Initial revision

1 files changed, 263 insertions, 0 deletions

diff --git a/include/status_led.h b/include/status_led.h
new file mode 100644
index 0000000000..9b2de3ebed
--- /dev/null
+++ b/include/status_led.h
@@ -0,0 +1,263 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * The purpose of this code is to signal the operational status of a
+ * target which usually boots over the network; while running in
+ * PCBoot, a status LED is blinking. As soon as a valid BOOTP reply
+ * message has been received, the LED is turned off. The Linux
+ * kernel, once it is running, will start blinking the LED again,
+ * with another frequency.
+ */
+
+#ifndef _STATUS_LED_H_
+#define	_STATUS_LED_H_
+
+#ifdef CONFIG_STATUS_LED
+
+#define STATUS_LED_OFF		0
+#define STATUS_LED_BLINKING	1
+#define STATUS_LED_ON		2
+
+void status_led_tick (unsigned long timestamp);
+void status_led_set  (int led, int state);
+
+/*****  TQM8xxL  ********************************************************/
+#if defined(CONFIG_TQM8xxL)
+# define STATUS_LED_PAR		im_cpm.cp_pbpar
+# define STATUS_LED_DIR		im_cpm.cp_pbdir
+# define STATUS_LED_ODR		im_cpm.cp_pbodr
+# define STATUS_LED_DAT		im_cpm.cp_pbdat
+
+# define STATUS_LED_BIT		0x00000001
+# define STATUS_LED_PERIOD	(CFG_HZ / 2)
+# define STATUS_LED_STATE	STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE	1		/* LED on for bit == 1	*/
+
+# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
+
+/*****  MVS v1  **********************************************************/
+#elif (defined(CONFIG_MVS) && CONFIG_MVS < 2)
+# define STATUS_LED_PAR		im_ioport.iop_pdpar
+# define STATUS_LED_DIR		im_ioport.iop_pddir
+# undef  STATUS_LED_ODR
+# define STATUS_LED_DAT		im_ioport.iop_pddat
+
+# define STATUS_LED_BIT		0x00000001
+# define STATUS_LED_PERIOD	(CFG_HZ / 2)
+# define STATUS_LED_STATE	STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE	1		/* LED on for bit == 1	*/
+
+# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
+
+/*****  ETX_094  ********************************************************/
+#elif defined(CONFIG_ETX094)
+
+# define STATUS_LED_PAR		im_ioport.iop_pdpar
+# define STATUS_LED_DIR		im_ioport.iop_pddir
+# undef  STATUS_LED_ODR
+# define STATUS_LED_DAT		im_ioport.iop_pddat
+
+# define STATUS_LED_BIT		0x00000001
+# define STATUS_LED_PERIOD	(CFG_HZ / 2)
+# define STATUS_LED_STATE	STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE	0		/* LED on for bit == 0	*/
+
+# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
+
+/*****  GEN860T  *********************************************************/
+#elif defined(CONFIG_GEN860T)
+
+# define STATUS_LED_PAR			im_ioport.iop_papar
+# define STATUS_LED_DIR			im_ioport.iop_padir
+# define STATUS_LED_ODR			im_ioport.iop_paodr
+# define STATUS_LED_DAT			im_ioport.iop_padat
+
+# define STATUS_LED_BIT			0x0800	/* Red LED 0 is on PA.4	*/
+# define STATUS_LED_PERIOD		(CFG_HZ / 2)
+# define STATUS_LED_STATE		STATUS_LED_BLINKING
+# define STATUS_LED_BIT1		0x0400	/* Grn LED 1 is on PA.5	*/
+# define STATUS_LED_PERIOD1		(CFG_HZ / 2)
+# define STATUS_LED_STATE1		STATUS_LED_BLINKING
+# define STATUS_LED_BIT2		0x0080	/* Red LED 2 is on PA.8	*/
+# define STATUS_LED_PERIOD2		(CFG_HZ / 2)
+# define STATUS_LED_STATE2		STATUS_LED_BLINKING
+# define STATUS_LED_BIT3		0x0040	/* Grn LED 3 is on PA.9	*/
+# define STATUS_LED_PERIOD3		(CFG_HZ / 2)
+# define STATUS_LED_STATE3		STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE		1	/* LED on for bit == 1	*/
+# define STATUS_LED_BOOT		0	/* Boot status on LED 1	*/
+
+/*****  IVMS8  **********************************************************/
+#elif defined(CONFIG_IVMS8)
+
+# define STATUS_LED_PAR		im_cpm.cp_pbpar
+# define STATUS_LED_DIR		im_cpm.cp_pbdir
+# define STATUS_LED_ODR		im_cpm.cp_pbodr
+# define STATUS_LED_DAT		im_cpm.cp_pbdat
+
+# define STATUS_LED_BIT		0x00000010	/* LED 0 is on PB.27	*/
+# define STATUS_LED_PERIOD	(1 * CFG_HZ)
+# define STATUS_LED_STATE	STATUS_LED_OFF
+# define STATUS_LED_BIT1	0x00000020	/* LED 1 is on PB.26	*/
+# define STATUS_LED_PERIOD1	(1 * CFG_HZ)
+# define STATUS_LED_STATE1	STATUS_LED_OFF
+/* IDE LED usable for other purposes, too */
+# define STATUS_LED_BIT2	0x00000008	/* LED 2 is on PB.28	*/
+# define STATUS_LED_PERIOD2	(1 * CFG_HZ)
+# define STATUS_LED_STATE2	STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE	1		/* LED on for bit == 1	*/
+
+# define STATUS_ILOCK_SWITCH	0x00800000	/* ILOCK switch in IRQ4	*/
+
+# define STATUS_ILOCK_PERIOD	(CFG_HZ / 10)	/* about every 100 ms	*/
+
+# define STATUS_LED_YELLOW	0
+# define STATUS_LED_GREEN	1
+# define STATUS_LED_BOOT	2		/* IDE LED used for boot status */
+
+/*****  IVML24  *********************************************************/
+#elif defined(CONFIG_IVML24)
+
+# define STATUS_LED_PAR		im_cpm.cp_pbpar
+# define STATUS_LED_DIR		im_cpm.cp_pbdir
+# define STATUS_LED_ODR		im_cpm.cp_pbodr
+# define STATUS_LED_DAT		im_cpm.cp_pbdat
+
+# define STATUS_LED_BIT		0x00000010	/* LED 0 is on PB.27	*/
+# define STATUS_LED_PERIOD	(1 * CFG_HZ)
+# define STATUS_LED_STATE	STATUS_LED_OFF
+# define STATUS_LED_BIT1	0x00000020	/* LED 1 is on PB.26	*/
+# define STATUS_LED_PERIOD1	(1 * CFG_HZ)
+# define STATUS_LED_STATE1	STATUS_LED_OFF
+/* IDE LED usable for other purposes, too */
+# define STATUS_LED_BIT2	0x00000008	/* LED 2 is on PB.28	*/
+# define STATUS_LED_PERIOD2	(1 * CFG_HZ)
+# define STATUS_LED_STATE2	STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE	1		/* LED on for bit == 1	*/
+
+# define STATUS_ILOCK_SWITCH	0x00004000	/* ILOCK is on PB.17	*/
+
+# define STATUS_ILOCK_PERIOD	(CFG_HZ / 10)	/* about every 100 ms	*/
+
+# define STATUS_LED_YELLOW	0
+# define STATUS_LED_GREEN	1
+# define STATUS_LED_BOOT	2		/* IDE LED used for boot status */
+
+/*****  LANTEC  *********************************************************/
+#elif defined(CONFIG_LANTEC)
+
+# define STATUS_LED_PAR		im_ioport.iop_pdpar
+# define STATUS_LED_DIR		im_ioport.iop_pddir
+# undef  STATUS_LED_ODR
+# define STATUS_LED_DAT		im_ioport.iop_pddat
+
+# if CONFIG_LATEC < 2
+#  define STATUS_LED_BIT	0x1000
+# else
+#  define STATUS_LED_BIT	0x0800
+# endif
+# define STATUS_LED_PERIOD	(CFG_HZ / 2)
+# define STATUS_LED_STATE	STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE	0		/* LED on for bit == 0 */
+
+# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
+
+/*****  PCU E  and  CCM  ************************************************/
+#elif (defined(CONFIG_PCU_E) || defined(CONFIG_CCM))
+
+# define STATUS_LED_PAR		im_cpm.cp_pbpar
+# define STATUS_LED_DIR		im_cpm.cp_pbdir
+# define STATUS_LED_ODR		im_cpm.cp_pbodr
+# define STATUS_LED_DAT		im_cpm.cp_pbdat
+
+# define STATUS_LED_BIT		0x00010000	/* green LED is on PB.15 */
+# define STATUS_LED_PERIOD	(CFG_HZ / 2)
+# define STATUS_LED_STATE	STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE	1		/* LED on for bit == 1 */
+
+# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
+
+/*****  ICU862   ********************************************************/
+#elif defined(CONFIG_ICU862)
+
+# define STATUS_LED_PAR		im_ioport.iop_papar
+# define STATUS_LED_DIR		im_ioport.iop_padir
+# define STATUS_LED_ODR		im_ioport.iop_paodr
+# define STATUS_LED_DAT		im_ioport.iop_padat
+
+# define STATUS_LED_BIT		0x4000		/* LED 0 is on PA.1 */
+# define STATUS_LED_PERIOD	(CFG_HZ / 2)
+# define STATUS_LED_STATE	STATUS_LED_BLINKING
+# define STATUS_LED_BIT1	0x1000		/* LED 1 is on PA.3 */
+# define STATUS_LED_PERIOD1	(CFG_HZ)
+# define STATUS_LED_STATE1	STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE	1		/* LED on for bit == 1	*/
+
+# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
+
+/*****  Someone else defines these  *************************************/
+#elif defined(STATUS_LED_PAR)
+
+  /*
+   * ADVICE: Define in your board configuration file rather than
+   * filling this file up with lots of custom board stuff.
+   */
+
+/*****  NetVia   ********************************************************/
+#elif defined(CONFIG_NETVIA)
+
+#define STATUS_LED_PAR		im_ioport.iop_pdpar
+#define STATUS_LED_DIR		im_ioport.iop_pddir
+#undef  STATUS_LED_ODR
+#define STATUS_LED_DAT		im_ioport.iop_pddat
+
+# define STATUS_LED_BIT		0x0080			/* PD.8 */
+# define STATUS_LED_PERIOD	(CFG_HZ / 2)
+# define STATUS_LED_STATE	STATUS_LED_BLINKING
+
+# define STATUS_LED_BIT1	0x0040			/* PD.9 */
+# define STATUS_LED_PERIOD1	(CFG_HZ / 2)
+# define STATUS_LED_STATE1	STATUS_LED_OFF
+
+# define STATUS_LED_ACTIVE	0		/* LED on for bit == 0	*/
+# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
+
+/************************************************************************/
+#else
+# error Status LED configuration missing
+#endif
+/************************************************************************/
+
+#endif	/* CONFIG_STATUS_LED	*/
+
+#endif	/* _STATUS_LED_H_	*/