1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
|
#include <common.h>
#include <mpc8xx.h>
#include <pcmcia.h>
#include "csr.h"
#undef CONFIG_PCMCIA
#if defined(CONFIG_CMD_PCMCIA)
#define CONFIG_PCMCIA
#endif
#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
#define CONFIG_PCMCIA
#endif
#ifdef CONFIG_PCMCIA
/* A lot of this has been taken from the RPX code in this file it works from me.
I have added the voltage selection for the MBX board. */
/* MBX voltage bit in control register #2 */
#define CR2_VPP12 ((uchar)0x10)
#define CR2_VPPVDD ((uchar)0x20)
#define CR2_VDD5 ((uchar)0x40)
#define CR2_VDD3 ((uchar)0x80)
#define PCMCIA_BOARD_MSG "MBX860"
int pcmcia_voltage_set (int slot, int vcc, int vpp)
{
uchar reg = 0;
debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
switch (vcc) {
case 0:
break;
case 33:
reg |= CR2_VDD3;
break;
case 50:
reg |= CR2_VDD5;
break;
default:
return 1;
}
switch (vpp) {
case 0:
break;
case 33:
case 50:
if (vcc == vpp) {
reg |= CR2_VPPVDD;
} else {
return 1;
}
break;
case 120:
reg |= CR2_VPP12;
break;
default:
return 1;
}
/* first, turn off all power */
MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
/* enable new powersettings */
MBX_CSR2 |= reg;
debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
return (0);
}
int pcmcia_hardware_enable (int slot)
{
volatile immap_t *immap;
volatile cpm8xx_t *cp;
volatile pcmconf8xx_t *pcmp;
volatile sysconf8xx_t *sysp;
uint reg, mask;
debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
'A' + slot);
udelay (10000);
immap = (immap_t *) CFG_IMMR;
sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
/* clear interrupt state, and disable interrupts */
pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
/*
* Disable interrupts, DMA, and PCMCIA buffers
* (isolate the interface) and assert RESET signal
*/
debug ("Disable PCMCIA buffers and assert RESET\n");
reg = 0;
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
PCMCIA_PGCRX (_slot_) = reg;
udelay (500);
/* remove all power */
pcmcia_voltage_set (slot, 0, 0);
/*
* Make sure there is a card in the slot, then configure the interface.
*/
udelay(10000);
debug ("[%d] %s: PIPR(%p)=0x%x\n",
__LINE__,__FUNCTION__,
&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
#ifndef CONFIG_HMI10
if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
#else
if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
#endif /* CONFIG_HMI10 */
printf (" No Card found\n");
return (1);
}
/*
* Power On.
*/
mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
reg = pcmp->pcmc_pipr;
debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
(reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
(reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
if ((reg & mask) == mask) {
pcmcia_voltage_set (_slot_, 50, 0);
printf (" 5.0V card found: ");
} else {
pcmcia_voltage_set (_slot_, 33, 0);
printf (" 3.3V card found: ");
}
debug ("Enable PCMCIA buffers and stop RESET\n");
reg = PCMCIA_PGCRX (_slot_);
reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
PCMCIA_PGCRX (_slot_) = reg;
udelay (250000); /* some cards need >150 ms to come up :-( */
debug ("# hardware_enable done\n");
return (0);
}
#if defined(CONFIG_CMD_PCMCIA)
int pcmcia_hardware_disable (int slot)
{
return 0; /* No hardware to disable */
}
#endif
#endif /* CONFIG_PCMCIA */
|
