diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
7 files changed, 87 insertions, 94 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt index cc2608021f26..ce1b2231bf5d 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt @@ -1,7 +1,9 @@ * Generic 8-bits shift register GPIO driver Required properties: -- compatible : Should be "fairchild,74hc595" +- compatible: Should contain one of the following: + "fairchild,74hc595" + "nxp,74lvc594" - reg : chip select number - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be two. The first cell is the pin number and diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index 120bc4971cf3..4b6cc632ca5c 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -1,9 +1,10 @@ -* Freescale MPC512x/MPC8xxx/Layerscape GPIO controller +* Freescale MPC512x/MPC8xxx/QorIQ/Layerscape GPIO controller Required properties: - compatible : Should be "fsl,<soc>-gpio" The following <soc>s are known to be supported: - mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq. + mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq, + ls1021a, ls1043a, ls2080a. - reg : Address and length of the register set for the device - interrupts : Should be the port interrupt shared by all 32 pins. - #gpio-cells : Should be two. The first cell is the pin number and @@ -15,7 +16,7 @@ Optional properties: - little-endian : GPIO registers are used as little endian. If not present registers are used as big endian by default. -Example: +Example of gpio-controller node for a mpc5125 SoC: gpio0: gpio@1100 { compatible = "fsl,mpc5125-gpio"; @@ -24,3 +25,16 @@ gpio0: gpio@1100 { interrupts = <78 0x8>; status = "okay"; }; + +Example of gpio-controller node for a ls2080a SoC: + +gpio0: gpio@2300000 { + compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt deleted file mode 100644 index d4eab9227ea4..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt +++ /dev/null @@ -1,36 +0,0 @@ -Driver a GPIO line that can be used to turn the power off. - -The driver supports both level triggered and edge triggered power off. -At driver load time, the driver will request the given gpio line and -install a pm_power_off handler. If the optional properties 'input' is -not found, the GPIO line will be driven in the inactive -state. Otherwise its configured as an input. - -When the pm_power_off is called, the gpio is configured as an output, -and drive active, so triggering a level triggered power off -condition. This will also cause an inactive->active edge condition, so -triggering positive edge triggered power off. After a delay of 100ms, -the GPIO is set to inactive, thus causing an active->inactive edge, -triggering negative edge triggered power off. After another 100ms -delay the GPIO is driver active again. If the power is still on and -the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. - -Required properties: -- compatible : should be "gpio-poweroff". -- gpios : The GPIO to set high/low, see "gpios property" in - Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be - low to power down the board set it to "Active Low", otherwise set - gpio to "Active High". - -Optional properties: -- input : Initially configure the GPIO line as an input. Only reconfigure - it to an output when the pm_power_off function is called. If this optional - property is not specified, the GPIO is initialized as an output in its - inactive state. - -Examples: - -gpio-poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio 4 0>; -}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-restart.txt b/Documentation/devicetree/bindings/gpio/gpio-restart.txt deleted file mode 100644 index af3701bc15c4..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-restart.txt +++ /dev/null @@ -1,54 +0,0 @@ -Drive a GPIO line that can be used to restart the system from a restart -handler. - -This binding supports level and edge triggered reset. At driver load -time, the driver will request the given gpio line and install a restart -handler. If the optional properties 'open-source' is not found, the GPIO line -will be driven in the inactive state. Otherwise its not driven until -the restart is initiated. - -When the system is restarted, the restart handler will be invoked in -priority order. The gpio is configured as an output, and driven active, -triggering a level triggered reset condition. This will also cause an -inactive->active edge condition, triggering positive edge triggered -reset. After a delay specified by active-delay, the GPIO is set to -inactive, thus causing an active->inactive edge, triggering negative edge -triggered reset. After a delay specified by inactive-delay, the GPIO -is driven active again. After a delay specified by wait-delay, the -restart handler completes allowing other restart handlers to be attempted. - -Required properties: -- compatible : should be "gpio-restart". -- gpios : The GPIO to set high/low, see "gpios property" in - Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be - low to reset the board set it to "Active Low", otherwise set - gpio to "Active High". - -Optional properties: -- open-source : Treat the GPIO as being open source and defer driving - it to when the restart is initiated. If this optional property is not - specified, the GPIO is initialized as an output in its inactive state. -- priority : A priority ranging from 0 to 255 (default 128) according to - the following guidelines: - 0: Restart handler of last resort, with limited restart - capabilities - 128: Default restart handler; use if no other restart handler is - expected to be available, and/or if restart functionality is - sufficient to restart the entire system - 255: Highest priority restart handler, will preempt all other - restart handlers -- active-delay: Delay (default 100) to wait after driving gpio active [ms] -- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms] -- wait-delay: Delay (default 3000) to wait after completing restart - sequence [ms] - -Examples: - -gpio-restart { - compatible = "gpio-restart"; - gpios = <&gpio 4 0>; - priority = <128>; - active-delay = <100>; - inactive-delay = <100>; - wait-delay = <3000>; -}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt index 262ee4ddf2cb..28662d83a43e 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt @@ -3,6 +3,8 @@ Netlogic XLP Family GPIO This GPIO driver is used for following Netlogic XLP SoCs: XLP832, XLP316, XLP208, XLP980, XLP532 +This GPIO driver is also compatible with GPIO controller found on +Broadcom Vulcan ARM64. Required properties: ------------------- @@ -13,6 +15,7 @@ Required properties: - "netlogic,xlp208-gpio": For Netlogic XLP208 - "netlogic,xlp980-gpio": For Netlogic XLP980 - "netlogic,xlp532-gpio": For Netlogic XLP532 + - "brcm,vulcan-gpio": For Broadcom Vulcan ARM64 - reg: Physical base address and length of the controller's registers. - #gpio-cells: Should be two. The first cell is the pin number and the second cell is used to specify optional parameters (currently unused). diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 069cdf6f9dac..68d28f62a6f4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -131,6 +131,13 @@ Every GPIO controller node must contain both an empty "gpio-controller" property, and a #gpio-cells integer property, which indicates the number of cells in a gpio-specifier. +Some system-on-chips (SoCs) use the concept of GPIO banks. A GPIO bank is an +instance of a hardware IP core on a silicon die, usually exposed to the +programmer as a coherent range of I/O addresses. Usually each such bank is +exposed in the device tree as an individual gpio-controller node, reflecting +the fact that the hardware was synthesized by reusing the same IP block a +few times over. + Optionally, a GPIO controller may have a "ngpios" property. This property indicates the number of in-use slots of available slots for GPIOs. The typical example is something like this: the hardware register is 32 bits @@ -145,6 +152,21 @@ additional bitmask is needed to specify which GPIOs are actually in use, and which are dummies. The bindings for this case has not yet been specified, but should be specified if/when such hardware appears. +Optionally, a GPIO controller may have a "gpio-line-names" property. This is +an array of strings defining the names of the GPIO lines going out of the +GPIO controller. This name should be the most meaningful producer name +for the system, such as a rail name indicating the usage. Package names +such as pin name are discouraged: such lines have opaque names (since they +are by definition generic purpose) and such names are usually not very +helpful. For example "MMC-CD", "Red LED Vdd" and "ethernet reset" are +reasonable line names as they describe what the line is used for. "GPIO0" +is not a good name to give to a GPIO line. Placeholders are discouraged: +rather use the "" (blank string) if the use of the GPIO line is undefined +in your design. The names are assigned starting from line offset 0 from +left to right from the passed array. An incomplete array (where the number +of passed named are less than ngpios) will still be used up until the last +provided valid line index. + Example: gpio-controller@00000000 { @@ -153,6 +175,10 @@ gpio-controller@00000000 { gpio-controller; #gpio-cells = <2>; ngpios = <18>; + gpio-line-names = "MMC-CD", "MMC-WP", "VDD eth", "RST eth", "LED R", + "LED G", "LED B", "Col A", "Col B", "Col C", "Col D", + "Row A", "Row B", "Row C", "Row D", "NMI button", + "poweroff", "reset"; } The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism diff --git a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt new file mode 100644 index 000000000000..038c3a6a1f4d --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt @@ -0,0 +1,38 @@ +Bindings for the Western Digital's MyBook Live memory-mapped GPIO controllers. + +The Western Digital MyBook Live has two memory-mapped GPIO controllers. +Both GPIO controller only have a single 8-bit data register, where GPIO +state can be read and/or written. + +Required properties: + - compatible: should be "wd,mbl-gpio" + - reg-names: must contain + "dat" - data register + - reg: address + size pairs describing the GPIO register sets; + order must correspond with the order of entries in reg-names + - #gpio-cells: must be set to 2. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + - gpio-controller: Marks the device node as a gpio controller. + +Optional properties: + - no-output: GPIOs are read-only. + +Examples: + gpio0: gpio0@e0000000 { + compatible = "wd,mbl-gpio"; + reg-names = "dat"; + reg = <0xe0000000 0x1>; + #gpio-cells = <2>; + gpio-controller; + }; + + gpio1: gpio1@e0100000 { + compatible = "wd,mbl-gpio"; + reg-names = "dat"; + reg = <0xe0100000 0x1>; + #gpio-cells = <2>; + gpio-controller; + no-output; + }; |