powerpc: remove icecube_5200, Lite5200, cpci5200, mecp5200, pf5200

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>

1 files changed, 0 insertions, 403 deletions

diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h
deleted file mode 100644
index 1861aa86d9..0000000000
--- a/include/configs/IceCube.h
+++ /dev/null
@@ -1,403 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200		1	/* This is a MPC5200 CPU */
-#define CONFIG_ICECUBE		1	/* ... on IceCube board */
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFFF00000	boot high (standard configuration)
- * 0xFF000000	boot low for 16 MiB boards
- * 0xFF800000	boot low for  8 MiB boards
- * 0x00100000	boot from RAM (for testing only)
- */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#define CONFIG_PCI
-
-#if defined(CONFIG_PCI)
-#define CONFIG_PCI_PNP		1
-#define CONFIG_PCI_SCAN_SHOW	1
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1
-
-#define CONFIG_PCI_MEM_BUS	0x40000000
-#define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE	0x10000000
-
-#define CONFIG_PCI_IO_BUS	0x50000000
-#define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE	0x01000000
-#endif
-
-#define CONFIG_SYS_XLB_PIPELINING	1
-
-#define CONFIG_MII		1
-#define CONFIG_EEPRO100		1
-#define CONFIG_SYS_RX_ETH_BUFFER	8  /* use 8 rx buffer on eepro100  */
-#define CONFIG_NS8382X		1
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-/* USB */
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
-#define CONFIG_SYS_OHCI_BE_CONTROLLER
-#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
-#define CONFIG_SYS_USB_OHCI_CPU_INIT	1
-#define CONFIG_SYS_USB_OHCI_REGS_BASE	MPC5XXX_USB
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"mpc5200"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	15
-
-#define	CONFIG_TIMESTAMP		/* Print image info with timestamp */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#endif
-
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFF000000)		/* Boot low with 16 MB Flash */
-#   define CONFIG_SYS_LOWBOOT	        1
-#   define CONFIG_SYS_LOWBOOT16	1
-#endif
-#if (CONFIG_SYS_TEXT_BASE == 0xFF800000)		/* Boot low with  8 MB Flash */
-#if defined(CONFIG_LITE5200B)
-#   error CONFIG_SYS_LOWBOOT08 is incompatible with the Lite5200B
-#else
-#   define CONFIG_SYS_LOWBOOT	        1
-#   define CONFIG_SYS_LOWBOOT08	1
-#endif
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_82xx\0"					\
-	"bootfile=/tftpboot/MPC5200/uImage\0"				\
-	""
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-/*
- * IPB Bus clocking configuration.
- */
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK	/* define for 133MHz speed */
-#else
-#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU			"PowerPC,5200@0"
-#define OF_SOC			"soc5200@f0000000"
-#define OF_TBCLK		(bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH		"/soc5200@f0000000/serial@2000"
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
-
-/*
- * Flash configuration
- */
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_SYS_FLASH_BASE		0xFE000000
-#define CONFIG_SYS_FLASH_SIZE		0x01000000
-#if !defined(CONFIG_SYS_LOWBOOT)
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x01760000 + 0x00800000)
-#else	/* CONFIG_SYS_LOWBOOT */
-#if defined(CONFIG_SYS_LOWBOOT08)
-# error CONFIG_SYS_LOWBOOT08 is incompatible with the Lite5200B
-#endif
-#if defined(CONFIG_SYS_LOWBOOT16)
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x01060000)
-#endif
-#endif /* CONFIG_SYS_LOWBOOT */
-#else /* !CONFIG_LITE5200B (IceCube)*/
-#define CONFIG_SYS_FLASH_BASE		0xFF000000
-#define CONFIG_SYS_FLASH_SIZE		0x01000000
-#if !defined(CONFIG_SYS_LOWBOOT)
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00740000 + 0x00800000)
-#else	/* CONFIG_SYS_LOWBOOT */
-#if defined(CONFIG_SYS_LOWBOOT08)
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00040000 + 0x00800000)
-#endif
-#if defined(CONFIG_SYS_LOWBOOT16)
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00040000)
-#endif
-#endif	/* CONFIG_SYS_LOWBOOT */
-#endif /* CONFIG_LITE5200B */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max num of memory banks      */
-
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
-
-#undef CONFIG_FLASH_16BIT	/* Flash is 8-bit */
-
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_CS1_START,CONFIG_SYS_CS0_START}
-#endif
-
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SIZE		0x10000
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#else
-#define CONFIG_ENV_SECT_SIZE	0x10000
-#endif
-#define CONFIG_ENV_OVERWRITE	1
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR		0xF0000000
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR	0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE	/* Size of used area in DPRAM */
-
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC	1
-#define CONFIG_MPC5xxx_FEC_MII100
-/*
- * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
- */
-/* #define CONFIG_MPC5xxx_FEC_MII10 */
-#define CONFIG_PHY_ADDR		0x00
-
-/*
- * GPIO configuration
- */
-#ifdef CONFIG_MPC5200_DDR
-#define CONFIG_SYS_GPS_PORT_CONFIG	0x90000004
-#else
-#define CONFIG_SYS_GPS_PORT_CONFIG	0x10000004
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL		HID0_ICE
-
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_SYS_CS1_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS1_SIZE		CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_CS1_CFG		0x00047800
-#define CONFIG_SYS_CS0_START		(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE)
-#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_CS0_START
-#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG		0x00047800
-#else /* IceCube aka Lite5200 */
-#ifdef CONFIG_MPC5200_DDR
-
-#define CONFIG_SYS_BOOTCS_START	(CONFIG_SYS_CS1_START + CONFIG_SYS_CS1_SIZE)
-#define CONFIG_SYS_BOOTCS_SIZE		0x00800000
-#define CONFIG_SYS_BOOTCS_CFG		0x00047801
-#define CONFIG_SYS_CS1_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS1_SIZE		0x00800000
-#define CONFIG_SYS_CS1_CFG		0x00047800
-
-#else /* !CONFIG_MPC5200_DDR */
-
-#define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG		0x00047801
-#define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
-
-#endif /* CONFIG_MPC5200_DDR */
-#endif /*CONFIG_LITE5200B */
-
-#define CONFIG_SYS_CS_BURST		0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE	0x33333333
-
-#define CONFIG_SYS_RESET_ADDRESS	0xff000000
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK	0x0001BBBB
-#define CONFIG_USB_CONFIG	0x00001000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef  CONFIG_IDE_8xx_PCCARD		/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-
-#define	CONFIG_IDE_RESET		/* reset for ide supported	*/
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	2	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	(0x005C)
-
-/* Interval between registers                                                */
-#define CONFIG_SYS_ATA_STRIDE          4
-
-#define CONFIG_ATAPI            1
-
-#endif /* __CONFIG_H */