done using
-the I2C_FUNCS ioctl. An example, adapted from the lm_sensors i2c_detect
+the I2C_FUNCS ioctl. An example, adapted from the lm_sensors i2cdetect
 program, is below:
 
   int file;
diff --git a/Documentation/i2c/porting-clients b/Documentation/i2c/porting-clients
index a7adbdd9ea8..4849dfd6961 100644
--- a/Documentation/i2c/porting-clients
+++ b/Documentation/i2c/porting-clients
@@ -1,4 +1,4 @@
-Revision 4, 2004-03-30
+Revision 5, 2005-07-29
 Jean Delvare <khali@linux-fr.org>
 Greg KH <greg@kroah.com>
 
@@ -17,20 +17,22 @@ yours for best results.
 
 Technical changes:
 
-* [Includes] Get rid of "version.h". Replace <linux/i2c-proc.h> with
-  <linux/i2c-sensor.h>. Includes typically look like that:
+* [Includes] Get rid of "version.h" and <linux/i2c-proc.h>.
+  Includes typically look like that:
   #include <linux/module.h>
   #include <linux/init.h>
   #include <linux/slab.h>
   #include <linux/i2c.h>
-  #include <linux/i2c-sensor.h>
-  #include <linux/i2c-vid.h>	/* if you need VRM support */
+  #include <linux/hwmon.h>	/* for hardware monitoring drivers */
+  #include <linux/hwmon-sysfs.h>
+  #include <linux/hwmon-vid.h>	/* if you need VRM support */
   #include <asm/io.h>		/* if you have I/O operations */
   Please respect this inclusion order. Some extra headers may be
   required for a given driver (e.g. "lm75.h").
 
-* [Addresses] SENSORS_I2C_END becomes I2C_CLIENT_END, SENSORS_ISA_END
-  becomes I2C_CLIENT_ISA_END.
+* [Addresses] SENSORS_I2C_END becomes I2C_CLIENT_END, ISA addresses
+  are no more handled by the i2c core.
+  SENSORS_INSMOD_<n> becomes I2C_CLIENT_INSMOD_<n>.
 
 * [Client data] Get rid of sysctl_id. Try using standard names for
   register values (for example, temp_os becomes temp_max). You're
@@ -66,13 +68,15 @@ Technical changes:
   if (!(adapter->class & I2C_CLASS_HWMON))
           return 0;
   ISA-only drivers of course don't need this.
+  Call i2c_probe() instead of i2c_detect().
 
 * [Detect] As mentioned earlier, the flags parameter is gone.
   The type_name and client_name strings are replaced by a single
   name string, which will be filled with a lowercase, short string
   (typically the driver name, e.g. "lm75").
   In i2c-only drivers, drop the i2c_is_isa_adapter check, it's
-  useless.
+  useless. Same for isa-only drivers, as the test would always be
+  true. Only hybrid drivers (which are quite rare) still need it.
   The errorN labels are reduced to the number needed. If that number
   is 2 (i2c-only drivers), it is advised that the labels are named
   exit and exit_free. For i2c+isa drivers, labels should be named
@@ -86,6 +90,8 @@ Technical changes:
   device_create_file. Move the driver initialization before any
   sysfs file creation.
   Drop client->id.
+  Drop any 24RF08 corruption prevention you find, as this is now done
+  at the i2c-core level, and doing it twice voids it.
 
 * [Init] Limits must not be set by the driver (can be done later in
   user-space). Chip should not be reset default (although a module
@@ -93,7 +99,8 @@ Technical changes:
   limited to the strictly necessary steps.
 
 * [Detach] Get rid of data, remove the call to
-  i2c_deregister_entry.
+  i2c_deregister_entry. Do not log an error message if
+  i2c_detach_client fails, as i2c-core will now do it for you.
 
 * [Update] Don't access client->data directly, use
   i2c_get_clientdata(client) instead.
diff --git a/Documentation/i2c/writing-clients b/Documentation/i2c/writing-clients
index 91664be91ff..077275722a7 100644
--- a/Documentation/i2c/writing-clients
+++ b/Documentation/i2c/writing-clients
@@ -148,15 +148,15 @@ are defined in i2c.h to help you support them, as well as a generic
 detection algorithm.
 
 You do not have to use this parameter interface; but don't try to use
-function i2c_probe() (or i2c_detect()) if you don't.
+function i2c_probe() if you don't.
 
 NOTE: If you want to write a `sensors' driver, the interface is slightly
       different! See below.
 
 
 
-Probing classes (i2c)
----------------------
+Probing classes
+---------------
 
 All parameters are given as lists of unsigned 16-bit integers. Lists are
 terminated by I2C_CLIENT_END.
@@ -171,12 +171,18 @@ The following lists are used internally:
    ignore: insmod parameter.
      A list of pairs. The first value is a bus number (-1 for any I2C bus), 
      the second is the I2C address. These addresses are never probed. 
-     This parameter overrules 'normal' and 'probe', but not the 'force' lists.
+     This parameter overrules the 'normal_i2c' list only.
    force: insmod parameter. 
      A list of pairs. The first value is a bus number (-1 for any I2C bus),
      the second is the I2C address. A device is blindly assumed to be on
      the given address, no probing is done. 
 
+Additionally, kind-specific force lists may optionally be defined if
+the driver supports several chip kinds. They are grouped in a
+NULL-terminated list of pointers named forces, those first element if the
+generic force list mentioned above. Each additional list correspond to an
+insmod parameter of the form force_<kind>.
+
 Fortunately, as a module writer, you just have to define the `normal_i2c' 
 parameter. The complete declaration could look like this:
 
@@ -186,66 +192,17 @@ parameter. The complete declaration could look like this:
 
   /* Magic definition of all other variables and things */
   I2C_CLIENT_INSMOD;
+  /* Or, if your driver supports, say, 2 kind of devices: */
+  I2C_CLIENT_INSMOD_2(foo, bar);
+
+If you use the multi-kind form, an enum will be defined for you:
+  enum chips { any_chip, foo, bar, ... }
+You can then (and certainly should) use it in the driver code.
 
 Note that you *have* to call the defined variable `normal_i2c',
 without any prefix!
 
 
-Probing classes (sensors)
--------------------------
-
-If you write a `sensors' driver, you use a slightly different interface.
-As well as I2C addresses, we have to cope with ISA addresses. Also, we
-use a enum of chip types. Don't forget to include `sensors.h'.
-
-The following lists are used internally. They are all lists of integers.
-
-   normal_i2c: filled in by the module writer. Terminated by SENSORS_I2C_END.
-     A list of I2C addresses which should normally be examined.
-   normal_isa: filled in by the module writer. Terminated by SENSORS_ISA_END.
-     A list of ISA addresses which should normally be examined.
-   probe: insmod parameter. Initialize this list with SENSORS_I2C_END values.
-     A list of pairs. The first value is a bus number (SENSORS_ISA_BUS for
-     the ISA bus, -1 for any I2C bus), the second is the address. These
-     addresses are also probed, as if they were in the 'normal' list.
-   ignore: insmod parameter. Initialize this list with SENSORS_I2C_END values.
-     A list of pairs. The first value is a bus number (SENSORS_ISA_BUS for
-     the ISA bus, -1 for any I2C bus), the second is the I2C address. These
-     addresses are never probed. This parameter overrules 'normal' and 
-     'probe', but not the 'force' lists.
-
-Also used is a list of pointers to sensors_force_data structures:
-   force_data: insmod parameters. A list, ending with an element of which
-     the force field is NULL.
-     Each element contains the type of chip and a list of pairs.
-     The first value is a bus number (SENSORS_ISA_BUS for the ISA bus, 
-     -1 for any I2C bus), the second is the address. 
-     These are automatically translated to insmod variables of the form
-     force_foo.
-
-So we have a generic insmod variabled `force', and chip-specific variables
-`force_CHIPNAME'.
-
-Fortunately, as a module writer, you just have to define the `normal_i2c' 
-and `normal_isa' parameters, and define what chip names are used. 
-The complete declaration could look like this:
-  /* Scan i2c addresses 0x37, and 0x48 to 0x4f */
-  static unsigned short normal_i2c[] = { 0x37, 0x48, 0x49, 0x4a, 0x4b, 0x4c,
-                                         0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
-  /* Scan ISA address 0x290 */
-  static unsigned int normal_isa[] = {0x0290,SENSORS_ISA_END};
-
-  /* Define chips foo and bar, as well as all module parameters and things */
-  SENSORS_INSMOD_2(foo,bar);
-
-If you have one chip, you use macro SENSORS_INSMOD_1(chip), if you have 2
-you use macro SENSORS_INSMOD_2(chip1,chip2), etc. If you do not want to
-bother with chip types, you can use SENSORS_INSMOD_0.
-
-A enum is automatically defined as follows:
-  enum chips { any_chip, chip1, chip2, ... }
-
-
 Attaching to an adapter
 -----------------------
 
@@ -264,17 +221,10 @@ detected at a specific address, another callback is called.
     return i2c_probe(adapter,&addr_data,&foo_detect_client);
   }
 
-For `sensors' drivers, use the i2c_detect function instead:
-  
-  int foo_attach_adapter(struct i2c_adapter *adapter)
-  { 
-    return i2c_detect(adapter,&addr_data,&foo_detect_client);
-  }
-
 Remember, structure `addr_data' is defined by the macros explained above,
 so you do not have to define it yourself.
 
-The i2c_probe or i2c_detect function will call the foo_detect_client
+The i2c_probe function will call the foo_detect_client
 function only for those i2c addresses that actually have a device on
 them (unless a `force' parameter was used). In addition, addresses that
 are already in use (by some other registered client) are skipped.
@@ -283,19 +233,18 @@ are already in use (by some other registered client) are skipped.
 The detect client function
 --------------------------
 
-The detect client function is called by i2c_probe or i2c_detect.
-The `kind' parameter contains 0 if this call is due to a `force'
-parameter, and -1 otherwise (for i2c_detect, it contains 0 if
-this call is due to the generic `force' parameter, and the chip type
-number if it is due to a specific `force' parameter).
+The detect client function is called by i2c_probe. The `kind' parameter
+contains -1 for a probed detection, 0 for a forced detection, or a positive
+number for a forced detection with a chip type forced.
 
 Below, some things are only needed if this is a `sensors' driver. Those
 parts are between /* SENSORS ONLY START */ and /* SENSORS ONLY END */
 markers. 
 
-This function should only return an error (any value != 0) if there is
-some reason why no more detection should be done anymore. If the
-detection just fails for this address, return 0.
+Returning an error different from -ENODEV in a detect function will cause
+the detection to stop: other addresses and adapters won't be scanned.
+This should only be done on fatal or internal errors, such as a memory
+shortage or i2c_attach_client failing.
 
 For now, you can ignore the `flags' parameter. It is there for future use.
 
@@ -320,11 +269,10 @@ For now, you can ignore the `flags' parameter. It is there for future use.
     const char *type_name = "";
     int is_isa = i2c_is_isa_adapter(adapter);
 
-    if (is_isa) {
+    /* Do this only if the chip can additionally be found on the ISA bus
+       (hybrid chip). */
 
-      /* If this client can't be on the ISA bus at all, we can stop now
-         (call `goto ERROR0'). But for kicks, we will assume it is all
-         right. */
+    if (is_isa) {
 
       /* Discard immediately if this ISA range is already used */
       if (check_region(address,FOO_EXTENT))
@@ -495,15 +443,13 @@ much simpler than the attachment code, fortunately!
     /* SENSORS ONLY END */
 
     /* Try to detach the client from i2c space */
-    if ((err = i2c_detach_client(client))) {
-      printk("foo.o: Client deregistration failed, client not detached.\n");
+    if ((err = i2c_detach_client(client)))
       return err;
-    }
 
-    /* SENSORS ONLY START */
+    /* HYBRID SENSORS CHIP ONLY START */
     if i2c_is_isa_client(client)
       release_region(client->addr,LM78_EXTENT);
-    /* SENSORS ONLY END */
+    /* HYBRID SENSORS CHIP ONLY END */
 
     kfree(client); /* Frees client data too, if allocated at the same time */
     return 0;
diff --git a/Documentation/i386/boot.txt b/Documentation/i386/boot.txt
index 1c48f0eba6f..10312bebe55 100644
--- a/Documentation/i386/boot.txt
+++ b/Documentation/i386/boot.txt
@@ -2,7 +2,7 @@
 		     ----------------------------
 
 		    H. Peter Anvin <hpa@zytor.com>
-			Last update 2002-01-01
+			Last update 2005-09-02
 
 On the i386 platform, the Linux kernel uses a rather complicated boot
 convention.  This has evolved partially due to historical aspects, as
@@ -34,6 +34,8 @@ Protocol 2.02:	(Kernel 2.4.0-test3-pre3) New command line protocol.
 Protocol 2.03:	(Kernel 2.4.18-pre1) Explicitly makes the highest possible
 		initrd address available to the bootloader.
 
+Protocol 2.04:	(Kernel 2.6.14) Extend the syssize field to four bytes.
+
 
 **** MEMORY LAYOUT
 
@@ -103,10 +105,9 @@ The header looks like:
 Offset	Proto	Name		Meaning
 /Size
 
-01F1/1	ALL	setup_sects	The size of the setup in sectors
+01F1/1	ALL(1	setup_sects	The size of the setup in sectors
 01F2/2	ALL	root_flags	If set, the root is mounted readonly
-01F4/2	ALL	syssize		DO NOT USE - for bootsect.S use only
-01F6/2	ALL	swap_dev	DO NOT USE - obsolete
+01F4/4	2.04+(2	syssize		The size of the 32-bit code in 16-byte paras
 01F8/2	ALL	ram_size	DO NOT USE - for bootsect.S use only
 01FA/2	ALL	vid_mode	Video mode control
 01FC/2	ALL	root_dev	Default root device number
@@ -129,8 +130,12 @@ Offset	Proto	Name		Meaning
 0228/4	2.02+	cmd_line_ptr	32-bit pointer to the kernel command line
 022C/4	2.03+	initrd_addr_max	Highest legal initrd address
 
-For backwards compatibility, if the setup_sects field contains 0, the
-real value is 4.
+(1) For backwards compatibility, if the setup_sects field contains 0, the
+    real value is 4.
+
+(2) For boot protocol prior to 2.04, the upper two bytes of the syssize
+    field are unusable, which means the size of a bzImage kernel
+    cannot be determined.
 
 If the "HdrS" (0x53726448) magic number is not found at offset 0x202,
 the boot protocol version is "old".  Loading an old kernel, the
@@ -230,12 +235,16 @@ loader to communicate with the kernel.  Some of its options are also
 relevant to the boot loader itself, see "special command line options"
 below.
 
-The kernel command line is a null-terminated string up to 255
-characters long, plus the final null.
+The kernel command line is a null-terminated string currently up to
+255 characters long, plus the final null.  A string that is too long
+will be automatically truncated by the kernel, a boot loader may allow
+a longer command line to be passed to permit future kernels to extend
+this limit.
 
 If the boot protocol version is 2.02 or later, the address of the
 kernel command line is given by the header field cmd_line_ptr (see
-above.)
+above.)  This address can be anywhere between the end of the setup
+heap and 0xA0000.
 
 If the protocol version is *not* 2.02 or higher, the kernel
 command line is entered using the following protocol:
@@ -255,7 +264,7 @@ command line is entered using the following protocol:
 **** SAMPLE BOOT CONFIGURATION
 
 As a sample configuration, assume the following layout of the real
-mode segment:
+mode segment (this is a typical, and recommended layout):
 
 	0x0000-0x7FFF	Real mode kernel
 	0x8000-0x8FFF	Stack and heap
@@ -312,9 +321,9 @@ Such a boot loader should enter the following fields in the header:
 
 **** LOADING THE REST OF THE KERNEL
 
-The non-real-mode kernel starts at offset (setup_sects+1)*512 in the
-kernel file (again, if setup_sects == 0 the real value is 4.)  It
-should be loaded at address 0x10000 for Image/zImage kernels and
+The 32-bit (non-real-mode) kernel starts at offset (setup_sects+1)*512
+in the kernel file (again, if setup_sects == 0 the real value is 4.)
+It should be loaded at address 0x10000 for Image/zImage kernels and
 0x100000 for bzImage kernels.
 
 The kernel is a bzImage kernel if the protocol >= 2.00 and the 0x01
diff --git a/Documentation/kbuild/makefiles.txt b/Documentation/kbuild/makefiles.txt
index 2616a58a5a4..9a1586590d8 100644
--- a/Documentation/kbuild/makefiles.txt
+++ b/Documentation/kbuild/makefiles.txt
@@ -872,7 +872,13 @@ When kbuild executes the following steps are followed (roughly):
 	Assignments to $(targets) are without $(obj)/ prefix.
 	if_changed may be used in conjunction with custom commands as
 	defined in 6.7 "Custom kbuild commands".
+
 	Note: It is a typical mistake to forget the FORCE prerequisite.
+	Another common pitfall is that whitespace is sometimes
+	significant; for instance, the below will fail (note the extra space
+	after the comma):
+		target: source(s) FORCE
+	#WRONG!#	$(call if_changed, ld/objcopy/gzip)
 
     ld
 	Link target. Often LDFLAGS_$@ is used to set specific options to ld.
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 3d5cd7a09b2..d2f0c67ba1f 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1174,6 +1174,11 @@ running once the system is up.
 			New name for the ramdisk parameter.
 			See Documentation/ramdisk.txt.
 
+	rdinit=		[KNL]
+			Format: <full_path>
+			Run specified binary instead of /init from the ramdisk,
+			used for early userspace startup. See initrd.
+
 	reboot=		[BUGS=IA-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
 			Format: <reboot_mode>[,<reboot_mode2>[,...]]
 			See arch/*/kernel/reboot.c.
diff --git a/Documentation/power/swsusp-dmcrypt.txt b/Documentation/power/swsusp-dmcrypt.txt
new file mode 100644
index 00000000000..59931b46ff7
--- /dev/null
+++ b/Documentation/power/swsusp-dmcrypt.txt
@@ -0,0 +1,138 @@
+Author: Andreas Steinmetz <ast@domdv.de>
+
+
+How to use dm-crypt and swsusp together:
+========================================
+
+Some prerequisites:
+You know how dm-crypt works. If not, visit the following web page:
+http://www.saout.de/misc/dm-crypt/
+You have read Documentation/power/swsusp.txt and understand it.
+You did read Documentation/initrd.txt and know how an initrd works.
+You know how to create or how to modify an initrd.
+
+Now your system is properly set up, your disk is encrypted except for
+the swap device(s) and the boot partition which may contain a mini
+system for crypto setup and/or rescue purposes. You may even have
+an initrd that does your current crypto setup already.
+
+At this point you want to encrypt your swap, too. Still you want to
+be able to suspend using swsusp. This, however, means that you
+have to be able to either enter a passphrase or that you read
+the key(s) from an external device like a pcmcia flash disk
+or an usb stick prior to resume. So you need an initrd, that sets
+up dm-crypt and then asks swsusp to resume from the encrypted
+swap device.
+
+The most important thing is that you set up dm-crypt in such
+a way that the swap device you suspend to/resume from has
+always the same major/minor within the initrd as well as
+within your running system. The easiest way to achieve this is
+to always set up this swap device first with dmsetup, so that
+it will always look like the following:
+
+brw-------  1 root root 254, 0 Jul 28 13:37 /dev/mapper/swap0
+
+Now set up your kernel to use /dev/mapper/swap0 as the default
+resume partition, so your kernel .config contains:
+
+CONFIG_PM_STD_PARTITION="/dev/mapper/swap0"
+
+Prepare your boot loader to use the initrd you will create or
+modify. For lilo the simplest setup looks like the following
+lines:
+
+image=/boot/vmlinuz
+initrd=/boot/initrd.gz
+label=linux
+append="root=/dev/ram0 init=/linuxrc rw"
+
+Finally you need to create or modify your initrd. Lets assume
+you create an initrd that reads the required dm-crypt setup
+from a pcmcia flash disk card. The card is formatted with an ext2
+fs which resides on /dev/hde1 when the card is inserted. The
+card contains at least the encrypted swap setup in a file
+named "swapkey". /etc/fstab of your initrd contains something
+like the following:
+
+/dev/hda1   /mnt    ext3      ro                            0 0
+none        /proc   proc      defaults,noatime,nodiratime   0 0
+none        /sys    sysfs     defaults,noatime,nodiratime   0 0
+
+/dev/hda1 contains an unencrypted mini system that sets up all
+of your crypto devices, again by reading the setup from the
+pcmcia flash disk. What follows now is a /linuxrc for your
+initrd that allows you to resume from encrypted swap and that
+continues boot with your mini system on /dev/hda1 if resume
+does not happen:
+
+#!/bin/sh
+PATH=/sbin:/bin:/usr/sbin:/usr/bin
+mount /proc
+mount /sys
+mapped=0
+noresume=`grep -c noresume /proc/cmdline`
+if [ "$*" != "" ]
+then
+  noresume=1
+fi
+dmesg -n 1
+/sbin/cardmgr -q
+for i in 1 2 3 4 5 6 7 8 9 0
+do
+  if [ -f /proc/ide/hde/media ]
+  then
+    usleep 500000
+    mount -t ext2 -o ro /dev/hde1 /mnt
+    if [ -f /mnt/swapkey ]
+    then
+      dmsetup create swap0 /mnt/swapkey > /dev/null 2>&1 && mapped=1
+    fi
+    umount /mnt
+    break
+  fi
+  usleep 500000
+done
+killproc /sbin/cardmgr
+dmesg -n 6
+if [ $mapped = 1 ]
+then
+  if [ $noresume != 0 ]
+  then
+    mkswap /dev/mapper/swap0 > /dev/null 2>&1
+  fi
+  echo 254:0 > /sys/power/resume
+  dmsetup remove swap0
+fi
+umount /sys
+mount /mnt
+umount /proc
+cd /mnt
+pivot_root . mnt
+mount /proc
+umount -l /mnt
+umount /proc
+exec chroot . /sbin/init $* < dev/console > dev/console 2>&1
+
+Please don't mind the weird loop above, busybox's msh doesn't know
+the let statement. Now, what is happening in the script?
+First we have to decide if we want to try to resume, or not.
+We will not resume if booting with "noresume" or any parameters
+for init like "single" or "emergency" as boot parameters.
+
+Then we need to set up dmcrypt with the setup data from the
+pcmcia flash disk. If this succeeds we need to reset the swap
+device if we don't want to resume. The line "echo 254:0 > /sys/power/resume"
+then attempts to resume from the first device mapper device.
+Note that it is important to set the device in /sys/power/resume,
+regardless if resuming or not, otherwise later suspend will fail.
+If resume starts, script execution terminates here.
+
+Otherwise we just remove the encrypted swap device and leave it to the
+mini system on /dev/hda1 to set the whole crypto up (it is up to
+you to modify this to your taste).
+
+What then follows is the well known process to change the root
+file system and continue booting from there. I prefer to unmount
+the initrd prior to continue booting but it is up to you to modify
+this.
diff --git a/Documentation/power/swsusp.txt b/Documentation/power/swsusp.txt
index 7a6b7896645..b0d50840788 100644
--- a/Documentation/power/swsusp.txt
+++ b/Documentation/power/swsusp.txt
@@ -1,22 +1,20 @@
-From kernel/suspend.c:
+Some warnings, first.
 
  * BIG FAT WARNING *********************************************************
  *
- * If you have unsupported (*) devices using DMA...
- *				...say goodbye to your data.
- *
  * If you touch anything on disk between suspend and resume...
  *				...kiss your data goodbye.
  *
- * If your disk driver does not support suspend... (IDE does)
- *				...you'd better find out how to get along
- *				   without your data.
- *
- * If you change kernel command line between suspend and resume...
- *			        ...prepare for nasty fsck or worse.
+ * If you do resume from initrd after your filesystems are mounted...
+ *				...bye bye root partition.
+ *			[this is actually same case as above]
  *
- * If you change your hardware while system is suspended...
- *			        ...well, it was not good idea.
+ * If you have unsupported (*) devices using DMA, you may have some
+ * problems. If your disk driver does not support suspend... (IDE does),
+ * it may cause some problems, too. If you change kernel command line
+ * between suspend and resume, it may do something wrong. If you change
+ * your hardware while system is suspended... well, it was not good idea;
+ * but it will probably only crash.
  *
  * (*) suspend/resume support is needed to make it safe.
 
@@ -30,6 +28,13 @@ echo shutdown > /sys/power/disk; echo disk > /sys/power/state
 echo platform > /sys/power/disk; echo disk > /sys/power/state
 
 
+Encrypted suspend image:
+------------------------
+If you want to store your suspend image encrypted with a temporary
+key to prevent data gathering after resume you must compile
+crypto and the aes algorithm into the kernel - modules won't work
+as they cannot be loaded at resume time.
+
 
 Article about goals and implementation of Software Suspend for Linux
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
@@ -85,11 +90,6 @@ resume.
 You have your server on UPS. Power died, and UPS is indicating 30
 seconds to failure. What do you do? Suspend to disk.
 
-Ethernet card in your server died. You want to replace it. Your
-server is not hotplug capable. What do you do? Suspend to disk,
-replace ethernet card, resume. If you are fast your users will not
-even see broken connections.
-
 
 Q: Maybe I'm missing something, but why don't the regular I/O paths work?
 
@@ -117,31 +117,6 @@ Q: Does linux support ACPI S4?
 
 A: Yes. That's what echo platform > /sys/power/disk does.
 
-Q: My machine doesn't work with ACPI. How can I use swsusp than ?
-
-A: Do a reboot() syscall with right parameters. Warning: glibc gets in
-its way, so check with strace:
-
-reboot(LINUX_REBOOT_MAGIC1, LINUX_REBOOT_MAGIC2, 0xd000fce2)
-
-(Thanks to Peter Osterlund:)
-
-#include <unistd.h>
-#include <syscall.h>
-
-#define LINUX_REBOOT_MAGIC1     0xfee1dead
-#define LINUX_REBOOT_MAGIC2     672274793
-#define LINUX_REBOOT_CMD_SW_SUSPEND     0xD000FCE2
-
-int main()
-{
-    syscall(SYS_reboot, LINUX_REBOOT_MAGIC1, LINUX_REBOOT_MAGIC2,
-            LINUX_REBOOT_CMD_SW_SUSPEND, 0);
-    return 0;
-}
-
-Also /sys/ interface should be still present.
-
 Q: What is 'suspend2'?
 
 A: suspend2 is 'Software Suspend 2', a forked implementation of
@@ -311,3 +286,46 @@ As a rule of thumb use encrypted swap to protect your data while your
 system is shut down or suspended. Additionally use the encrypted
 suspend image to prevent sensitive data from being stolen after
 resume.
+
+Q: Why can't we suspend to a swap file?
+
+A: Because accessing swap file needs the filesystem mounted, and
+filesystem might do something wrong (like replaying the journal)
+during mount.
+
+There are few ways to get that fixed:
+
+1) Probably could be solved by modifying every filesystem to support
+some kind of "really read-only!" option. Patches welcome.
+
+2) suspend2 gets around that by storing absolute positions in on-disk
+image (and blocksize), with resume parameter pointing directly to
+suspend header.
+
+Q: Is there a maximum system RAM size that is supported by swsusp?
+
+A: It should work okay with highmem.
+
+Q: Does swsusp (to disk) use only one swap partition or can it use
+multiple swap partitions (aggregate them into one logical space)?
+
+A: Only one swap partition, sorry.
+
+Q: If my application(s) causes lots of memory & swap space to be used
+(over half of the total system RAM), is it correct that it is likely
+to be useless to try to suspend to disk while that app is running?
+
+A: No, it should work okay, as long as your app does not mlock()
+it. Just prepare big enough swap partition.
+
+Q: What information is usefull for debugging suspend-to-disk problems?
+
+A: Well, last messages on the screen are always useful. If something
+is broken, it is usually some kernel driver, therefore trying with as
+little as possible modules loaded helps a lot. I also prefer people to
+suspend from console, preferably without X running. Booting with
+init=/bin/bash, then swapon and starting suspend sequence manually
+usually does the trick. Then it is good idea to try with latest
+vanilla kernel.
+
+
diff --git a/Documentation/power/video.txt b/Documentation/power/video.txt
index 7a4a5036d12..526d6dd267e 100644
--- a/Documentation/power/video.txt
+++ b/Documentation/power/video.txt
@@ -46,6 +46,12 @@ There are a few types of systems where video works after S3 resume:
   POSTing bios works. Ole Rohne has patch to do just that at
   http://dev.gentoo.org/~marineam/patch-radeonfb-2.6.11-rc2-mm2.
 
+(8) on some systems, you can use the video_post utility mentioned here:
+  http://bugzilla.kernel.org/show_bug.cgi?id=3670. Do echo 3 > /sys/power/state
+  && /usr/sbin/video_post - which will initialize the display in console mode.
+  If  you are in X, you can switch to a virtual terminal and back to X using
+  CTRL+ALT+F1 - CTRL+ALT+F7 to get the display working in graphical mode again.
+
 Now, if you pass acpi_sleep=something, and it does not work with your
 bios, you'll get a hard crash during resume. Be careful. Also it is
 safest to do your experiments with plain old VGA console. The vesafb
@@ -64,7 +70,8 @@ Model                           hack (or "how to do it")
 ------------------------------------------------------------------------------
 Acer Aspire 1406LC		ole's late BIOS init (7), turn off DRI
 Acer TM 242FX			vbetool (6)
-Acer TM C300                    vga=normal (only suspend on console, not in X), vbetool (6)
+Acer TM C110			video_post (8)
+Acer TM C300                    vga=normal (only suspend on console, not in X), vbetool (6) or video_post (8)
 Acer TM 4052LCi		        s3_bios (2)
 Acer TM 636Lci			s3_bios vga=normal (2)
 Acer TM 650 (Radeon M7)		vga=normal plus boot-radeon (5) gets text console back
@@ -113,6 +120,7 @@ IBM ThinkPad T42p (2373-GTG)	s3_bios (2)
 IBM TP X20			??? (*)
 IBM TP X30			s3_bios (2)
 IBM TP X31 / Type 2672-XXH      none (1), use radeontool (http://fdd.com/software/radeon/) to turn off backlight.
+IBM TP X32			none (1), but backlight is on and video is trashed after long suspend
 IBM Thinkpad X40 Type 2371-7JG  s3_bios,s3_mode (4)
 Medion MD4220			??? (*)
 Samsung P35			vbetool needed (6)
diff --git a/Documentation/scsi/aic7xxx.txt b/Documentation/scsi/aic7xxx.txt
index 160e7354cd1..47e74ddc4bc 100644
--- a/Documentation/scsi/aic7xxx.txt
+++ b/Documentation/scsi/aic7xxx.txt
@@ -1,5 +1,5 @@
 ====================================================================
-=    Adaptec Aic7xxx Fast -> Ultra160 Family Manager Set v6.2.28   =
+=    Adaptec Aic7xxx Fast -> Ultra160 Family Manager Set v7.0      =
 =                            README for                            =
 =                     The Linux Operating System                   =
 ====================================================================
@@ -131,6 +131,10 @@ The following information is available in this file:
       SCSI "stub" effects.
 
 2. Version History
+   7.0	  (4th August, 2005)
+	- Updated driver to use SCSI transport class infrastructure
+	- Upported sequencer and core fixes from last adaptec released
+	  version of the driver.
    6.2.36 (June 3rd, 2003)
         - Correct code that disables PCI parity error checking.
         - Correct and simplify handling of the ignore wide residue
diff --git a/Documentation/scsi/scsi_mid_low_api.txt b/Documentation/scsi/scsi_mid_low_api.txt
index 7536823c0cb..44df89c9c04 100644
--- a/Documentation/scsi/scsi_mid_low_api.txt
+++ b/Documentation/scsi/scsi_mid_low_api.txt
@@ -373,13 +373,11 @@ Summary:
    scsi_activate_tcq - turn on tag command queueing
    scsi_add_device - creates new scsi device (lu) instance
    scsi_add_host - perform sysfs registration and SCSI bus scan.
-   scsi_add_timer - (re-)start timer on a SCSI command.
    scsi_adjust_queue_depth - change the queue depth on a SCSI device
    scsi_assign_lock - replace default host_lock with given lock
    scsi_bios_ptable - return copy of block device's partition table
    scsi_block_requests - prevent further commands being queued to given host
    scsi_deactivate_tcq - turn off tag command queueing
-   scsi_delete_timer - cancel timer on a SCSI command.
    scsi_host_alloc - return a new scsi_host instance whose refcount==1
    scsi_host_get - increments Scsi_Host instance's refcount
    scsi_host_put - decrements Scsi_Host instance's refcount (free if 0)
@@ -458,27 +456,6 @@ int scsi_add_host(struct Scsi_Host *shost, struct device * dev)
 
 
 /**
- * scsi_add_timer - (re-)start timer on a SCSI command.
- * @scmd:    pointer to scsi command instance
- * @timeout: duration of timeout in "jiffies"
- * @complete: pointer to function to call if timeout expires
- *
- *      Returns nothing
- *
- *      Might block: no
- *
- *      Notes: Each scsi command has its own timer, and as it is added
- *      to the queue, we set up the timer. When the command completes, 
- *      we cancel the timer. An LLD can use this function to change
- *      the existing timeout value.
- *
- *      Defined in: drivers/scsi/scsi_error.c
- **/
-void scsi_add_timer(struct scsi_cmnd *scmd, int timeout, 
-                    void (*complete)(struct scsi_cmnd *))
-
-
-/**
  * scsi_adjust_queue_depth - allow LLD to change queue depth on a SCSI device
  * @sdev:       pointer to SCSI device to change queue depth on
  * @tagged:     0 - no tagged queuing
@@ -566,24 +543,6 @@ void scsi_deactivate_tcq(struct scsi_device *sdev, int depth)
 
 
 /**
- * scsi_delete_timer - cancel timer on a SCSI command.
- * @scmd:    pointer to scsi command instance
- *
- *      Returns 1 if able to cancel timer else 0 (i.e. too late or already
- *      cancelled).
- *
- *      Might block: no [may in the future if it invokes del_timer_sync()]
- *
- *      Notes: All commands issued by upper levels already have a timeout
- *      associated with them. An LLD can use this function to cancel the
- *      timer.
- *
- *      Defined in: drivers/scsi/scsi_error.c
- **/
-int scsi_delete_timer(struct scsi_cmnd *scmd)
-
-
-/**
  * scsi_host_alloc - create a scsi host adapter instance and perform basic
  *                   initialization.
  * @sht:        pointer to scsi host template
diff --git a/Documentation/sonypi.txt b/Documentation/sonypi.txt
index 0f3b2405d09..c1237a92550 100644
--- a/Documentation/sonypi.txt
+++ b/Documentation/sonypi.txt
@@ -99,6 +99,7 @@ statically linked into the kernel). Those options are:
 				SONYPI_MEYE_MASK		0x0400
 				SONYPI_MEMORYSTICK_MASK		0x0800
 				SONYPI_BATTERY_MASK		0x1000
+				SONYPI_WIRELESS_MASK		0x2000
 
 	useinput:	if set (which is the default) two input devices are
 			created, one which interprets the jogdial events as
@@ -137,6 +138,15 @@ Bugs:
 	  speed handling etc). Use ACPI instead of APM if it works on your
 	  laptop.
 
+	- sonypi lacks the ability to distinguish between certain key
+	  events on some models.
+
+	- some models with the nvidia card (geforce go 6200 tc) uses a
+	  different way to adjust the backlighting of the screen. There
+	  is a userspace utility to adjust the brightness on those models,
+	  which can be downloaded from
+	  http://www.acc.umu.se/~erikw/program/smartdimmer-0.1.tar.bz2
+
 	- since all development was done by reverse engineering, there is
 	  _absolutely no guarantee_ that this driver will not crash your
 	  laptop. Permanently.
diff --git a/Documentation/vm/locking b/Documentation/vm/locking
index c3ef09ae3bb..f366fa95617 100644
--- a/Documentation/vm/locking
+++ b/Documentation/vm/locking
@@ -83,19 +83,18 @@ single address space optimization, so that the zap_page_range (from
 vmtruncate) does not lose sending ipi's to cloned threads that might 
 be spawned underneath it and go to user mode to drag in pte's into tlbs.
 
-swap_list_lock/swap_device_lock
--------------------------------
+swap_lock
+--------------
 The swap devices are chained in priority order from the "swap_list" header. 
 The "swap_list" is used for the round-robin swaphandle allocation strategy.
 The #free swaphandles is maintained in "nr_swap_pages". These two together
-are protected by the swap_list_lock. 
+are protected by the swap_lock.
 
-The swap_device_lock, which is per swap device, protects the reference 
-counts on the corresponding swaphandles, maintained in the "swap_map"
-array, and the "highest_bit" and "lowest_bit" fields.
+The swap_lock also protects all the device reference counts on the
+corresponding swaphandles, maintained in the "swap_map" array, and the
+"highest_bit" and "lowest_bit" fields.
 
-Both of these are spinlocks, and are never acquired from intr level. The
-locking hierarchy is swap_list_lock -> swap_device_lock.
+The swap_lock is a spinlock, and is never acquired from intr level.
 
 To prevent races between swap space deletion or async readahead swapins
 deciding whether a swap handle is being used, ie worthy of being read in
diff --git a/Documentation/watchdog/watchdog-api.txt b/Documentation/watchdog/watchdog-api.txt
index 28388aa700c..c5beb548cfc 100644
--- a/Documentation/watchdog/watchdog-api.txt
+++ b/Documentation/watchdog/watchdog-api.txt
@@ -228,6 +228,26 @@ advantechwdt.c -- Advantech Single Board Computer
 	The GETSTATUS call returns if the device is open or not.
 	[FIXME -- silliness again?]
 	
+booke_wdt.c -- PowerPC BookE Watchdog Timer
+
+	Timeout default varies according to frequency, supports
+	SETTIMEOUT
+
+	Watchdog can not be turned off, CONFIG_WATCHDOG_NOWAYOUT
+	does not make sense
+
+	GETSUPPORT returns the watchdog_info struct, and
+	GETSTATUS returns the supported options. GETBOOTSTATUS
+	returns a 1 if the last reset was caused by the
+	watchdog and a 0 otherwise. This watchdog can not be
+	disabled once it has been started. The wdt_period kernel
+	parameter selects which bit of the time base changing
+	from 0->1 will trigger the watchdog exception. Changing
+	the timeout from the ioctl calls will change the
+	wdt_period as defined above. Finally if you would like to
+	replace the default Watchdog Handler you can implement the
+	WatchdogHandler() function in your own code.
+
 eurotechwdt.c -- Eurotech CPU-1220/1410
 
 	The timeout can be set using the SETTIMEOUT ioctl and defaults