Merge branch 'phylib' of git://git.denx.de/u-boot-mmc

22 files changed, 2890 insertions, 1864 deletions

diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index fd9d0b4be1..819b197673 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -79,7 +79,7 @@ COBJS-$(CONFIG_TIGON3) += tigon3.o
 COBJS-$(CONFIG_TIGON3) += bcm570x_autoneg.o
 COBJS-$(CONFIG_TIGON3) += 5701rls.o
 COBJS-$(CONFIG_DRIVER_TI_EMAC) += davinci_emac.o
-COBJS-$(CONFIG_TSEC_ENET) += tsec.o
+COBJS-$(CONFIG_TSEC_ENET) += tsec.o fsl_mdio.o
 COBJS-$(CONFIG_TSI108_ETH) += tsi108_eth.o
 COBJS-$(CONFIG_ULI526X) += uli526x.o
 COBJS-$(CONFIG_VSC7385_ENET) += vsc7385.o
diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c
index 709f67aac2..b5c55738f7 100644
--- a/drivers/net/dm9000x.c
+++ b/drivers/net/dm9000x.c
@@ -110,8 +110,8 @@ static board_info_t dm9000_info;
 
 /* function declaration ------------------------------------- */
 static int dm9000_probe(void);
-static u16 phy_read(int);
-static void phy_write(int, u16);
+static u16 dm9000_phy_read(int);
+static void dm9000_phy_write(int, u16);
 static u8 DM9000_ior(int);
 static void DM9000_iow(int reg, u8 value);
 
@@ -361,7 +361,7 @@ static int dm9000_init(struct eth_device *dev, bd_t *bd)
 	DM9000_iow(DM9000_IMR, IMR_PAR);
 
 	i = 0;
-	while (!(phy_read(1) & 0x20)) {	/* autonegation complete bit */
+	while (!(dm9000_phy_read(1) & 0x20)) {	/* autonegation complete bit */
 		udelay(1000);
 		i++;
 		if (i == 10000) {
@@ -371,7 +371,7 @@ static int dm9000_init(struct eth_device *dev, bd_t *bd)
 	}
 
 	/* see what we've got */
-	lnk = phy_read(17) >> 12;
+	lnk = dm9000_phy_read(17) >> 12;
 	printf("operating at ");
 	switch (lnk) {
 	case 1:
@@ -445,7 +445,7 @@ static void dm9000_halt(struct eth_device *netdev)
 	DM9000_DBG("%s\n", __func__);
 
 	/* RESET devie */
-	phy_write(0, 0x8000);	/* PHY RESET */
+	dm9000_phy_write(0, 0x8000);	/* PHY RESET */
 	DM9000_iow(DM9000_GPR, 0x01);	/* Power-Down PHY */
 	DM9000_iow(DM9000_IMR, 0x80);	/* Disable all interrupt */
 	DM9000_iow(DM9000_RCR, 0x00);	/* Disable RX */
@@ -581,7 +581,7 @@ DM9000_iow(int reg, u8 value)
    Read a word from phyxcer
 */
 static u16
-phy_read(int reg)
+dm9000_phy_read(int reg)
 {
 	u16 val;
 
@@ -593,7 +593,7 @@ phy_read(int reg)
 	val = (DM9000_ior(DM9000_EPDRH) << 8) | DM9000_ior(DM9000_EPDRL);
 
 	/* The read data keeps on REG_0D & REG_0E */
-	DM9000_DBG("phy_read(0x%x): 0x%x\n", reg, val);
+	DM9000_DBG("dm9000_phy_read(0x%x): 0x%x\n", reg, val);
 	return val;
 }
 
@@ -601,7 +601,7 @@ phy_read(int reg)
    Write a word to phyxcer
 */
 static void
-phy_write(int reg, u16 value)
+dm9000_phy_write(int reg, u16 value)
 {
 
 	/* Fill the phyxcer register into REG_0C */
@@ -613,7 +613,7 @@ phy_write(int reg, u16 value)
 	DM9000_iow(DM9000_EPCR, 0xa);	/* Issue phyxcer write command */
 	udelay(500);			/* Wait write complete */
 	DM9000_iow(DM9000_EPCR, 0x0);	/* Clear phyxcer write command */
-	DM9000_DBG("phy_write(reg:0x%x, value:0x%x)\n", reg, value);
+	DM9000_DBG("dm9000_phy_write(reg:0x%x, value:0x%x)\n", reg, value);
 }
 
 int dm9000_initialize(bd_t *bis)
diff --git a/drivers/net/enc28j60.c b/drivers/net/enc28j60.c
index 6c161b632f..d55cacdac8 100644
--- a/drivers/net/enc28j60.c
+++ b/drivers/net/enc28j60.c
@@ -314,7 +314,7 @@ static void enc_release_bus(enc_dev_t *enc)
 /*
  * Read PHY register
  */
-static u16 phy_read(enc_dev_t *enc, const u8 addr)
+static u16 enc_phy_read(enc_dev_t *enc, const u8 addr)
 {
 	uint64_t etime;
 	u8 status;
@@ -339,7 +339,7 @@ static u16 phy_read(enc_dev_t *enc, const u8 addr)
 /*
  * Write PHY register
  */
-static void phy_write(enc_dev_t *enc, const u8 addr, const u16 data)
+static void enc_phy_write(enc_dev_t *enc, const u8 addr, const u16 data)
 {
 	uint64_t etime;
 	u8 status;
@@ -374,7 +374,7 @@ static int enc_phy_link_wait(enc_dev_t *enc)
 
 #ifdef CONFIG_ENC_SILENTLINK
 	/* check if we have a link, then just return */
-	status = phy_read(enc, PHY_REG_PHSTAT1);
+	status = enc_phy_read(enc, PHY_REG_PHSTAT1);
 	if (status & ENC_PHSTAT1_LLSTAT)
 		return 0;
 #endif
@@ -382,10 +382,10 @@ static int enc_phy_link_wait(enc_dev_t *enc)
 	/* wait for link with 1 second timeout */
 	etime = get_ticks() + get_tbclk();
 	while (get_ticks() <= etime) {
-		status = phy_read(enc, PHY_REG_PHSTAT1);
+		status = enc_phy_read(enc, PHY_REG_PHSTAT1);
 		if (status & ENC_PHSTAT1_LLSTAT) {
 			/* now we have a link */
-			status = phy_read(enc, PHY_REG_PHSTAT2);
+			status = enc_phy_read(enc, PHY_REG_PHSTAT2);
 			duplex = (status & ENC_PHSTAT2_DPXSTAT) ? 1 : 0;
 			printf("%s: link up, 10Mbps %s-duplex\n",
 				enc->dev->name, duplex ? "full" : "half");
@@ -678,8 +678,8 @@ static int enc_setup(enc_dev_t *enc)
 	enc->bank = 0xff;	/* invalidate current bank in enc28j60 */
 
 	/* verify PHY identification */
-	phid1 = phy_read(enc, PHY_REG_PHID1);
-	phid2 = phy_read(enc, PHY_REG_PHID2) & ENC_PHID2_MASK;
+	phid1 = enc_phy_read(enc, PHY_REG_PHID1);
+	phid2 = enc_phy_read(enc, PHY_REG_PHID2) & ENC_PHID2_MASK;
 	if (phid1 != ENC_PHID1_VALUE || phid2 != ENC_PHID2_VALUE) {
 		printf("%s: failed to identify PHY. Found %04x:%04x\n",
 			enc->dev->name, phid1, phid2);
@@ -694,7 +694,7 @@ static int enc_setup(enc_dev_t *enc)
 	 * Prevent automatic loopback of data beeing transmitted by setting
 	 * ENC_PHCON2_HDLDIS
 	 */
-	phy_write(enc, PHY_REG_PHCON2, (1<<8));
+	enc_phy_write(enc, PHY_REG_PHCON2, (1<<8));
 
 	/*
 	 * LEDs configuration
@@ -702,10 +702,10 @@ static int enc_setup(enc_dev_t *enc)
 	 * LEDB: LBCFG = 0111 -> display TX & RX activity
 	 * STRCH = 1 -> LED pulses
 	 */
-	phy_write(enc, PHY_REG_PHLCON, 0x0472);
+	enc_phy_write(enc, PHY_REG_PHLCON, 0x0472);
 
 	/* Reset PDPXMD-bit => half duplex */
-	phy_write(enc, PHY_REG_PHCON1, 0);
+	enc_phy_write(enc, PHY_REG_PHCON1, 0);
 
 #ifdef CONFIG_USE_IRQ
 	/* enable interrupts */
@@ -771,7 +771,7 @@ int enc_miiphy_read(const char *devname, u8 phy_adr, u8 reg, u16 *value)
 		enc_release_bus(enc);
 		return -1;
 	}
-	*value = phy_read(enc, reg);
+	*value = enc_phy_read(enc, reg);
 	enc_release_bus(enc);
 	return 0;
 }
@@ -796,7 +796,7 @@ int enc_miiphy_write(const char *devname, u8 phy_adr, u8 reg, u16 value)
 		enc_release_bus(enc);
 		return -1;
 	}
-	phy_write(enc, reg, value);
+	enc_phy_write(enc, reg, value);
 	enc_release_bus(enc);
 	return 0;
 }
diff --git a/drivers/net/fsl_mdio.c b/drivers/net/fsl_mdio.c
new file mode 100644
index 0000000000..1aab307897
--- /dev/null
+++ b/drivers/net/fsl_mdio.c
@@ -0,0 +1,120 @@
+/*
+ * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ *	Jun-jie Zhang <b18070@freescale.com>
+ *	Mingkai Hu <Mingkai.hu@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <fsl_mdio.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/fsl_enet.h>
+
+void tsec_local_mdio_write(struct tsec_mii_mng *phyregs, int port_addr,
+		int dev_addr, int regnum, int value)
+{
+	int timeout = 1000000;
+
+	out_be32(&phyregs->miimadd, (port_addr << 8) | (regnum & 0x1f));
+	out_be32(&phyregs->miimcon, value);
+	asm("sync");
+
+	while ((in_be32(&phyregs->miimind) & MIIMIND_BUSY) && timeout--)
+		;
+}
+
+int tsec_local_mdio_read(struct tsec_mii_mng *phyregs, int port_addr,
+		int dev_addr, int regnum)
+{
+	int value;
+	int timeout = 1000000;
+
+	/* Put the address of the phy, and the register
+	 * number into MIIMADD */
+	out_be32(&phyregs->miimadd, (port_addr << 8) | (regnum & 0x1f));
+
+	/* Clear the command register, and wait */
+	out_be32(&phyregs->miimcom, 0);
+	asm("sync");
+
+	/* Initiate a read command, and wait */
+	out_be32(&phyregs->miimcom, MIIMCOM_READ_CYCLE);
+	asm("sync");
+
+	/* Wait for the the indication that the read is done */
+	while ((in_be32(&phyregs->miimind) & (MIIMIND_NOTVALID | MIIMIND_BUSY))
+			&& timeout--)
+		;
+
+	/* Grab the value read from the PHY */
+	value = in_be32(&phyregs->miimstat);
+
+	return value;
+}
+
+static int fsl_pq_mdio_reset(struct mii_dev *bus)
+{
+	struct tsec_mii_mng *regs = bus->priv;
+
+	/* Reset MII (due to new addresses) */
+	out_be32(&regs->miimcfg, MIIMCFG_RESET_MGMT);
+
+	out_be32(&regs->miimcfg, MIIMCFG_INIT_VALUE);
+
+	while (in_be32(&regs->miimind) & MIIMIND_BUSY)
+		;
+
+	return 0;
+}
+
+int tsec_phy_read(struct mii_dev *bus, int addr, int dev_addr, int regnum)
+{
+	struct tsec_mii_mng *phyregs = bus->priv;
+
+	return tsec_local_mdio_read(phyregs, addr, dev_addr, regnum);
+}
+
+int tsec_phy_write(struct mii_dev *bus, int addr, int dev_addr, int regnum,
+			u16 value)
+{
+	struct tsec_mii_mng *phyregs = bus->priv;
+
+	tsec_local_mdio_write(phyregs, addr, dev_addr, regnum, value);
+
+	return 0;
+}
+
+int fsl_pq_mdio_init(bd_t *bis, struct fsl_pq_mdio_info *info)
+{
+	struct mii_dev *bus = mdio_alloc();
+
+	if (!bus) {
+		printf("Failed to allocate FSL MDIO bus\n");
+		return -1;
+	}
+
+	bus->read = tsec_phy_read;
+	bus->write = tsec_phy_write;
+	bus->reset = fsl_pq_mdio_reset;
+	sprintf(bus->name, info->name);
+
+	bus->priv = info->regs;
+
+	return mdio_register(bus);
+}
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index bba890189a..a59834b292 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -28,6 +28,19 @@ LIB	:= $(obj)libphy.o
 COBJS-$(CONFIG_BITBANGMII) += miiphybb.o
 COBJS-$(CONFIG_MV88E61XX_SWITCH) += mv88e61xx.o
 
+COBJS-$(CONFIG_PHYLIB) += phy.o
+COBJS-$(CONFIG_PHYLIB_10G) += generic_10g.o
+COBJS-$(CONFIG_PHY_ATHEROS) += atheros.o
+COBJS-$(CONFIG_PHY_BROADCOM) += broadcom.o
+COBJS-$(CONFIG_PHY_DAVICOM) += davicom.o
+COBJS-$(CONFIG_PHY_LXT) += lxt.o
+COBJS-$(CONFIG_PHY_MARVELL) += marvell.o
+COBJS-$(CONFIG_PHY_MICREL) += micrel.o
+COBJS-$(CONFIG_PHY_NATSEMI) += natsemi.o
+COBJS-$(CONFIG_PHY_REALTEK) += realtek.o
+COBJS-$(CONFIG_PHY_TERANETICS) += teranetics.o
+COBJS-$(CONFIG_PHY_VITESSE) += vitesse.o
+
 COBJS	:= $(COBJS-y)
 SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/drivers/net/phy/atheros.c b/drivers/net/phy/atheros.c
new file mode 100644
index 0000000000..798473dd68
--- /dev/null
+++ b/drivers/net/phy/atheros.c
@@ -0,0 +1,48 @@
+/*
+ * Atheros PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <phy.h>
+
+static int ar8021_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3D47);
+
+	return 0;
+}
+
+struct phy_driver AR8021_driver =  {
+	.name = "AR8021",
+	.uid = 0x4dd040,
+	.mask = 0xfffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = ar8021_config,
+	.startup = genphy_startup,
+	.shutdown = genphy_shutdown,
+};
+
+int phy_atheros_init(void)
+{
+	phy_register(&AR8021_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
new file mode 100644
index 0000000000..427ac6013b
--- /dev/null
+++ b/drivers/net/phy/broadcom.c
@@ -0,0 +1,288 @@
+/*
+ * Broadcom PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <config.h>
+#include <common.h>
+#include <phy.h>
+
+/* Broadcom BCM54xx -- taken from linux sungem_phy */
+#define MIIM_BCM54xx_AUXCNTL			0x18
+#define MIIM_BCM54xx_AUXCNTL_ENCODE(val) (((val & 0x7) << 12)|(val & 0x7))
+#define MIIM_BCM54xx_AUXSTATUS			0x19
+#define MIIM_BCM54xx_AUXSTATUS_LINKMODE_MASK	0x0700
+#define MIIM_BCM54xx_AUXSTATUS_LINKMODE_SHIFT	8
+
+#define MIIM_BCM54XX_SHD			0x1c
+#define MIIM_BCM54XX_SHD_WRITE			0x8000
+#define MIIM_BCM54XX_SHD_VAL(x)			((x & 0x1f) << 10)
+#define MIIM_BCM54XX_SHD_DATA(x)		((x & 0x3ff) << 0)
+#define MIIM_BCM54XX_SHD_WR_ENCODE(val, data)	\
+	(MIIM_BCM54XX_SHD_WRITE | MIIM_BCM54XX_SHD_VAL(val) | \
+	 MIIM_BCM54XX_SHD_DATA(data))
+
+#define MIIM_BCM54XX_EXP_DATA		0x15	/* Expansion register data */
+#define MIIM_BCM54XX_EXP_SEL		0x17	/* Expansion register select */
+#define MIIM_BCM54XX_EXP_SEL_SSD	0x0e00	/* Secondary SerDes select */
+#define MIIM_BCM54XX_EXP_SEL_ER		0x0f00	/* Expansion register select */
+
+/* Broadcom BCM5461S */
+static int bcm5461_config(struct phy_device *phydev)
+{
+	genphy_config_aneg(phydev);
+
+	phy_reset(phydev);
+
+	return 0;
+}
+
+static int bcm54xx_parse_status(struct phy_device *phydev)
+{
+	unsigned int mii_reg;
+
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_BCM54xx_AUXSTATUS);
+
+	switch ((mii_reg & MIIM_BCM54xx_AUXSTATUS_LINKMODE_MASK) >>
+			MIIM_BCM54xx_AUXSTATUS_LINKMODE_SHIFT) {
+	case 1:
+		phydev->duplex = DUPLEX_HALF;
+		phydev->speed = SPEED_10;
+		break;
+	case 2:
+		phydev->duplex = DUPLEX_FULL;
+		phydev->speed = SPEED_10;
+		break;
+	case 3:
+		phydev->duplex = DUPLEX_HALF;
+		phydev->speed = SPEED_100;
+		break;
+	case 5:
+		phydev->duplex = DUPLEX_FULL;
+		phydev->speed = SPEED_100;
+		break;
+	case 6:
+		phydev->duplex = DUPLEX_HALF;
+		phydev->speed = SPEED_1000;
+		break;
+	case 7:
+		phydev->duplex = DUPLEX_FULL;
+		phydev->speed = SPEED_1000;
+		break;
+	default:
+		printf("Auto-neg error, defaulting to 10BT/HD\n");
+		phydev->duplex = DUPLEX_HALF;
+		phydev->speed = SPEED_10;
+		break;
+	}
+
+	return 0;
+}
+
+static int bcm54xx_startup(struct phy_device *phydev)
+{
+	/* Read the Status (2x to make sure link is right) */
+	genphy_update_link(phydev);
+	bcm54xx_parse_status(phydev);
+
+	return 0;
+}
+
+/* Broadcom BCM5482S */
+/*
+ * "Ethernet@Wirespeed" needs to be enabled to achieve link in certain
+ * circumstances.  eg a gigabit TSEC connected to a gigabit switch with
+ * a 4-wire ethernet cable.  Both ends advertise gigabit, but can't
+ * link.  "Ethernet@Wirespeed" reduces advertised speed until link
+ * can be achieved.
+ */
+static u32 bcm5482_read_wirespeed(struct phy_device *phydev, u32 reg)
+{
+	return (phy_read(phydev, MDIO_DEVAD_NONE, reg) & 0x8FFF) | 0x8010;
+}
+
+static int bcm5482_config(struct phy_device *phydev)
+{
+	unsigned int reg;
+
+	/* reset the PHY */
+	reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+	reg |= BMCR_RESET;
+	phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, reg);
+
+	/* Setup read from auxilary control shadow register 7 */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_BCM54xx_AUXCNTL,
+			MIIM_BCM54xx_AUXCNTL_ENCODE(7));
+	/* Read Misc Control register and or in Ethernet@Wirespeed */
+	reg = bcm5482_read_wirespeed(phydev, MIIM_BCM54xx_AUXCNTL);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_BCM54xx_AUXCNTL, reg);
+
+	/* Initial config/enable of secondary SerDes interface */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_BCM54XX_SHD,
+			MIIM_BCM54XX_SHD_WR_ENCODE(0x14, 0xf));
+	/* Write intial value to secondary SerDes Contol */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_BCM54XX_EXP_SEL,
+			MIIM_BCM54XX_EXP_SEL_SSD | 0);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_BCM54XX_EXP_DATA,
+			BMCR_ANRESTART);
+	/* Enable copper/fiber auto-detect */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_BCM54XX_SHD,
+			MIIM_BCM54XX_SHD_WR_ENCODE(0x1e, 0x201));
+
+	genphy_config_aneg(phydev);
+
+	return 0;
+}
+
+/*
+ * Find out if PHY is in copper or serdes mode by looking at Expansion Reg
+ * 0x42 - "Operating Mode Status Register"
+ */
+static int bcm5482_is_serdes(struct phy_device *phydev)
+{
+	u16 val;
+	int serdes = 0;
+
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_BCM54XX_EXP_SEL,
+			MIIM_BCM54XX_EXP_SEL_ER | 0x42);
+	val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_BCM54XX_EXP_DATA);
+
+	switch (val & 0x1f) {
+	case 0x0d:	/* RGMII-to-100Base-FX */
+	case 0x0e:	/* RGMII-to-SGMII */
+	case 0x0f:	/* RGMII-to-SerDes */
+	case 0x12:	/* SGMII-to-SerDes */
+	case 0x13:	/* SGMII-to-100Base-FX */
+	case 0x16:	/* SerDes-to-Serdes */
+		serdes = 1;
+		break;
+	case 0x6:	/* RGMII-to-Copper */
+	case 0x14:	/* SGMII-to-Copper */
+	case 0x17:	/* SerDes-to-Copper */
+		break;
+	default:
+		printf("ERROR, invalid PHY mode (0x%x\n)", val);
+		break;
+	}
+
+	return serdes;
+}
+
+/*
+ * Determine SerDes link speed and duplex from Expansion reg 0x42 "Operating
+ * Mode Status Register"
+ */
+static u32 bcm5482_parse_serdes_sr(struct phy_device *phydev)
+{
+	u16 val;
+	int i = 0;
+
+	/* Wait 1s for link - Clause 37 autonegotiation happens very fast */
+	while (1) {
+		phy_write(phydev, MDIO_DEVAD_NONE, MIIM_BCM54XX_EXP_SEL,
+				MIIM_BCM54XX_EXP_SEL_ER | 0x42);
+		val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_BCM54XX_EXP_DATA);
+
+		if (val & 0x8000)
+			break;
+
+		if (i++ > 1000) {
+			phydev->link = 0;
+			return 1;
+		}
+
+		udelay(1000);	/* 1 ms */
+	}
+
+	phydev->link = 1;
+	switch ((val >> 13) & 0x3) {
+	case (0x00):
+		phydev->speed = 10;
+		break;
+	case (0x01):
+		phydev->speed = 100;
+		break;
+	case (0x02):
+		phydev->speed = 1000;
+		break;
+	}
+
+	phydev->duplex = (val & 0x1000) == 0x1000;
+
+	return 0;
+}
+
+/*
+ * Figure out if BCM5482 is in serdes or copper mode and determine link
+ * configuration accordingly
+ */
+static int bcm5482_startup(struct phy_device *phydev)
+{
+	if (bcm5482_is_serdes(phydev)) {
+		bcm5482_parse_serdes_sr(phydev);
+		phydev->port = PORT_FIBRE;
+	} else {
+		/* Wait for auto-negotiation to complete or fail */
+		genphy_update_link(phydev);
+		/* Parse BCM54xx copper aux status register */
+		bcm54xx_parse_status(phydev);
+	}
+
+	return 0;
+}
+
+static struct phy_driver BCM5461S_driver = {
+	.name = "Broadcom BCM5461S",
+	.uid = 0x2060c0,
+	.mask = 0xfffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &bcm5461_config,
+	.startup = &bcm54xx_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver BCM5464S_driver = {
+	.name = "Broadcom BCM5464S",
+	.uid = 0x2060b0,
+	.mask = 0xfffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &bcm5461_config,
+	.startup = &bcm54xx_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver BCM5482S_driver = {
+	.name = "Broadcom BCM5482S",
+	.uid = 0x143bcb0,
+	.mask = 0xffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &bcm5482_config,
+	.startup = &bcm5482_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+int phy_broadcom_init(void)
+{
+	phy_register(&BCM5482S_driver);
+	phy_register(&BCM5464S_driver);
+	phy_register(&BCM5461S_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/davicom.c b/drivers/net/phy/davicom.c
new file mode 100644
index 0000000000..e96a4af03d
--- /dev/null
+++ b/drivers/net/phy/davicom.c
@@ -0,0 +1,98 @@
+/*
+ * Davicom PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <phy.h>
+
+#define MIIM_DM9161_SCR                0x10
+#define MIIM_DM9161_SCR_INIT   0x0610
+
+/* DM9161 Specified Configuration and Status Register */
+#define MIIM_DM9161_SCSR       0x11
+#define MIIM_DM9161_SCSR_100F  0x8000
+#define MIIM_DM9161_SCSR_100H  0x4000
+#define MIIM_DM9161_SCSR_10F   0x2000
+#define MIIM_DM9161_SCSR_10H   0x1000
+
+/* DM9161 10BT Configuration/Status */
+#define MIIM_DM9161_10BTCSR    0x12
+#define MIIM_DM9161_10BTCSR_INIT       0x7800
+
+
+/* Davicom DM9161E */
+static int dm9161_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, BMCR_ISOLATE);
+	/* Do not bypass the scrambler/descrambler */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_DM9161_SCR,
+			MIIM_DM9161_SCR_INIT);
+	/* Clear 10BTCSR to default */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_DM9161_10BTCSR,
+			MIIM_DM9161_10BTCSR_INIT);
+
+	genphy_config_aneg(phydev);
+
+	return 0;
+}
+
+static int dm9161_parse_status(struct phy_device *phydev)
+{
+	int mii_reg;
+
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_DM9161_SCSR);
+
+	if (mii_reg & (MIIM_DM9161_SCSR_100F | MIIM_DM9161_SCSR_100H))
+		phydev->speed = SPEED_100;
+	else
+		phydev->speed = SPEED_10;
+
+	if (mii_reg & (MIIM_DM9161_SCSR_100F | MIIM_DM9161_SCSR_10F))
+		phydev->duplex = DUPLEX_FULL;
+	else
+		phydev->duplex = DUPLEX_HALF;
+
+	return 0;
+}
+
+static int dm9161_startup(struct phy_device *phydev)
+{
+	genphy_update_link(phydev);
+	dm9161_parse_status(phydev);
+
+	return 0;
+}
+
+static struct phy_driver DM9161_driver = {
+	.name = "Davicom DM9161E",
+	.uid = 0x181b880,
+	.mask = 0xffffff0,
+	.features = PHY_BASIC_FEATURES,
+	.config = &dm9161_config,
+	.startup = &dm9161_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+int phy_davicom_init(void)
+{
+	phy_register(&DM9161_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/generic_10g.c b/drivers/net/phy/generic_10g.c
new file mode 100644
index 0000000000..315c50867d
--- /dev/null
+++ b/drivers/net/phy/generic_10g.c
@@ -0,0 +1,105 @@
+/*
+ * Generic PHY Management code
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ *
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ * Based loosely off of Linux's PHY Lib
+ */
+
+#include <config.h>
+#include <common.h>
+#include <miiphy.h>
+#include <phy.h>
+
+int gen10g_shutdown(struct phy_device *phydev)
+{
+	return 0;
+}
+
+int gen10g_startup(struct phy_device *phydev)
+{
+	int devad, reg;
+	u32 mmd_mask = phydev->mmds;
+
+	phydev->link = 1;
+
+	/* For now just lie and say it's 10G all the time */
+	phydev->speed = SPEED_10000;
+	phydev->duplex = DUPLEX_FULL;
+
+	for (devad = 0; mmd_mask; devad++, mmd_mask = mmd_mask >> 1) {
+		if (!mmd_mask & 1)
+			continue;
+
+		/* Read twice because link state is latched and a
+		 * read moves the current state into the register */
+		phy_read(phydev, devad, MDIO_STAT1);
+		reg = phy_read(phydev, devad, MDIO_STAT1);
+		if (reg < 0 || !(reg & MDIO_STAT1_LSTATUS))
+			phydev->link = 0;
+	}
+
+	return 0;
+}
+
+int gen10g_discover_mmds(struct phy_device *phydev)
+{
+	int mmd, stat2, devs1, devs2;
+
+	/* Assume PHY must have at least one of PMA/PMD, WIS, PCS, PHY
+	 * XS or DTE XS; give up if none is present. */
+	for (mmd = 1; mmd <= 5; mmd++) {
+		/* Is this MMD present? */
+		stat2 = phy_read(phydev, mmd, MDIO_STAT2);
+		if (stat2 < 0 ||
+			(stat2 & MDIO_STAT2_DEVPRST) != MDIO_STAT2_DEVPRST_VAL)
+			continue;
+
+		/* It should tell us about all the other MMDs */
+		devs1 = phy_read(phydev, mmd, MDIO_DEVS1);
+		devs2 = phy_read(phydev, mmd, MDIO_DEVS2);
+		if (devs1 < 0 || devs2 < 0)
+			continue;
+
+		phydev->mmds = devs1 | (devs2 << 16);
+		return 0;
+	}
+
+	return 0;
+}
+
+int gen10g_config(struct phy_device *phydev)
+{
+	/* For now, assume 10000baseT. Fill in later */
+	phydev->supported = phydev->advertising = SUPPORTED_10000baseT_Full;
+
+	return gen10g_discover_mmds(phydev);
+}
+
+struct phy_driver gen10g_driver = {
+	.uid		= 0xffffffff,
+	.mask		= 0xffffffff,
+	.name		= "Generic 10G PHY",
+	.features	= 0,
+	.config		= gen10g_config,
+	.startup	= gen10g_startup,
+	.shutdown	= gen10g_shutdown,
+};
+
diff --git a/drivers/net/phy/lxt.c b/drivers/net/phy/lxt.c
new file mode 100644
index 0000000000..d67bbdd9ca
--- /dev/null
+++ b/drivers/net/phy/lxt.c
@@ -0,0 +1,87 @@
+/*
+ * LXT PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <phy.h>
+
+/* LXT971 Status 2 registers */
+#define MIIM_LXT971_SR2                     0x11  /* Status Register 2  */
+#define MIIM_LXT971_SR2_SPEED_MASK 0x4200
+#define MIIM_LXT971_SR2_10HDX     0x0000  /*  10 Mbit half duplex selected */
+#define MIIM_LXT971_SR2_10FDX     0x0200  /*  10 Mbit full duplex selected */
+#define MIIM_LXT971_SR2_100HDX    0x4000  /* 100 Mbit half duplex selected */
+#define MIIM_LXT971_SR2_100FDX    0x4200  /* 100 Mbit full duplex selected */
+
+
+/* LXT971 */
+static int lxt971_parse_status(struct phy_device *phydev)
+{
+	int mii_reg;
+	int speed;
+
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_LXT971_SR2);
+	speed = mii_reg & MIIM_LXT971_SR2_SPEED_MASK;
+
+	switch (speed) {
+	case MIIM_LXT971_SR2_10HDX:
+		phydev->speed = SPEED_10;
+		phydev->duplex = DUPLEX_HALF;
+		break;
+	case MIIM_LXT971_SR2_10FDX:
+		phydev->speed = SPEED_10;
+		phydev->duplex = DUPLEX_FULL;
+		break;
+	case MIIM_LXT971_SR2_100HDX:
+		phydev->speed = SPEED_100;
+		phydev->duplex = DUPLEX_HALF;
+		break;
+	default:
+		phydev->speed = SPEED_100;
+		phydev->duplex = DUPLEX_FULL;
+	}
+
+	return 0;
+}
+
+static int lxt971_startup(struct phy_device *phydev)
+{
+	genphy_update_link(phydev);
+	lxt971_parse_status(phydev);
+
+	return 0;
+}
+
+static struct phy_driver LXT971_driver = {
+	.name = "LXT971",
+	.uid = 0x1378e0,
+	.mask = 0xfffff0,
+	.features = PHY_BASIC_FEATURES,
+	.config = &genphy_config_aneg,
+	.startup = &lxt971_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+int phy_lxt_init(void)
+{
+	phy_register(&LXT971_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
new file mode 100644
index 0000000000..bd1cdc4f11
--- /dev/null
+++ b/drivers/net/phy/marvell.c
@@ -0,0 +1,367 @@
+/*
+ * Marvell PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <config.h>
+#include <common.h>
+#include <phy.h>
+
+#define PHY_AUTONEGOTIATE_TIMEOUT 5000
+
+/* 88E1011 PHY Status Register */
+#define MIIM_88E1xxx_PHY_STATUS		0x11
+#define MIIM_88E1xxx_PHYSTAT_SPEED	0xc000
+#define MIIM_88E1xxx_PHYSTAT_GBIT	0x8000
+#define MIIM_88E1xxx_PHYSTAT_100	0x4000
+#define MIIM_88E1xxx_PHYSTAT_DUPLEX	0x2000
+#define MIIM_88E1xxx_PHYSTAT_SPDDONE	0x0800
+#define MIIM_88E1xxx_PHYSTAT_LINK	0x0400
+
+#define MIIM_88E1xxx_PHY_SCR		0x10
+#define MIIM_88E1xxx_PHY_MDI_X_AUTO	0x0060
+
+/* 88E1111 PHY LED Control Register */
+#define MIIM_88E1111_PHY_LED_CONTROL	24
+#define MIIM_88E1111_PHY_LED_DIRECT	0x4100
+#define MIIM_88E1111_PHY_LED_COMBINE	0x411C
+
+/* 88E1118 PHY defines */
+#define MIIM_88E1118_PHY_PAGE		22
+#define MIIM_88E1118_PHY_LED_PAGE	3
+
+/* 88E1121 PHY LED Control Register */
+#define MIIM_88E1121_PHY_LED_CTRL	16
+#define MIIM_88E1121_PHY_LED_PAGE	3
+#define MIIM_88E1121_PHY_LED_DEF	0x0030
+
+/* 88E1121 PHY IRQ Enable/Status Register */
+#define MIIM_88E1121_PHY_IRQ_EN		18
+#define MIIM_88E1121_PHY_IRQ_STATUS	19
+
+#define MIIM_88E1121_PHY_PAGE		22
+
+/* 88E1145 Extended PHY Specific Control Register */
+#define MIIM_88E1145_PHY_EXT_CR 20
+#define MIIM_M88E1145_RGMII_RX_DELAY	0x0080
+#define MIIM_M88E1145_RGMII_TX_DELAY	0x0002
+
+#define MIIM_88E1145_PHY_LED_CONTROL	24
+#define MIIM_88E1145_PHY_LED_DIRECT	0x4100
+
+#define MIIM_88E1145_PHY_PAGE	29
+#define MIIM_88E1145_PHY_CAL_OV 30
+
+#define MIIM_88E1149_PHY_PAGE	29
+
+/* Marvell 88E1011S */
+static int m88e1011s_config(struct phy_device *phydev)
+{
+	/* Reset and configure the PHY */
+	phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, BMCR_RESET);
+
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x200c);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, BMCR_RESET);
+
+	genphy_config_aneg(phydev);
+
+	return 0;
+}
+
+/* Parse the 88E1011's status register for speed and duplex
+ * information
+ */
+static uint m88e1xxx_parse_status(struct phy_device *phydev)
+{
+	unsigned int speed;
+	unsigned int mii_reg;
+
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1xxx_PHY_STATUS);
+
+	if ((mii_reg & MIIM_88E1xxx_PHYSTAT_LINK) &&
+		!(mii_reg & MIIM_88E1xxx_PHYSTAT_SPDDONE)) {
+		int i = 0;
+
+		puts("Waiting for PHY realtime link");
+		while (!(mii_reg & MIIM_88E1xxx_PHYSTAT_SPDDONE)) {
+			/* Timeout reached ? */
+			if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
+				puts(" TIMEOUT !\n");
+				phydev->link = 0;
+				break;
+			}
+
+			if ((i++ % 1000) == 0)
+				putc('.');
+			udelay(1000);
+			mii_reg = phy_read(phydev, MDIO_DEVAD_NONE,
+					MIIM_88E1xxx_PHY_STATUS);
+		}
+		puts(" done\n");
+		udelay(500000);	/* another 500 ms (results in faster booting) */
+	} else {
+		if (mii_reg & MIIM_88E1xxx_PHYSTAT_LINK)
+			phydev->link = 1;
+		else
+			phydev->link = 0;
+	}
+
+	if (mii_reg & MIIM_88E1xxx_PHYSTAT_DUPLEX)
+		phydev->duplex = DUPLEX_FULL;
+	else
+		phydev->duplex = DUPLEX_HALF;
+
+	speed = mii_reg & MIIM_88E1xxx_PHYSTAT_SPEED;
+
+	switch (speed) {
+	case MIIM_88E1xxx_PHYSTAT_GBIT:
+		phydev->speed = SPEED_1000;
+		break;
+	case MIIM_88E1xxx_PHYSTAT_100:
+		phydev->speed = SPEED_100;
+		break;
+	default:
+		phydev->speed = SPEED_10;
+		break;
+	}
+
+	return 0;
+}
+
+static int m88e1011s_startup(struct phy_device *phydev)
+{
+	genphy_update_link(phydev);
+	m88e1xxx_parse_status(phydev);
+
+	return 0;
+}
+
+/* Marvell 88E1111S */
+static int m88e1111s_config(struct phy_device *phydev)
+{
+	int reg;
+
+	if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) ||
+			(phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) ||
+			(phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) ||
+			(phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) {
+		reg = phy_read(phydev, MDIO_DEVAD_NONE, 0x1b);
+		reg = (reg & 0xfff0) | 0xb;
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1b, reg);
+	} else {
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1b, 0x1f);
+	}
+
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x14, 0x0cd2);
+
+	genphy_config_aneg(phydev);
+
+	phy_reset(phydev);
+
+	return 0;
+}
+
+/* Marvell 88E1118 */
+static int m88e1118_config(struct phy_device *phydev)
+{
+	/* Change Page Number */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0002);
+	/* Delay RGMII TX and RX */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x15, 0x1070);
+	/* Change Page Number */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0003);
+	/* Adjust LED control */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x021e);
+	/* Change Page Number */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000);
+
+	genphy_config_aneg(phydev);
+
+	phy_reset(phydev);
+
+	return 0;
+}
+
+static int m88e1118_startup(struct phy_device *phydev)
+{
+	/* Change Page Number */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000);
+
+	genphy_update_link(phydev);
+	m88e1xxx_parse_status(phydev);
+
+	return 0;
+}
+
+/* Marvell 88E1121R */
+static int m88e1121_config(struct phy_device *phydev)
+{
+	int pg;
+
+	/* Configure the PHY */
+	genphy_config_aneg(phydev);
+
+	/* Switch the page to access the led register */
+	pg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_PAGE);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_PAGE,
+			MIIM_88E1121_PHY_LED_PAGE);
+	/* Configure leds */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_LED_CTRL,
+			MIIM_88E1121_PHY_LED_DEF);
+	/* Restore the page pointer */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_PAGE, pg);
+
+	/* Disable IRQs and de-assert interrupt */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_IRQ_EN, 0);
+	phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_IRQ_STATUS);
+
+	return 0;
+}
+
+/* Marvell 88E1145 */
+static int m88e1145_config(struct phy_device *phydev)
+{
+	int reg;
+
+	/* Errata E0, E1 */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_PAGE, 0x001b);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_CAL_OV, 0x418f);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_PAGE, 0x0016);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_CAL_OV, 0xa2da);
+
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1xxx_PHY_SCR,
+			MIIM_88E1xxx_PHY_MDI_X_AUTO);
+
+	reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_EXT_CR);
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)
+		reg |= MIIM_M88E1145_RGMII_RX_DELAY |
+			MIIM_M88E1145_RGMII_TX_DELAY;
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_EXT_CR, reg);
+
+	genphy_config_aneg(phydev);
+
+	phy_reset(phydev);
+
+	return 0;
+}
+
+static int m88e1145_startup(struct phy_device *phydev)
+{
+	genphy_update_link(phydev);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_LED_CONTROL,
+			MIIM_88E1145_PHY_LED_DIRECT);
+	m88e1xxx_parse_status(phydev);
+
+	return 0;
+}
+
+/* Marvell 88E1149S */
+static int m88e1149_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1149_PHY_PAGE, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x200c);
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1149_PHY_PAGE, 0x5);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x0);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	genphy_config_aneg(phydev);
+
+	phy_reset(phydev);
+
+	return 0;
+}
+
+
+static struct phy_driver M88E1011S_driver = {
+	.name = "Marvell 88E1011S",
+	.uid = 0x1410c60,
+	.mask = 0xffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &m88e1011s_config,
+	.startup = &m88e1011s_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver M88E1111S_driver = {
+	.name = "Marvell 88E1111S",
+	.uid = 0x1410cc0,
+	.mask = 0xffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &m88e1111s_config,
+	.startup = &m88e1011s_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver M88E1118_driver = {
+	.name = "Marvell 88E1118",
+	.uid = 0x1410e10,
+	.mask = 0xffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &m88e1118_config,
+	.startup = &m88e1118_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver M88E1121R_driver = {
+	.name = "Marvell 88E1121R",
+	.uid = 0x1410cb0,
+	.mask = 0xffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &m88e1121_config,
+	.startup = &genphy_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver M88E1145_driver = {
+	.name = "Marvell 88E1145",
+	.uid = 0x1410cd0,
+	.mask = 0xffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &m88e1145_config,
+	.startup = &m88e1145_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver M88E1149S_driver = {
+	.name = "Marvell 88E1149S",
+	.uid = 0x1410ca0,
+	.mask = 0xffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &m88e1149_config,
+	.startup = &m88e1011s_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+int phy_marvell_init(void)
+{
+	phy_register(&M88E1149S_driver);
+	phy_register(&M88E1145_driver);
+	phy_register(&M88E1121R_driver);
+	phy_register(&M88E1118_driver);
+	phy_register(&M88E1111S_driver);
+	phy_register(&M88E1011S_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
new file mode 100644
index 0000000000..47064a1853
--- /dev/null
+++ b/drivers/net/phy/micrel.c
@@ -0,0 +1,40 @@
+/*
+ * Micrel PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <phy.h>
+
+static struct phy_driver KSZ804_driver = {
+	.name = "Micrel KSZ804",
+	.uid = 0x221510,
+	.mask = 0xfffff0,
+	.features = PHY_BASIC_FEATURES,
+	.config = &genphy_config,
+	.startup = &genphy_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+int phy_micrel_init(void)
+{
+	phy_register(&KSZ804_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/natsemi.c b/drivers/net/phy/natsemi.c
new file mode 100644
index 0000000000..ea60ac1b0e
--- /dev/null
+++ b/drivers/net/phy/natsemi.c
@@ -0,0 +1,96 @@
+/*
+ * National Semiconductor PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <phy.h>
+
+/* DP83865 Link and Auto-Neg Status Register */
+#define MIIM_DP83865_LANR      0x11
+#define MIIM_DP83865_SPD_MASK  0x0018
+#define MIIM_DP83865_SPD_1000  0x0010
+#define MIIM_DP83865_SPD_100   0x0008
+#define MIIM_DP83865_DPX_FULL  0x0002
+
+
+/* NatSemi DP83865 */
+static int dp83865_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, BMCR_RESET);
+	genphy_config_aneg(phydev);
+
+	return 0;
+}
+
+static int dp83865_parse_status(struct phy_device *phydev)
+{
+	int mii_reg;
+
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_DP83865_LANR);
+
+	switch (mii_reg & MIIM_DP83865_SPD_MASK) {
+
+	case MIIM_DP83865_SPD_1000:
+		phydev->speed = SPEED_1000;
+		break;
+
+	case MIIM_DP83865_SPD_100:
+		phydev->speed = SPEED_100;
+		break;
+
+	default:
+		phydev->speed = SPEED_10;
+		break;
+
+	}
+
+	if (mii_reg & MIIM_DP83865_DPX_FULL)
+		phydev->duplex = DUPLEX_FULL;
+	else
+		phydev->duplex = DUPLEX_HALF;
+
+	return 0;
+}
+
+static int dp83865_startup(struct phy_device *phydev)
+{
+	genphy_update_link(phydev);
+	dp83865_parse_status(phydev);
+
+	return 0;
+}
+
+
+static struct phy_driver DP83865_driver = {
+	.name = "NatSemi DP83865",
+	.uid = 0x20005c70,
+	.mask = 0xfffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &dp83865_config,
+	.startup = &dp83865_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+int phy_natsemi_init(void)
+{
+	phy_register(&DP83865_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
new file mode 100644
index 0000000000..c7edcc0909
--- /dev/null
+++ b/drivers/net/phy/phy.c
@@ -0,0 +1,755 @@
+/*
+ * Generic PHY Management code
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ *
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ * Based loosely off of Linux's PHY Lib
+ */
+
+#include <config.h>
+#include <common.h>
+#include <malloc.h>
+#include <net.h>
+#include <command.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <errno.h>
+
+/* Generic PHY support and helper functions */
+
+/**
+ * genphy_config_advert - sanitize and advertise auto-negotation parameters
+ * @phydev: target phy_device struct
+ *
+ * Description: Writes MII_ADVERTISE with the appropriate values,
+ *   after sanitizing the values to make sure we only advertise
+ *   what is supported.  Returns < 0 on error, 0 if the PHY's advertisement
+ *   hasn't changed, and > 0 if it has changed.
+ */
+int genphy_config_advert(struct phy_device *phydev)
+{
+	u32 advertise;
+	int oldadv, adv;
+	int err, changed = 0;
+
+	/* Only allow advertising what
+	 * this PHY supports */
+	phydev->advertising &= phydev->supported;
+	advertise = phydev->advertising;
+
+	/* Setup standard advertisement */
+	oldadv = adv = phy_read(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE);
+
+	if (adv < 0)
+		return adv;
+
+	adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4 | ADVERTISE_PAUSE_CAP |
+		 ADVERTISE_PAUSE_ASYM);
+	if (advertise & ADVERTISED_10baseT_Half)
+		adv |= ADVERTISE_10HALF;
+	if (advertise & ADVERTISED_10baseT_Full)
+		adv |= ADVERTISE_10FULL;
+	if (advertise & ADVERTISED_100baseT_Half)
+		adv |= ADVERTISE_100HALF;
+	if (advertise & ADVERTISED_100baseT_Full)
+		adv |= ADVERTISE_100FULL;
+	if (advertise & ADVERTISED_Pause)
+		adv |= ADVERTISE_PAUSE_CAP;
+	if (advertise & ADVERTISED_Asym_Pause)
+		adv |= ADVERTISE_PAUSE_ASYM;
+
+	if (adv != oldadv) {
+		err = phy_write(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE, adv);
+
+		if (err < 0)
+			return err;
+		changed = 1;
+	}
+
+	/* Configure gigabit if it's supported */
+	if (phydev->supported & (SUPPORTED_1000baseT_Half |
+				SUPPORTED_1000baseT_Full)) {
+		oldadv = adv = phy_read(phydev, MDIO_DEVAD_NONE, MII_CTRL1000);
+
+		if (adv < 0)
+			return adv;
+
+		adv &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF);
+		if (advertise & SUPPORTED_1000baseT_Half)
+			adv |= ADVERTISE_1000HALF;
+		if (advertise & SUPPORTED_1000baseT_Full)
+			adv |= ADVERTISE_1000FULL;
+
+		if (adv != oldadv) {
+			err = phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000,
+					adv);
+
+			if (err < 0)
+				return err;
+			changed = 1;
+		}
+	}
+
+	return changed;
+}
+
+
+/**
+ * genphy_setup_forced - configures/forces speed/duplex from @phydev
+ * @phydev: target phy_device struct
+ *
+ * Description: Configures MII_BMCR to force speed/duplex
+ *   to the values in phydev. Assumes that the values are valid.
+ */
+int genphy_setup_forced(struct phy_device *phydev)
+{
+	int err;
+	int ctl = 0;
+
+	phydev->pause = phydev->asym_pause = 0;
+
+	if (SPEED_1000 == phydev->speed)
+		ctl |= BMCR_SPEED1000;
+	else if (SPEED_100 == phydev->speed)
+		ctl |= BMCR_SPEED100;
+
+	if (DUPLEX_FULL == phydev->duplex)
+		ctl |= BMCR_FULLDPLX;
+
+	err = phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl);
+
+	return err;
+}
+
+
+/**
+ * genphy_restart_aneg - Enable and Restart Autonegotiation
+ * @phydev: target phy_device struct
+ */
+int genphy_restart_aneg(struct phy_device *phydev)
+{
+	int ctl;
+
+	ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+	if (ctl < 0)
+		return ctl;
+
+	ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
+
+	/* Don't isolate the PHY if we're negotiating */
+	ctl &= ~(BMCR_ISOLATE);
+
+	ctl = phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl);
+
+	return ctl;
+}
+
+
+/**
+ * genphy_config_aneg - restart auto-negotiation or write BMCR
+ * @phydev: target phy_device struct
+ *
+ * Description: If auto-negotiation is enabled, we configure the
+ *   advertising, and then restart auto-negotiation.  If it is not
+ *   enabled, then we write the BMCR.
+ */
+int genphy_config_aneg(struct phy_device *phydev)
+{
+	int result;
+
+	if (AUTONEG_ENABLE != phydev->autoneg)
+		return genphy_setup_forced(phydev);
+
+	result = genphy_config_advert(phydev);
+
+	if (result < 0) /* error */
+		return result;
+
+	if (result == 0) {
+		/* Advertisment hasn't changed, but maybe aneg was never on to
+		 * begin with?  Or maybe phy was isolated? */
+		int ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+		if (ctl < 0)
+			return ctl;
+
+		if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE))
+			result = 1; /* do restart aneg */
+	}
+
+	/* Only restart aneg if we are advertising something different
+	 * than we were before.	 */
+	if (result > 0)
+		result = genphy_restart_aneg(phydev);
+
+	return result;
+}
+
+/**
+ * genphy_update_link - update link status in @phydev
+ * @phydev: target phy_device struct
+ *
+ * Description: Update the value in phydev->link to reflect the
+ *   current link value.  In order to do this, we need to read
+ *   the status register twice, keeping the second value.
+ */
+int genphy_update_link(struct phy_device *phydev)
+{
+	unsigned int mii_reg;
+
+	/*
+	 * Wait if the link is up, and autonegotiation is in progress
+	 * (ie - we're capable and it's not done)
+	 */
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+	/*
+	 * If we already saw the link up, and it hasn't gone down, then
+	 * we don't need to wait for autoneg again
+	 */
+	if (phydev->link && mii_reg & BMSR_LSTATUS)
+		return 0;
+
+	if ((mii_reg & BMSR_ANEGCAPABLE) && !(mii_reg & BMSR_ANEGCOMPLETE)) {
+		int i = 0;
+
+		printf("%s Waiting for PHY auto negotiation to complete",
+			phydev->dev->name);
+		while (!(mii_reg & BMSR_ANEGCOMPLETE)) {
+			/*
+			 * Timeout reached ?
+			 */
+			if (i > PHY_ANEG_TIMEOUT) {
+				printf(" TIMEOUT !\n");
+				phydev->link = 0;
+				return 0;
+			}
+
+			if (ctrlc()) {
+				puts("user interrupt!\n");
+				phydev->link = 0;
+				return -EINTR;
+			}
+
+			if ((i++ % 500) == 0)
+				printf(".");
+
+			udelay(1000);	/* 1 ms */
+			mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+		}
+		printf(" done\n");
+		phydev->link = 1;
+	} else {
+		/* Read the link a second time to clear the latched state */
+		mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+		if (mii_reg & BMSR_LSTATUS)
+			phydev->link = 1;
+		else
+			phydev->link = 0;
+	}
+
+	return 0;
+}
+
+/*
+ * Generic function which updates the speed and duplex.  If
+ * autonegotiation is enabled, it uses the AND of the link
+ * partner's advertised capabilities and our advertised
+ * capabilities.  If autonegotiation is disabled, we use the
+ * appropriate bits in the control register.
+ *
+ * Stolen from Linux's mii.c and phy_device.c
+ */
+static int genphy_parse_link(struct phy_device *phydev)
+{
+	int mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+	/* We're using autonegotiation */
+	if (mii_reg & BMSR_ANEGCAPABLE) {
+		u32 lpa = 0;
+		u32 gblpa = 0;
+
+		/* Check for gigabit capability */
+		if (mii_reg & BMSR_ERCAP) {
+			/* We want a list of states supported by
+			 * both PHYs in the link
+			 */
+			gblpa = phy_read(phydev, MDIO_DEVAD_NONE, MII_STAT1000);
+			gblpa &= phy_read(phydev,
+					MDIO_DEVAD_NONE, MII_CTRL1000) << 2;
+		}
+
+		/* Set the baseline so we only have to set them
+		 * if they're different
+		 */
+		phydev->speed = SPEED_10;
+		phydev->duplex = DUPLEX_HALF;
+
+		/* Check the gigabit fields */
+		if (gblpa & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) {
+			phydev->speed = SPEED_1000;
+
+			if (gblpa & PHY_1000BTSR_1000FD)
+				phydev->duplex = DUPLEX_FULL;
+
+			/* We're done! */
+			return 0;
+		}
+
+		lpa = phy_read(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE);
+		lpa &= phy_read(phydev, MDIO_DEVAD_NONE, MII_LPA);
+
+		if (lpa & (LPA_100FULL | LPA_100HALF)) {
+			phydev->speed = SPEED_100;
+
+			if (lpa & LPA_100FULL)
+				phydev->duplex = DUPLEX_FULL;
+
+		} else if (lpa & LPA_10FULL)
+			phydev->duplex = DUPLEX_FULL;
+	} else {
+		u32 bmcr = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+		phydev->speed = SPEED_10;
+		phydev->duplex = DUPLEX_HALF;
+
+		if (bmcr & BMCR_FULLDPLX)
+			phydev->duplex = DUPLEX_FULL;
+
+		if (bmcr & BMCR_SPEED1000)
+			phydev->speed = SPEED_1000;
+		else if (bmcr & BMCR_SPEED100)
+			phydev->speed = SPEED_100;
+	}
+
+	return 0;
+}
+
+int genphy_config(struct phy_device *phydev)
+{
+	int val;
+	u32 features;
+
+	/* For now, I'll claim that the generic driver supports
+	 * all possible port types */
+	features = (SUPPORTED_TP | SUPPORTED_MII
+			| SUPPORTED_AUI | SUPPORTED_FIBRE |
+			SUPPORTED_BNC);
+
+	/* Do we support autonegotiation? */
+	val = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+	if (val < 0)
+		return val;
+
+	if (val & BMSR_ANEGCAPABLE)
+		features |= SUPPORTED_Autoneg;
+
+	if (val & BMSR_100FULL)
+		features |= SUPPORTED_100baseT_Full;
+	if (val & BMSR_100HALF)
+		features |= SUPPORTED_100baseT_Half;
+	if (val & BMSR_10FULL)
+		features |= SUPPORTED_10baseT_Full;
+	if (val & BMSR_10HALF)
+		features |= SUPPORTED_10baseT_Half;
+
+	if (val & BMSR_ESTATEN) {
+		val = phy_read(phydev, MDIO_DEVAD_NONE, MII_ESTATUS);
+
+		if (val < 0)
+			return val;
+
+		if (val & ESTATUS_1000_TFULL)
+			features |= SUPPORTED_1000baseT_Full;
+		if (val & ESTATUS_1000_THALF)
+			features |= SUPPORTED_1000baseT_Half;
+	}
+
+	phydev->supported = features;
+	phydev->advertising = features;
+
+	genphy_config_aneg(phydev);
+
+	return 0;
+}
+
+int genphy_startup(struct phy_device *phydev)
+{
+	genphy_update_link(phydev);
+	genphy_parse_link(phydev);
+
+	return 0;
+}
+
+int genphy_shutdown(struct phy_device *phydev)
+{
+	return 0;
+}
+
+static struct phy_driver genphy_driver = {
+	.uid		= 0xffffffff,
+	.mask		= 0xffffffff,
+	.name		= "Generic PHY",
+	.features	= 0,
+	.config		= genphy_config,
+	.startup	= genphy_startup,
+	.shutdown	= genphy_shutdown,
+};
+
+static LIST_HEAD(phy_drivers);
+
+int phy_init(void)
+{
+#ifdef CONFIG_PHY_ATHEROS
+	phy_atheros_init();
+#endif
+#ifdef CONFIG_PHY_BROADCOM
+	phy_broadcom_init();
+#endif
+#ifdef CONFIG_PHY_DAVICOM
+	phy_davicom_init();
+#endif
+#ifdef CONFIG_PHY_LXT
+	phy_lxt_init();
+#endif
+#ifdef CONFIG_PHY_MARVELL
+	phy_marvell_init();
+#endif
+#ifdef CONFIG_PHY_MICREL
+	phy_micrel_init();
+#endif
+#ifdef CONFIG_PHY_NATSEMI
+	phy_natsemi_init();
+#endif
+#ifdef CONFIG_PHY_REALTEK
+	phy_realtek_init();
+#endif
+#ifdef CONFIG_PHY_TERANETICS
+	phy_teranetics_init();
+#endif
+#ifdef CONFIG_PHY_VITESSE
+	phy_vitesse_init();
+#endif
+
+	return 0;
+}
+
+int phy_register(struct phy_driver *drv)
+{
+	INIT_LIST_HEAD(&drv->list);
+	list_add_tail(&drv->list, &phy_drivers);
+
+	return 0;
+}
+
+int phy_probe(struct phy_device *phydev)
+{
+	int err = 0;
+
+	phydev->advertising = phydev->supported = phydev->drv->features;
+	phydev->mmds = phydev->drv->mmds;
+
+	if (phydev->drv->probe)
+		err = phydev->drv->probe(phydev);
+
+	return err;
+}
+
+static struct phy_driver *generic_for_interface(phy_interface_t interface)
+{
+#ifdef CONFIG_PHYLIB_10G
+	if (is_10g_interface(interface))
+		return &gen10g_driver;
+#endif
+
+	return &genphy_driver;
+}
+
+struct phy_driver *get_phy_driver(struct phy_device *phydev,
+				phy_interface_t interface)
+{
+	struct list_head *entry;
+	int phy_id = phydev->phy_id;
+	struct phy_driver *drv = NULL;
+
+	list_for_each(entry, &phy_drivers) {
+		drv = list_entry(entry, struct phy_driver, list);
+		if ((drv->uid & drv->mask) == (phy_id & drv->mask))
+			return drv;
+	}
+
+	/* If we made it here, there's no driver for this PHY */
+	return generic_for_interface(interface);
+}
+
+struct phy_device *phy_device_create(struct mii_dev *bus, int addr, int phy_id,
+					phy_interface_t interface)
+{
+	struct phy_device *dev;
+
+	/* We allocate the device, and initialize the
+	 * default values */
+	dev = malloc(sizeof(*dev));
+	if (!dev) {
+		printf("Failed to allocate PHY device for %s:%d\n",
+			bus->name, addr);
+		return NULL;
+	}
+
+	memset(dev, 0, sizeof(*dev));
+
+	dev->duplex = -1;
+	dev->link = 1;
+	dev->interface = interface;
+
+	dev->autoneg = AUTONEG_ENABLE;
+
+	dev->addr = addr;
+	dev->phy_id = phy_id;
+	dev->bus = bus;
+
+	dev->drv = get_phy_driver(dev, interface);
+
+	phy_probe(dev);
+
+	bus->phymap[addr] = dev;
+
+	return dev;
+}
+
+/**
+ * get_phy_id - reads the specified addr for its ID.
+ * @bus: the target MII bus
+ * @addr: PHY address on the MII bus
+ * @phy_id: where to store the ID retrieved.
+ *
+ * Description: Reads the ID registers of the PHY at @addr on the
+ *   @bus, stores it in @phy_id and returns zero on success.
+ */
+int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
+{
+	int phy_reg;
+
+	/* Grab the bits from PHYIR1, and put them
+	 * in the upper half */
+	phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);
+
+	if (phy_reg < 0)
+		return -EIO;
+
+	*phy_id = (phy_reg & 0xffff) << 16;
+
+	/* Grab the bits from PHYIR2, and put them in the lower half */
+	phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);
+
+	if (phy_reg < 0)
+		return -EIO;
+
+	*phy_id |= (phy_reg & 0xffff);
+
+	return 0;
+}
+
+/**
+ * get_phy_device - reads the specified PHY device and returns its @phy_device struct
+ * @bus: the target MII bus
+ * @addr: PHY address on the MII bus
+ *
+ * Description: Reads the ID registers of the PHY at @addr on the
+ *   @bus, then allocates and returns the phy_device to represent it.
+ */
+struct phy_device *get_phy_device(struct mii_dev *bus, int addr,
+				phy_interface_t interface)
+{
+	u32 phy_id = 0x1fffffff;
+	int i;
+	int r;
+
+	/* If we have one, return the existing device, with new interface */
+	if (bus->phymap[addr]) {
+		bus->phymap[addr]->interface = interface;
+
+		return bus->phymap[addr];
+	}
+
+	/* Try Standard (ie Clause 22) access */
+	r = get_phy_id(bus, addr, MDIO_DEVAD_NONE, &phy_id);
+	if (r)
+		return NULL;
+
+	/* If the PHY ID is mostly f's, we didn't find anything */
+	if ((phy_id & 0x1fffffff) != 0x1fffffff)
+		return phy_device_create(bus, addr, phy_id, interface);
+
+	/* Otherwise we have to try Clause 45 */
+	for (i = 1; i < 5; i++) {
+		r = get_phy_id(bus, addr, i, &phy_id);
+		if (r)
+			return NULL;
+
+		/* If the phy_id is mostly Fs, there is no device there */
+		if ((phy_id & 0x1fffffff) != 0x1fffffff)
+			break;
+	}
+
+	return phy_device_create(bus, addr, phy_id, interface);
+}
+
+int phy_reset(struct phy_device *phydev)
+{
+	int reg;
+	int timeout = 500;
+	int devad = MDIO_DEVAD_NONE;
+
+#ifdef CONFIG_PHYLIB_10G
+	/* If it's 10G, we need to issue reset through one of the MMDs */
+	if (is_10g_interface(phydev->interface)) {
+		if (!phydev->mmds)
+			gen10g_discover_mmds(phydev);
+
+		devad = ffs(phydev->mmds) - 1;
+	}
+#endif
+
+	reg = phy_read(phydev, devad, MII_BMCR);
+	if (reg < 0) {
+		debug("PHY status read failed\n");
+		return -1;
+	}
+
+	reg |= BMCR_RESET;
+
+	if (phy_write(phydev, devad, MII_BMCR, reg) < 0) {
+		debug("PHY reset failed\n");
+		return -1;
+	}
+
+#ifdef CONFIG_PHY_RESET_DELAY
+	udelay(CONFIG_PHY_RESET_DELAY);	/* Intel LXT971A needs this */
+#endif
+	/*
+	 * Poll the control register for the reset bit to go to 0 (it is
+	 * auto-clearing).  This should happen within 0.5 seconds per the
+	 * IEEE spec.
+	 */
+	while ((reg & BMCR_RESET) && timeout--) {
+		reg = phy_read(phydev, devad, MII_BMCR);
+
+		if (reg < 0) {
+			debug("PHY status read failed\n");
+			return -1;
+		}
+		udelay(1000);
+	}
+
+	if (reg & BMCR_RESET) {
+		puts("PHY reset timed out\n");
+		return -1;
+	}
+
+	return 0;
+}
+
+int miiphy_reset(const char *devname, unsigned char addr)
+{
+	struct mii_dev *bus = miiphy_get_dev_by_name(devname);
+	struct phy_device *phydev;
+
+	/*
+	 * miiphy_reset was only used on standard PHYs, so we'll fake it here.
+	 * If later code tries to connect with the right interface, this will
+	 * be corrected by get_phy_device in phy_connect()
+	 */
+	phydev = get_phy_device(bus, addr, PHY_INTERFACE_MODE_MII);
+
+	return phy_reset(phydev);
+}
+
+struct phy_device *phy_connect(struct mii_dev *bus, int addr,
+				struct eth_device *dev,
+				phy_interface_t interface)
+{
+	struct phy_device *phydev;
+
+	/* Reset the bus */
+	bus->reset(bus);
+
+	/* Wait 15ms to make sure the PHY has come out of hard reset */
+	udelay(15000);
+
+	phydev = get_phy_device(bus, addr, interface);
+
+	if (!phydev) {
+		printf("Could not get PHY for %s:%d\n", bus->name, addr);
+
+		return NULL;
+	}
+
+	/* Soft Reset the PHY */
+	phy_reset(phydev);
+
+	if (phydev->dev)
+		printf("%s:%d is connected to %s.  Reconnecting to %s\n",
+			bus->name, addr, phydev->dev->name, dev->name);
+
+	phydev->dev = dev;
+
+	printf("%s connected to %s\n", dev->name, phydev->drv->name);
+
+	return phydev;
+}
+
+int phy_startup(struct phy_device *phydev)
+{
+	if (phydev->drv->startup)
+		phydev->drv->startup(phydev);
+
+	return 0;
+}
+
+static int __board_phy_config(struct phy_device *phydev)
+{
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+	__attribute__((weak, alias("__board_phy_config")));
+
+int phy_config(struct phy_device *phydev)
+{
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	/* Invoke an optional board-specific helper */
+	board_phy_config(phydev);
+
+	return 0;
+}
+
+int phy_shutdown(struct phy_device *phydev)
+{
+	if (phydev->drv->shutdown)
+		phydev->drv->shutdown(phydev);
+
+	return 0;
+}
diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
new file mode 100644
index 0000000000..b7e2753f7b
--- /dev/null
+++ b/drivers/net/phy/realtek.c
@@ -0,0 +1,130 @@
+/*
+ * RealTek PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <config.h>
+#include <common.h>
+#include <phy.h>
+
+#define PHY_AUTONEGOTIATE_TIMEOUT 5000
+
+/* RTL8211B PHY Status Register */
+#define MIIM_RTL8211B_PHY_STATUS       0x11
+#define MIIM_RTL8211B_PHYSTAT_SPEED    0xc000
+#define MIIM_RTL8211B_PHYSTAT_GBIT     0x8000
+#define MIIM_RTL8211B_PHYSTAT_100      0x4000
+#define MIIM_RTL8211B_PHYSTAT_DUPLEX   0x2000
+#define MIIM_RTL8211B_PHYSTAT_SPDDONE  0x0800
+#define MIIM_RTL8211B_PHYSTAT_LINK     0x0400
+
+
+/* RealTek RTL8211B */
+static int rtl8211b_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, BMCR_RESET);
+
+	genphy_config_aneg(phydev);
+
+	return 0;
+}
+
+static int rtl8211b_parse_status(struct phy_device *phydev)
+{
+	unsigned int speed;
+	unsigned int mii_reg;
+
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211B_PHY_STATUS);
+
+	if (!(mii_reg & MIIM_RTL8211B_PHYSTAT_SPDDONE)) {
+		int i = 0;
+
+		/* in case of timeout ->link is cleared */
+		phydev->link = 1;
+		puts("Waiting for PHY realtime link");
+		while (!(mii_reg & MIIM_RTL8211B_PHYSTAT_SPDDONE)) {
+			/* Timeout reached ? */
+			if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
+				puts(" TIMEOUT !\n");
+				phydev->link = 0;
+				break;
+			}
+
+			if ((i++ % 1000) == 0)
+				putc('.');
+			udelay(1000);	/* 1 ms */
+			mii_reg = phy_read(phydev, MDIO_DEVAD_NONE,
+					MIIM_RTL8211B_PHY_STATUS);
+		}
+		puts(" done\n");
+		udelay(500000);	/* another 500 ms (results in faster booting) */
+	} else {
+		if (mii_reg & MIIM_RTL8211B_PHYSTAT_LINK)
+			phydev->link = 1;
+		else
+			phydev->link = 0;
+	}
+
+	if (mii_reg & MIIM_RTL8211B_PHYSTAT_DUPLEX)
+		phydev->duplex = DUPLEX_FULL;
+	else
+		phydev->duplex = DUPLEX_HALF;
+
+	speed = (mii_reg & MIIM_RTL8211B_PHYSTAT_SPEED);
+
+	switch (speed) {
+	case MIIM_RTL8211B_PHYSTAT_GBIT:
+		phydev->speed = SPEED_1000;
+		break;
+	case MIIM_RTL8211B_PHYSTAT_100:
+		phydev->speed = SPEED_100;
+		break;
+	default:
+		phydev->speed = SPEED_10;
+	}
+
+	return 0;
+}
+
+static int rtl8211b_startup(struct phy_device *phydev)
+{
+	/* Read the Status (2x to make sure link is right) */
+	genphy_update_link(phydev);
+	rtl8211b_parse_status(phydev);
+
+	return 0;
+}
+
+static struct phy_driver RTL8211B_driver = {
+	.name = "RealTek RTL8211B",
+	.uid = 0x1cc910,
+	.mask = 0xfffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &rtl8211b_config,
+	.startup = &rtl8211b_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+int phy_realtek_init(void)
+{
+	phy_register(&RTL8211B_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/teranetics.c b/drivers/net/phy/teranetics.c
new file mode 100644
index 0000000000..a771791b76
--- /dev/null
+++ b/drivers/net/phy/teranetics.c
@@ -0,0 +1,62 @@
+/*
+ * Teranetics PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <config.h>
+#include <phy.h>
+
+#ifndef CONFIG_PHYLIB_10G
+#error The Teranetics PHY needs 10G support
+#endif
+
+int tn2020_config(struct phy_device *phydev)
+{
+	if (phydev->port == PORT_FIBRE) {
+		unsigned short restart_an = (MDIO_AN_CTRL1_RESTART |
+						MDIO_AN_CTRL1_ENABLE |
+						MDIO_AN_CTRL1_XNP);
+
+		phy_write(phydev, 30, 93, 2);
+		phy_write(phydev, MDIO_MMD_AN, MDIO_CTRL1, restart_an);
+	}
+
+	return 0;
+}
+
+struct phy_driver tn2020_driver = {
+	.name = "Teranetics TN2020",
+	.uid = 0x00a19410,
+	.mask = 0xfffffff0,
+	.features = PHY_10G_FEATURES,
+	.mmds = (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
+			MDIO_DEVS_PHYXS | MDIO_DEVS_AN |
+			MDIO_DEVS_VEND1 | MDIO_DEVS_VEND2),
+	.config = &tn2020_config,
+	.startup = &gen10g_startup,
+	.shutdown = &gen10g_shutdown,
+};
+
+int phy_teranetics_init(void)
+{
+	phy_register(&tn2020_driver);
+
+	return 0;
+}
diff --git a/drivers/net/phy/vitesse.c b/drivers/net/phy/vitesse.c
new file mode 100644
index 0000000000..d48d4fe73f
--- /dev/null
+++ b/drivers/net/phy/vitesse.c
@@ -0,0 +1,242 @@
+/*
+ * Vitesse PHY drivers
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ */
+#include <miiphy.h>
+
+/* Cicada Auxiliary Control/Status Register */
+#define MIIM_CIS82xx_AUX_CONSTAT	0x1c
+#define MIIM_CIS82xx_AUXCONSTAT_INIT	0x0004
+#define MIIM_CIS82xx_AUXCONSTAT_DUPLEX	0x0020
+#define MIIM_CIS82xx_AUXCONSTAT_SPEED	0x0018
+#define MIIM_CIS82xx_AUXCONSTAT_GBIT	0x0010
+#define MIIM_CIS82xx_AUXCONSTAT_100	0x0008
+
+/* Cicada Extended Control Register 1 */
+#define MIIM_CIS82xx_EXT_CON1		0x17
+#define MIIM_CIS8201_EXTCON1_INIT	0x0000
+
+/* Cicada 8204 Extended PHY Control Register 1 */
+#define MIIM_CIS8204_EPHY_CON		0x17
+#define MIIM_CIS8204_EPHYCON_INIT	0x0006
+#define MIIM_CIS8204_EPHYCON_RGMII	0x1100
+
+/* Cicada 8204 Serial LED Control Register */
+#define MIIM_CIS8204_SLED_CON		0x1b
+#define MIIM_CIS8204_SLEDCON_INIT	0x1115
+
+/* Vitesse VSC8601 Extended PHY Control Register 1 */
+#define MIIM_VSC8601_EPHY_CON		0x17
+#define MIIM_VSC8601_EPHY_CON_INIT_SKEW	0x1120
+#define MIIM_VSC8601_SKEW_CTRL		0x1c
+
+#define PHY_EXT_PAGE_ACCESS    0x1f
+
+/* CIS8201 */
+static int vitesse_config(struct phy_device *phydev)
+{
+	/* Override PHY config settings */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_CIS82xx_AUX_CONSTAT,
+			MIIM_CIS82xx_AUXCONSTAT_INIT);
+	/* Set up the interface mode */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_CIS82xx_EXT_CON1,
+			MIIM_CIS8201_EXTCON1_INIT);
+
+	genphy_config_aneg(phydev);
+
+	return 0;
+}
+
+static int vitesse_parse_status(struct phy_device *phydev)
+{
+	int speed;
+	int mii_reg;
+
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_CIS82xx_AUX_CONSTAT);
+
+	if (mii_reg & MIIM_CIS82xx_AUXCONSTAT_DUPLEX)
+		phydev->duplex = DUPLEX_FULL;
+	else
+		phydev->duplex = DUPLEX_HALF;
+
+	speed = mii_reg & MIIM_CIS82xx_AUXCONSTAT_SPEED;
+	switch (speed) {
+	case MIIM_CIS82xx_AUXCONSTAT_GBIT:
+		phydev->speed = SPEED_1000;
+		break;
+	case MIIM_CIS82xx_AUXCONSTAT_100:
+		phydev->speed = SPEED_100;
+		break;
+	default:
+		phydev->speed = SPEED_10;
+		break;
+	}
+
+	return 0;
+}
+
+static int vitesse_startup(struct phy_device *phydev)
+{
+	genphy_update_link(phydev);
+	vitesse_parse_status(phydev);
+
+	return 0;
+}
+
+static int cis8204_config(struct phy_device *phydev)
+{
+	/* Override PHY config settings */
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_CIS82xx_AUX_CONSTAT,
+			MIIM_CIS82xx_AUXCONSTAT_INIT);
+
+	genphy_config_aneg(phydev);
+
+	if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) ||
+			(phydev->interface == PHY_INTERFACE_MODE_RGMII) ||
+			(phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) ||
+			(phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID))
+		phy_write(phydev, MDIO_DEVAD_NONE, MIIM_CIS8204_EPHY_CON,
+				MIIM_CIS8204_EPHYCON_INIT |
+				MIIM_CIS8204_EPHYCON_RGMII);
+	else
+		phy_write(phydev, MDIO_DEVAD_NONE, MIIM_CIS8204_EPHY_CON,
+				MIIM_CIS8204_EPHYCON_INIT);
+
+	return 0;
+}
+
+/* Vitesse VSC8601 */
+int vsc8601_config(struct phy_device *phydev)
+{
+	/* Configure some basic stuff */
+#ifdef CONFIG_SYS_VSC8601_SKEWFIX
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8601_EPHY_CON,
+			MIIM_VSC8601_EPHY_CON_INIT_SKEW);
+#if defined(CONFIG_SYS_VSC8601_SKEW_TX) && defined(CONFIG_SYS_VSC8601_SKEW_RX)
+	phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 1);
+#define VSC8101_SKEW \
+	((CONFIG_SYS_VSC8601_SKEW_TX << 14) \
+	| (CONFIG_SYS_VSC8601_SKEW_RX << 12))
+	phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8601_SKEW_CTRL,
+			VSC8101_SKEW);
+	phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 0);
+#endif
+#endif
+
+	genphy_config_aneg(phydev);
+
+	return 0;
+}
+
+static struct phy_driver VSC8211_driver = {
+	.name	= "Vitesse VSC8211",
+	.uid	= 0xfc4b0,
+	.mask	= 0xffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &vitesse_config,
+	.startup = &vitesse_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver VSC8221_driver = {
+	.name = "Vitesse VSC8221",
+	.uid = 0xfc550,
+	.mask = 0xffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &genphy_config_aneg,
+	.startup = &vitesse_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver VSC8244_driver = {
+	.name = "Vitesse VSC8244",
+	.uid = 0xfc6c0,
+	.mask = 0xffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &genphy_config_aneg,
+	.startup = &vitesse_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver VSC8234_driver = {
+	.name = "Vitesse VSC8234",
+	.uid = 0xfc620,
+	.mask = 0xffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &genphy_config_aneg,
+	.startup = &vitesse_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver VSC8601_driver = {
+	.name = "Vitesse VSC8601",
+	.uid = 0x70420,
+	.mask = 0xffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &vsc8601_config,
+	.startup = &vitesse_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver VSC8641_driver = {
+	.name = "Vitesse VSC8641",
+	.uid = 0x70430,
+	.mask = 0xffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &genphy_config_aneg,
+	.startup = &vitesse_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+/* Vitesse bought Cicada, so we'll put these here */
+static struct phy_driver cis8201_driver = {
+	.name = "CIS8201",
+	.uid = 0xfc410,
+	.mask = 0xffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &vitesse_config,
+	.startup = &vitesse_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver cis8204_driver = {
+	.name = "Cicada Cis8204",
+	.uid = 0xfc440,
+	.mask = 0xffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &cis8204_config,
+	.startup = &vitesse_startup,
+	.shutdown = &genphy_shutdown,
+};
+
+int phy_vitesse_init(void)
+{
+	phy_register(&VSC8641_driver);
+	phy_register(&VSC8601_driver);
+	phy_register(&VSC8234_driver);
+	phy_register(&VSC8244_driver);
+	phy_register(&VSC8211_driver);
+	phy_register(&VSC8221_driver);
+	phy_register(&cis8201_driver);
+	phy_register(&cis8204_driver);
+
+	return 0;
+}
diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c
index 9a91b9e0b8..06e5834a94 100644
--- a/drivers/net/tsec.c
+++ b/drivers/net/tsec.c
@@ -5,7 +5,7 @@
  * terms of the GNU Public License, Version 2, incorporated
  * herein by reference.
  *
- * Copyright 2004-2010 Freescale Semiconductor, Inc.
+ * Copyright 2004-2011 Freescale Semiconductor, Inc.
  * (C) Copyright 2003, Motorola, Inc.
  * author Andy Fleming
  *
@@ -17,10 +17,9 @@
 #include <net.h>
 #include <command.h>
 #include <tsec.h>
+#include <fsl_mdio.h>
 #include <asm/errno.h>
 
-#include "miiphy.h"
-
 DECLARE_GLOBAL_DATA_PTR;
 
 #define TX_BUF_CNT		2
@@ -44,31 +43,6 @@ static RTXBD rtx __attribute__ ((aligned(8)));
 #error "rtx must be 64-bit aligned"
 #endif
 
-static int tsec_send(struct eth_device *dev,
-		     volatile void *packet, int length);
-static int tsec_recv(struct eth_device *dev);
-static int tsec_init(struct eth_device *dev, bd_t * bd);
-static int tsec_initialize(bd_t * bis, struct tsec_info_struct *tsec_info);
-static void tsec_halt(struct eth_device *dev);
-static void init_registers(volatile tsec_t * regs);
-static void startup_tsec(struct eth_device *dev);
-static int init_phy(struct eth_device *dev);
-void write_phy_reg(struct tsec_private *priv, uint regnum, uint value);
-uint read_phy_reg(struct tsec_private *priv, uint regnum);
-static struct phy_info *get_phy_info(struct eth_device *dev);
-static void phy_run_commands(struct tsec_private *priv, struct phy_cmd *cmd);
-static void adjust_link(struct eth_device *dev);
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) \
-	&& !defined(BITBANGMII)
-static int tsec_miiphy_write(const char *devname, unsigned char addr,
-			     unsigned char reg, unsigned short value);
-static int tsec_miiphy_read(const char *devname, unsigned char addr,
-			    unsigned char reg, unsigned short *value);
-#endif
-#ifdef CONFIG_MCAST_TFTP
-static int tsec_mcast_addr (struct eth_device *dev, u8 mcast_mac, u8 set);
-#endif
-
 /* Default initializations for TSEC controllers. */
 
 static struct tsec_info_struct tsec_info[] = {
@@ -81,10 +55,10 @@ static struct tsec_info_struct tsec_info[] = {
 #ifdef CONFIG_MPC85XX_FEC
 	{
 		.regs = (tsec_t *)(TSEC_BASE_ADDR + 0x2000),
-		.miiregs = (tsec_mdio_t *)(MDIO_BASE_ADDR),
 		.devname = CONFIG_MPC85XX_FEC_NAME,
 		.phyaddr = FEC_PHY_ADDR,
-		.flags = FEC_FLAGS
+		.flags = FEC_FLAGS,
+		.mii_devname = DEFAULT_MII_NAME
 	},			/* FEC */
 #endif
 #ifdef CONFIG_TSEC3
@@ -95,195 +69,6 @@ static struct tsec_info_struct tsec_info[] = {
 #endif
 };
 
-/*
- * Initialize all the TSEC devices
- *
- * Returns the number of TSEC devices that were initialized
- */
-int tsec_eth_init(bd_t *bis, struct tsec_info_struct *tsecs, int num)
-{
-	int i;
-	int ret, count = 0;
-
-	for (i = 0; i < num; i++) {
-		ret = tsec_initialize(bis, &tsecs[i]);
-		if (ret > 0)
-			count += ret;
-	}
-
-	return count;
-}
-
-int tsec_standard_init(bd_t *bis)
-{
-	return tsec_eth_init(bis, tsec_info, ARRAY_SIZE(tsec_info));
-}
-
-/* Initialize device structure. Returns success if PHY
- * initialization succeeded (i.e. if it recognizes the PHY)
- */
-static int tsec_initialize(bd_t * bis, struct tsec_info_struct *tsec_info)
-{
-	struct eth_device *dev;
-	int i;
-	struct tsec_private *priv;
-
-	dev = (struct eth_device *)malloc(sizeof *dev);
-
-	if (NULL == dev)
-		return 0;
-
-	memset(dev, 0, sizeof *dev);
-
-	priv = (struct tsec_private *)malloc(sizeof(*priv));
-
-	if (NULL == priv)
-		return 0;
-
-	privlist[num_tsecs++] = priv;
-	priv->regs = tsec_info->regs;
-	priv->phyregs = tsec_info->miiregs;
-	priv->phyregs_sgmii = tsec_info->miiregs_sgmii;
-
-	priv->phyaddr = tsec_info->phyaddr;
-	priv->flags = tsec_info->flags;
-
-	sprintf(dev->name, tsec_info->devname);
-	dev->iobase = 0;
-	dev->priv = priv;
-	dev->init = tsec_init;
-	dev->halt = tsec_halt;
-	dev->send = tsec_send;
-	dev->recv = tsec_recv;
-#ifdef CONFIG_MCAST_TFTP
-	dev->mcast = tsec_mcast_addr;
-#endif
-
-	/* Tell u-boot to get the addr from the env */
-	for (i = 0; i < 6; i++)
-		dev->enetaddr[i] = 0;
-
-	eth_register(dev);
-
-	/* Reset the MAC */
-	priv->regs->maccfg1 |= MACCFG1_SOFT_RESET;
-	udelay(2);  /* Soft Reset must be asserted for 3 TX clocks */
-	priv->regs->maccfg1 &= ~(MACCFG1_SOFT_RESET);
-
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) \
-	&& !defined(BITBANGMII)
-	miiphy_register(dev->name, tsec_miiphy_read, tsec_miiphy_write);
-#endif
-
-	/* Try to initialize PHY here, and return */
-	return init_phy(dev);
-}
-
-/* Initializes data structures and registers for the controller,
- * and brings the interface up.	 Returns the link status, meaning
- * that it returns success if the link is up, failure otherwise.
- * This allows u-boot to find the first active controller.
- */
-static int tsec_init(struct eth_device *dev, bd_t * bd)
-{
-	uint tempval;
-	char tmpbuf[MAC_ADDR_LEN];
-	int i;
-	struct tsec_private *priv = (struct tsec_private *)dev->priv;
-	volatile tsec_t *regs = priv->regs;
-
-	/* Make sure the controller is stopped */
-	tsec_halt(dev);
-
-	/* Init MACCFG2.  Defaults to GMII */
-	regs->maccfg2 = MACCFG2_INIT_SETTINGS;
-
-	/* Init ECNTRL */
-	regs->ecntrl = ECNTRL_INIT_SETTINGS;
-
-	/* Copy the station address into the address registers.
-	 * Backwards, because little endian MACS are dumb */
-	for (i = 0; i < MAC_ADDR_LEN; i++) {
-		tmpbuf[MAC_ADDR_LEN - 1 - i] = dev->enetaddr[i];
-	}
-	tempval = (tmpbuf[0] << 24) | (tmpbuf[1] << 16) | (tmpbuf[2] << 8) |
-		  tmpbuf[3];
-
-	regs->macstnaddr1 = tempval;
-
-	tempval = *((uint *) (tmpbuf + 4));
-
-	regs->macstnaddr2 = tempval;
-
-	/* reset the indices to zero */
-	rxIdx = 0;
-	txIdx = 0;
-
-	/* Clear out (for the most part) the other registers */
-	init_registers(regs);
-
-	/* Ready the device for tx/rx */
-	startup_tsec(dev);
-
-	/* If there's no link, fail */
-	return (priv->link ? 0 : -1);
-}
-
-/* Writes the given phy's reg with value, using the specified MDIO regs */
-static void tsec_local_mdio_write(volatile tsec_mdio_t *phyregs, uint addr,
-		uint reg, uint value)
-{
-	int timeout = 1000000;
-
-	phyregs->miimadd = (addr << 8) | reg;
-	phyregs->miimcon = value;
-	asm("sync");
-
-	timeout = 1000000;
-	while ((phyregs->miimind & MIIMIND_BUSY) && timeout--) ;
-}
-
-
-/* Provide the default behavior of writing the PHY of this ethernet device */
-#define write_phy_reg(priv, regnum, value) \
-	tsec_local_mdio_write(priv->phyregs,priv->phyaddr,regnum,value)
-
-/* Reads register regnum on the device's PHY through the
- * specified registers.	 It lowers and raises the read
- * command, and waits for the data to become valid (miimind
- * notvalid bit cleared), and the bus to cease activity (miimind
- * busy bit cleared), and then returns the value
- */
-static uint tsec_local_mdio_read(volatile tsec_mdio_t *phyregs,
-				uint phyid, uint regnum)
-{
-	uint value;
-
-	/* Put the address of the phy, and the register
-	 * number into MIIMADD */
-	phyregs->miimadd = (phyid << 8) | regnum;
-
-	/* Clear the command register, and wait */
-	phyregs->miimcom = 0;
-	asm("sync");
-
-	/* Initiate a read command, and wait */
-	phyregs->miimcom = MIIM_READ_COMMAND;
-	asm("sync");
-
-	/* Wait for the the indication that the read is done */
-	while ((phyregs->miimind & (MIIMIND_NOTVALID | MIIMIND_BUSY))) ;
-
-	/* Grab the value read from the PHY */
-	value = phyregs->miimstat;
-
-	return value;
-}
-
-/* #define to provide old read_phy_reg functionality without duplicating code */
-#define read_phy_reg(priv,regnum) \
-	tsec_local_mdio_read(priv->phyregs,priv->phyaddr,regnum)
-
 #define TBIANA_SETTINGS ( \
 		TBIANA_ASYMMETRIC_PAUSE \
 		| TBIANA_SYMMETRIC_PAUSE \
@@ -305,661 +90,150 @@ static void tsec_configure_serdes(struct tsec_private *priv)
 {
 	/* Access TBI PHY registers at given TSEC register offset as opposed
 	 * to the register offset used for external PHY accesses */
-	tsec_local_mdio_write(priv->phyregs_sgmii, priv->regs->tbipa, TBI_ANA,
-			TBIANA_SETTINGS);
-	tsec_local_mdio_write(priv->phyregs_sgmii, priv->regs->tbipa, TBI_TBICON,
-			TBICON_CLK_SELECT);
-	tsec_local_mdio_write(priv->phyregs_sgmii, priv->regs->tbipa, TBI_CR,
-			CONFIG_TSEC_TBICR_SETTINGS);
-}
-
-/* Discover which PHY is attached to the device, and configure it
- * properly.  If the PHY is not recognized, then return 0
- * (failure).  Otherwise, return 1
- */
-static int init_phy(struct eth_device *dev)
-{
-	struct tsec_private *priv = (struct tsec_private *)dev->priv;
-	struct phy_info *curphy;
-	volatile tsec_t *regs = priv->regs;
-
-	/* Assign a Physical address to the TBI */
-	regs->tbipa = CONFIG_SYS_TBIPA_VALUE;
-	asm("sync");
-
-	/* Reset MII (due to new addresses) */
-	priv->phyregs->miimcfg = MIIMCFG_RESET;
-	asm("sync");
-	priv->phyregs->miimcfg = MIIMCFG_INIT_VALUE;
-	asm("sync");
-	while (priv->phyregs->miimind & MIIMIND_BUSY) ;
-
-	/* Get the cmd structure corresponding to the attached
-	 * PHY */
-	curphy = get_phy_info(dev);
-
-	if (curphy == NULL) {
-		priv->phyinfo = NULL;
-		printf("%s: No PHY found\n", dev->name);
-
-		return 0;
-	}
-
-	if (regs->ecntrl & ECNTRL_SGMII_MODE)
-		tsec_configure_serdes(priv);
-
-	priv->phyinfo = curphy;
-
-	phy_run_commands(priv, priv->phyinfo->config);
-
-	return 1;
-}
-
-/*
- * Returns which value to write to the control register.
- * For 10/100, the value is slightly different
- */
-static uint mii_cr_init(uint mii_reg, struct tsec_private * priv)
-{
-	if (priv->flags & TSEC_GIGABIT)
-		return MIIM_CONTROL_INIT;
-	else
-		return MIIM_CR_INIT;
+	tsec_local_mdio_write(priv->phyregs_sgmii, in_be32(&priv->regs->tbipa),
+			0, TBI_ANA, TBIANA_SETTINGS);
+	tsec_local_mdio_write(priv->phyregs_sgmii, in_be32(&priv->regs->tbipa),
+			0, TBI_TBICON, TBICON_CLK_SELECT);
+	tsec_local_mdio_write(priv->phyregs_sgmii, in_be32(&priv->regs->tbipa),
+			0, TBI_CR, CONFIG_TSEC_TBICR_SETTINGS);
 }
 
-/*
- * Wait for auto-negotiation to complete, then determine link
- */
-static uint mii_parse_sr(uint mii_reg, struct tsec_private * priv)
-{
-	/*
-	 * Wait if the link is up, and autonegotiation is in progress
-	 * (ie - we're capable and it's not done)
-	 */
-	mii_reg = read_phy_reg(priv, MIIM_STATUS);
-	if ((mii_reg & BMSR_ANEGCAPABLE) && !(mii_reg & BMSR_ANEGCOMPLETE)) {
-		int i = 0;
-
-		puts("Waiting for PHY auto negotiation to complete");
-		while (!(mii_reg & BMSR_ANEGCOMPLETE)) {
-			/*
-			 * Timeout reached ?
-			 */
-			if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
-				puts(" TIMEOUT !\n");
-				priv->link = 0;
-				return 0;
-			}
-
-			if (ctrlc()) {
-				puts("user interrupt!\n");
-				priv->link = 0;
-				return -EINTR;
-			}
-
-			if ((i++ % 1000) == 0) {
-				putc('.');
-			}
-			udelay(1000);	/* 1 ms */
-			mii_reg = read_phy_reg(priv, MIIM_STATUS);
-		}
-		puts(" done\n");
-
-		/* Link status bit is latched low, read it again */
-		mii_reg = read_phy_reg(priv, MIIM_STATUS);
-
-		udelay(500000);	/* another 500 ms (results in faster booting) */
-	}
+#ifdef CONFIG_MCAST_TFTP
 
-	priv->link = mii_reg & MIIM_STATUS_LINK ? 1 : 0;
+/* CREDITS: linux gianfar driver, slightly adjusted... thanx. */
 
-	return 0;
-}
+/* Set the appropriate hash bit for the given addr */
 
-/* Generic function which updates the speed and duplex.  If
- * autonegotiation is enabled, it uses the AND of the link
- * partner's advertised capabilities and our advertised
- * capabilities.  If autonegotiation is disabled, we use the
- * appropriate bits in the control register.
- *
- * Stolen from Linux's mii.c and phy_device.c
- */
-static uint mii_parse_link(uint mii_reg, struct tsec_private *priv)
+/* The algorithm works like so:
+ * 1) Take the Destination Address (ie the multicast address), and
+ * do a CRC on it (little endian), and reverse the bits of the
+ * result.
+ * 2) Use the 8 most significant bits as a hash into a 256-entry
+ * table.  The table is controlled through 8 32-bit registers:
+ * gaddr0-7.  gaddr0's MSB is entry 0, and gaddr7's LSB is
+ * gaddr7.  This means that the 3 most significant bits in the
+ * hash index which gaddr register to use, and the 5 other bits
+ * indicate which bit (assuming an IBM numbering scheme, which
+ * for PowerPC (tm) is usually the case) in the tregister holds
+ * the entry. */
+static int
+tsec_mcast_addr (struct eth_device *dev, u8 mcast_mac, u8 set)
 {
-	/* We're using autonegotiation */
-	if (mii_reg & BMSR_ANEGCAPABLE) {
-		uint lpa = 0;
-		uint gblpa = 0;
-
-		/* Check for gigabit capability */
-		if (mii_reg & BMSR_ERCAP) {
-			/* We want a list of states supported by
-			 * both PHYs in the link
-			 */
-			gblpa = read_phy_reg(priv, MII_STAT1000);
-			gblpa &= read_phy_reg(priv, MII_CTRL1000) << 2;
-		}
-
-		/* Set the baseline so we only have to set them
-		 * if they're different
-		 */
-		priv->speed = 10;
-		priv->duplexity = 0;
-
-		/* Check the gigabit fields */
-		if (gblpa & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) {
-			priv->speed = 1000;
-
-			if (gblpa & PHY_1000BTSR_1000FD)
-				priv->duplexity = 1;
-
-			/* We're done! */
-			return 0;
-		}
-
-		lpa = read_phy_reg(priv, MII_ADVERTISE);
-		lpa &= read_phy_reg(priv, MII_LPA);
+	struct tsec_private *priv = privlist[1];
+	volatile tsec_t *regs = priv->regs;
+	volatile u32  *reg_array, value;
+	u8 result, whichbit, whichreg;
 
-		if (lpa & (LPA_100FULL | LPA_100HALF)) {
-			priv->speed = 100;
+	result = (u8)((ether_crc(MAC_ADDR_LEN,mcast_mac) >> 24) & 0xff);
+	whichbit = result & 0x1f;	/* the 5 LSB = which bit to set */
+	whichreg = result >> 5;		/* the 3 MSB = which reg to set it in */
+	value = (1 << (31-whichbit));
 
-			if (lpa & LPA_100FULL)
-				priv->duplexity = 1;
+	reg_array = &(regs->hash.gaddr0);
 
-		} else if (lpa & LPA_10FULL)
-			priv->duplexity = 1;
+	if (set) {
+		reg_array[whichreg] |= value;
 	} else {
-		uint bmcr = read_phy_reg(priv, MII_BMCR);
-
-		priv->speed = 10;
-		priv->duplexity = 0;
-
-		if (bmcr & BMCR_FULLDPLX)
-			priv->duplexity = 1;
-
-		if (bmcr & BMCR_SPEED1000)
-			priv->speed = 1000;
-		else if (bmcr & BMCR_SPEED100)
-			priv->speed = 100;
-	}
-
-	return 0;
-}
-
-/*
- * "Ethernet@Wirespeed" needs to be enabled to achieve link in certain
- * circumstances.  eg a gigabit TSEC connected to a gigabit switch with
- * a 4-wire ethernet cable.  Both ends advertise gigabit, but can't
- * link.  "Ethernet@Wirespeed" reduces advertised speed until link
- * can be achieved.
- */
-static uint mii_BCM54xx_wirespeed(uint mii_reg, struct tsec_private *priv)
-{
-	return (read_phy_reg(priv, mii_reg) & 0x8FFF) | 0x8010;
-}
-
-/*
- * Parse the BCM54xx status register for speed and duplex information.
- * The linux sungem_phy has this information, but in a table format.
- */
-static uint mii_parse_BCM54xx_sr(uint mii_reg, struct tsec_private *priv)
-{
-	/* If there is no link, speed and duplex don't matter */
-	if (!priv->link)
-		return 0;
-
-	switch ((mii_reg & MIIM_BCM54xx_AUXSTATUS_LINKMODE_MASK) >>
-		MIIM_BCM54xx_AUXSTATUS_LINKMODE_SHIFT) {
-	case 1:
-		priv->duplexity = 0;
-		priv->speed = 10;
-		break;
-	case 2:
-		priv->duplexity = 1;
-		priv->speed = 10;
-		break;
-	case 3:
-		priv->duplexity = 0;
-		priv->speed = 100;
-		break;
-	case 5:
-		priv->duplexity = 1;
-		priv->speed = 100;
-		break;
-	case 6:
-		priv->duplexity = 0;
-		priv->speed = 1000;
-		break;
-	case 7:
-		priv->duplexity = 1;
-		priv->speed = 1000;
-		break;
-	default:
-		printf("Auto-neg error, defaulting to 10BT/HD\n");
-		priv->duplexity = 0;
-		priv->speed = 10;
-		break;
+		reg_array[whichreg] &= ~value;
 	}
-
 	return 0;
 }
+#endif /* Multicast TFTP ? */
 
-/*
- * Find out if PHY is in copper or serdes mode by looking at Expansion Reg
- * 0x42 - "Operating Mode Status Register"
- */
-static int BCM8482_is_serdes(struct tsec_private *priv)
-{
-	u16 val;
-	int serdes = 0;
-
-	write_phy_reg(priv, MIIM_BCM54XX_EXP_SEL, MIIM_BCM54XX_EXP_SEL_ER | 0x42);
-	val = read_phy_reg(priv, MIIM_BCM54XX_EXP_DATA);
-
-	switch (val & 0x1f) {
-	case 0x0d:	/* RGMII-to-100Base-FX */
-	case 0x0e:	/* RGMII-to-SGMII */
-	case 0x0f:	/* RGMII-to-SerDes */
-	case 0x12:	/* SGMII-to-SerDes */
-	case 0x13:	/* SGMII-to-100Base-FX */
-	case 0x16:	/* SerDes-to-Serdes */
-		serdes = 1;
-		break;
-	case 0x6:	/* RGMII-to-Copper */
-	case 0x14:	/* SGMII-to-Copper */
-	case 0x17:	/* SerDes-to-Copper */
-		break;
-	default:
-		printf("ERROR, invalid PHY mode (0x%x\n)", val);
-		break;
-	}
-
-	return serdes;
-}
-
-/*
- * Determine SerDes link speed and duplex from Expansion reg 0x42 "Operating
- * Mode Status Register"
+/* Initialized required registers to appropriate values, zeroing
+ * those we don't care about (unless zero is bad, in which case,
+ * choose a more appropriate value)
  */
-uint mii_parse_BCM5482_serdes_sr(struct tsec_private *priv)
+static void init_registers(tsec_t *regs)
 {
-	u16 val;
-	int i = 0;
+	/* Clear IEVENT */
+	out_be32(&regs->ievent, IEVENT_INIT_CLEAR);
+
+	out_be32(&regs->imask, IMASK_INIT_CLEAR);
+
+	out_be32(&regs->hash.iaddr0, 0);
+	out_be32(&regs->hash.iaddr1, 0);
+	out_be32(&regs->hash.iaddr2, 0);
+	out_be32(&regs->hash.iaddr3, 0);
+	out_be32(&regs->hash.iaddr4, 0);
+	out_be32(&regs->hash.iaddr5, 0);
+	out_be32(&regs->hash.iaddr6, 0);
+	out_be32(&regs->hash.iaddr7, 0);
+
+	out_be32(&regs->hash.gaddr0, 0);
+	out_be32(&regs->hash.gaddr1, 0);
+	out_be32(&regs->hash.gaddr2, 0);
+	out_be32(&regs->hash.gaddr3, 0);
+	out_be32(&regs->hash.gaddr4, 0);
+	out_be32(&regs->hash.gaddr5, 0);
+	out_be32(&regs->hash.gaddr6, 0);
+	out_be32(&regs->hash.gaddr7, 0);
+
+	out_be32(&regs->rctrl, 0x00000000);
 
-	/* Wait 1s for link - Clause 37 autonegotiation happens very fast */
-	while (1) {
-		write_phy_reg(priv, MIIM_BCM54XX_EXP_SEL,
-				MIIM_BCM54XX_EXP_SEL_ER | 0x42);
-		val = read_phy_reg(priv, MIIM_BCM54XX_EXP_DATA);
+	/* Init RMON mib registers */
+	memset((void *)&(regs->rmon), 0, sizeof(rmon_mib_t));
 
-		if (val & 0x8000)
-			break;
+	out_be32(&regs->rmon.cam1, 0xffffffff);
+	out_be32(&regs->rmon.cam2, 0xffffffff);
 
-		if (i++ > 1000) {
-			priv->link = 0;
-			return 1;
-		}
+	out_be32(&regs->mrblr, MRBLR_INIT_SETTINGS);
 
-		udelay(1000);	/* 1 ms */
-	}
+	out_be32(&regs->minflr, MINFLR_INIT_SETTINGS);
 
-	priv->link = 1;
-	switch ((val >> 13) & 0x3) {
-	case (0x00):
-		priv->speed = 10;
-		break;
-	case (0x01):
-		priv->speed = 100;
-		break;
-	case (0x02):
-		priv->speed = 1000;
-		break;
-	}
-
-	priv->duplexity = (val & 0x1000) == 0x1000;
+	out_be32(&regs->attr, ATTR_INIT_SETTINGS);
+	out_be32(&regs->attreli, ATTRELI_INIT_SETTINGS);
 
-	return 0;
 }
 
-/*
- * Figure out if BCM5482 is in serdes or copper mode and determine link
- * configuration accordingly
- */
-static uint mii_parse_BCM5482_sr(uint mii_reg, struct tsec_private *priv)
-{
-	if (BCM8482_is_serdes(priv)) {
-		mii_parse_BCM5482_serdes_sr(priv);
-		priv->flags |= TSEC_FIBER;
-	} else {
-		/* Wait for auto-negotiation to complete or fail */
-		mii_parse_sr(mii_reg, priv);
-
-		/* Parse BCM54xx copper aux status register */
-		mii_reg = read_phy_reg(priv, MIIM_BCM54xx_AUXSTATUS);
-		mii_parse_BCM54xx_sr(mii_reg, priv);
-	}
-
-	return 0;
-}
-
-/* Parse the 88E1011's status register for speed and duplex
- * information
- */
-static uint mii_parse_88E1011_psr(uint mii_reg, struct tsec_private * priv)
-{
-	uint speed;
-
-	mii_reg = read_phy_reg(priv, MIIM_88E1011_PHY_STATUS);
-
-	if ((mii_reg & MIIM_88E1011_PHYSTAT_LINK) &&
-		!(mii_reg & MIIM_88E1011_PHYSTAT_SPDDONE)) {
-		int i = 0;
-
-		puts("Waiting for PHY realtime link");
-		while (!(mii_reg & MIIM_88E1011_PHYSTAT_SPDDONE)) {
-			/* Timeout reached ? */
-			if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
-				puts(" TIMEOUT !\n");
-				priv->link = 0;
-				break;
-			}
-
-			if ((i++ % 1000) == 0) {
-				putc('.');
-			}
-			udelay(1000);	/* 1 ms */
-			mii_reg = read_phy_reg(priv, MIIM_88E1011_PHY_STATUS);
-		}
-		puts(" done\n");
-		udelay(500000);	/* another 500 ms (results in faster booting) */
-	} else {
-		if (mii_reg & MIIM_88E1011_PHYSTAT_LINK)
-			priv->link = 1;
-		else
-			priv->link = 0;
-	}
-
-	if (mii_reg & MIIM_88E1011_PHYSTAT_DUPLEX)
-		priv->duplexity = 1;
-	else
-		priv->duplexity = 0;
-
-	speed = (mii_reg & MIIM_88E1011_PHYSTAT_SPEED);
-
-	switch (speed) {
-	case MIIM_88E1011_PHYSTAT_GBIT:
-		priv->speed = 1000;
-		break;
-	case MIIM_88E1011_PHYSTAT_100:
-		priv->speed = 100;
-		break;
-	default:
-		priv->speed = 10;
-	}
-
-	return 0;
-}
-
-/* Parse the RTL8211B's status register for speed and duplex
- * information
+/* Configure maccfg2 based on negotiated speed and duplex
+ * reported by PHY handling code
  */
-static uint mii_parse_RTL8211B_sr(uint mii_reg, struct tsec_private * priv)
+static void adjust_link(struct tsec_private *priv, struct phy_device *phydev)
 {
-	uint speed;
-
-	mii_reg = read_phy_reg(priv, MIIM_RTL8211B_PHY_STATUS);
-	if (!(mii_reg & MIIM_RTL8211B_PHYSTAT_SPDDONE)) {
-		int i = 0;
-
-		/* in case of timeout ->link is cleared */
-		priv->link = 1;
-		puts("Waiting for PHY realtime link");
-		while (!(mii_reg & MIIM_RTL8211B_PHYSTAT_SPDDONE)) {
-			/* Timeout reached ? */
-			if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
-				puts(" TIMEOUT !\n");
-				priv->link = 0;
-				break;
-			}
-
-			if ((i++ % 1000) == 0) {
-				putc('.');
-			}
-			udelay(1000);	/* 1 ms */
-			mii_reg = read_phy_reg(priv, MIIM_RTL8211B_PHY_STATUS);
-		}
-		puts(" done\n");
-		udelay(500000);	/* another 500 ms (results in faster booting) */
-	} else {
-		if (mii_reg & MIIM_RTL8211B_PHYSTAT_LINK)
-			priv->link = 1;
-		else
-			priv->link = 0;
-	}
+	tsec_t *regs = priv->regs;
+	u32 ecntrl, maccfg2;
 
-	if (mii_reg & MIIM_RTL8211B_PHYSTAT_DUPLEX)
-		priv->duplexity = 1;
-	else
-		priv->duplexity = 0;
-
-	speed = (mii_reg & MIIM_RTL8211B_PHYSTAT_SPEED);
-
-	switch (speed) {
-	case MIIM_RTL8211B_PHYSTAT_GBIT:
-		priv->speed = 1000;
-		break;
-	case MIIM_RTL8211B_PHYSTAT_100:
-		priv->speed = 100;
-		break;
-	default:
-		priv->speed = 10;
+	if (!phydev->link) {
+		printf("%s: No link.\n", phydev->dev->name);
+		return;
 	}
 
-	return 0;
-}
+	/* clear all bits relative with interface mode */
+	ecntrl = in_be32(&regs->ecntrl);
+	ecntrl &= ~ECNTRL_R100;
 
-/* Parse the cis8201's status register for speed and duplex
- * information
- */
-static uint mii_parse_cis8201(uint mii_reg, struct tsec_private * priv)
-{
-	uint speed;
+	maccfg2 = in_be32(&regs->maccfg2);
+	maccfg2 &= ~(MACCFG2_IF | MACCFG2_FULL_DUPLEX);
 
-	if (mii_reg & MIIM_CIS8201_AUXCONSTAT_DUPLEX)
-		priv->duplexity = 1;
-	else
-		priv->duplexity = 0;
+	if (phydev->duplex)
+		maccfg2 |= MACCFG2_FULL_DUPLEX;
 
-	speed = mii_reg & MIIM_CIS8201_AUXCONSTAT_SPEED;
-	switch (speed) {
-	case MIIM_CIS8201_AUXCONSTAT_GBIT:
-		priv->speed = 1000;
+	switch (phydev->speed) {
+	case 1000:
+		maccfg2 |= MACCFG2_GMII;
 		break;
-	case MIIM_CIS8201_AUXCONSTAT_100:
-		priv->speed = 100;
-		break;
-	default:
-		priv->speed = 10;
-		break;
-	}
-
-	return 0;
-}
-
-/* Parse the vsc8244's status register for speed and duplex
- * information
- */
-static uint mii_parse_vsc8244(uint mii_reg, struct tsec_private * priv)
-{
-	uint speed;
+	case 100:
+	case 10:
+		maccfg2 |= MACCFG2_MII;
 
-	if (mii_reg & MIIM_VSC8244_AUXCONSTAT_DUPLEX)
-		priv->duplexity = 1;
-	else
-		priv->duplexity = 0;
-
-	speed = mii_reg & MIIM_VSC8244_AUXCONSTAT_SPEED;
-	switch (speed) {
-	case MIIM_VSC8244_AUXCONSTAT_GBIT:
-		priv->speed = 1000;
-		break;
-	case MIIM_VSC8244_AUXCONSTAT_100:
-		priv->speed = 100;
+		/* Set R100 bit in all modes although
+		 * it is only used in RGMII mode
+		 */
+		if (phydev->speed == 100)
+			ecntrl |= ECNTRL_R100;
 		break;
 	default:
-		priv->speed = 10;
+		printf("%s: Speed was bad\n", phydev->dev->name);
 		break;
 	}
 
-	return 0;
-}
-
-/* Parse the DM9161's status register for speed and duplex
- * information
- */
-static uint mii_parse_dm9161_scsr(uint mii_reg, struct tsec_private * priv)
-{
-	if (mii_reg & (MIIM_DM9161_SCSR_100F | MIIM_DM9161_SCSR_100H))
-		priv->speed = 100;
-	else
-		priv->speed = 10;
-
-	if (mii_reg & (MIIM_DM9161_SCSR_100F | MIIM_DM9161_SCSR_10F))
-		priv->duplexity = 1;
-	else
-		priv->duplexity = 0;
-
-	return 0;
-}
-
-/*
- * Hack to write all 4 PHYs with the LED values
- */
-static uint mii_cis8204_fixled(uint mii_reg, struct tsec_private * priv)
-{
-	uint phyid;
-	volatile tsec_mdio_t *regbase = priv->phyregs;
-	int timeout = 1000000;
-
-	for (phyid = 0; phyid < 4; phyid++) {
-		regbase->miimadd = (phyid << 8) | mii_reg;
-		regbase->miimcon = MIIM_CIS8204_SLEDCON_INIT;
-		asm("sync");
-
-		timeout = 1000000;
-		while ((regbase->miimind & MIIMIND_BUSY) && timeout--) ;
-	}
-
-	return MIIM_CIS8204_SLEDCON_INIT;
-}
-
-static uint mii_cis8204_setmode(uint mii_reg, struct tsec_private * priv)
-{
-	if (priv->flags & TSEC_REDUCED)
-		return MIIM_CIS8204_EPHYCON_INIT | MIIM_CIS8204_EPHYCON_RGMII;
-	else
-		return MIIM_CIS8204_EPHYCON_INIT;
-}
-
-static uint mii_m88e1111s_setmode(uint mii_reg, struct tsec_private *priv)
-{
-	uint mii_data = read_phy_reg(priv, mii_reg);
-
-	if (priv->flags & TSEC_REDUCED)
-		mii_data = (mii_data & 0xfff0) | 0x000b;
-	return mii_data;
-}
-
-/* Initialized required registers to appropriate values, zeroing
- * those we don't care about (unless zero is bad, in which case,
- * choose a more appropriate value)
- */
-static void init_registers(volatile tsec_t * regs)
-{
-	/* Clear IEVENT */
-	regs->ievent = IEVENT_INIT_CLEAR;
-
-	regs->imask = IMASK_INIT_CLEAR;
-
-	regs->hash.iaddr0 = 0;
-	regs->hash.iaddr1 = 0;
-	regs->hash.iaddr2 = 0;
-	regs->hash.iaddr3 = 0;
-	regs->hash.iaddr4 = 0;
-	regs->hash.iaddr5 = 0;
-	regs->hash.iaddr6 = 0;
-	regs->hash.iaddr7 = 0;
-
-	regs->hash.gaddr0 = 0;
-	regs->hash.gaddr1 = 0;
-	regs->hash.gaddr2 = 0;
-	regs->hash.gaddr3 = 0;
-	regs->hash.gaddr4 = 0;
-	regs->hash.gaddr5 = 0;
-	regs->hash.gaddr6 = 0;
-	regs->hash.gaddr7 = 0;
-
-	regs->rctrl = 0x00000000;
-
-	/* Init RMON mib registers */
-	memset((void *)&(regs->rmon), 0, sizeof(rmon_mib_t));
-
-	regs->rmon.cam1 = 0xffffffff;
-	regs->rmon.cam2 = 0xffffffff;
-
-	regs->mrblr = MRBLR_INIT_SETTINGS;
-
-	regs->minflr = MINFLR_INIT_SETTINGS;
-
-	regs->attr = ATTR_INIT_SETTINGS;
-	regs->attreli = ATTRELI_INIT_SETTINGS;
+	out_be32(&regs->ecntrl, ecntrl);
+	out_be32(&regs->maccfg2, maccfg2);
 
-}
-
-/* Configure maccfg2 based on negotiated speed and duplex
- * reported by PHY handling code
- */
-static void adjust_link(struct eth_device *dev)
-{
-	struct tsec_private *priv = (struct tsec_private *)dev->priv;
-	volatile tsec_t *regs = priv->regs;
-
-	if (priv->link) {
-		if (priv->duplexity != 0)
-			regs->maccfg2 |= MACCFG2_FULL_DUPLEX;
-		else
-			regs->maccfg2 &= ~(MACCFG2_FULL_DUPLEX);
-
-		switch (priv->speed) {
-		case 1000:
-			regs->maccfg2 = ((regs->maccfg2 & ~(MACCFG2_IF))
-					 | MACCFG2_GMII);
-			break;
-		case 100:
-		case 10:
-			regs->maccfg2 = ((regs->maccfg2 & ~(MACCFG2_IF))
-					 | MACCFG2_MII);
-
-			/* Set R100 bit in all modes although
-			 * it is only used in RGMII mode
-			 */
-			if (priv->speed == 100)
-				regs->ecntrl |= ECNTRL_R100;
-			else
-				regs->ecntrl &= ~(ECNTRL_R100);
-			break;
-		default:
-			printf("%s: Speed was bad\n", dev->name);
-			break;
-		}
-
-		printf("Speed: %d, %s duplex%s\n", priv->speed,
-		       (priv->duplexity) ? "full" : "half",
-		       (priv->flags & TSEC_FIBER) ? ", fiber mode" : "");
-
-	} else {
-		printf("%s: No link.\n", dev->name);
-	}
+	printf("Speed: %d, %s duplex%s\n", phydev->speed,
+			(phydev->duplex) ? "full" : "half",
+			(phydev->port == PORT_FIBRE) ? ", fiber mode" : "");
 }
 
 /* Set up the buffers and their descriptors, and bring up the
@@ -969,11 +243,15 @@ static void startup_tsec(struct eth_device *dev)
 {
 	int i;
 	struct tsec_private *priv = (struct tsec_private *)dev->priv;
-	volatile tsec_t *regs = priv->regs;
+	tsec_t *regs = priv->regs;
+
+	/* reset the indices to zero */
+	rxIdx = 0;
+	txIdx = 0;
 
 	/* Point to the buffer descriptors */
-	regs->tbase = (unsigned int)(&rtx.txbd[txIdx]);
-	regs->rbase = (unsigned int)(&rtx.rxbd[rxIdx]);
+	out_be32(&regs->tbase, (unsigned int)(&rtx.txbd[txIdx]));
+	out_be32(&regs->rbase, (unsigned int)(&rtx.rxbd[rxIdx]));
 
 	/* Initialize the Rx Buffer descriptors */
 	for (i = 0; i < PKTBUFSRX; i++) {
@@ -991,20 +269,14 @@ static void startup_tsec(struct eth_device *dev)
 	}
 	rtx.txbd[TX_BUF_CNT - 1].status |= TXBD_WRAP;
 
-	/* Start up the PHY */
-	if(priv->phyinfo)
-		phy_run_commands(priv, priv->phyinfo->startup);
-
-	adjust_link(dev);
-
 	/* Enable Transmit and Receive */
-	regs->maccfg1 |= (MACCFG1_RX_EN | MACCFG1_TX_EN);
+	setbits_be32(&regs->maccfg1, MACCFG1_RX_EN | MACCFG1_TX_EN);
 
 	/* Tell the DMA it is clear to go */
-	regs->dmactrl |= DMACTRL_INIT_SETTINGS;
-	regs->tstat = TSTAT_CLEAR_THALT;
-	regs->rstat = RSTAT_CLEAR_RHALT;
-	regs->dmactrl &= ~(DMACTRL_GRS | DMACTRL_GTS);
+	setbits_be32(&regs->dmactrl, DMACTRL_INIT_SETTINGS);
+	out_be32(&regs->tstat, TSTAT_CLEAR_THALT);
+	out_be32(&regs->rstat, RSTAT_CLEAR_RHALT);
+	clrbits_be32(&regs->dmactrl, DMACTRL_GRS | DMACTRL_GTS);
 }
 
 /* This returns the status bits of the device.	The return value
@@ -1017,7 +289,7 @@ static int tsec_send(struct eth_device *dev, volatile void *packet, int length)
 	int i;
 	int result = 0;
 	struct tsec_private *priv = (struct tsec_private *)dev->priv;
-	volatile tsec_t *regs = priv->regs;
+	tsec_t *regs = priv->regs;
 
 	/* Find an empty buffer descriptor */
 	for (i = 0; rtx.txbd[txIdx].status & TXBD_READY; i++) {
@@ -1033,7 +305,7 @@ static int tsec_send(struct eth_device *dev, volatile void *packet, int length)
 	    (TXBD_READY | TXBD_LAST | TXBD_CRC | TXBD_INTERRUPT);
 
 	/* Tell the DMA to go */
-	regs->tstat = TSTAT_CLEAR_THALT;
+	out_be32(&regs->tstat, TSTAT_CLEAR_THALT);
 
 	/* Wait for buffer to be transmitted */
 	for (i = 0; rtx.txbd[txIdx].status & TXBD_READY; i++) {
@@ -1053,7 +325,7 @@ static int tsec_recv(struct eth_device *dev)
 {
 	int length;
 	struct tsec_private *priv = (struct tsec_private *)dev->priv;
-	volatile tsec_t *regs = priv->regs;
+	tsec_t *regs = priv->regs;
 
 	while (!(rtx.rxbd[rxIdx].status & RXBD_EMPTY)) {
 
@@ -1076,9 +348,9 @@ static int tsec_recv(struct eth_device *dev)
 		rxIdx = (rxIdx + 1) % PKTBUFSRX;
 	}
 
-	if (regs->ievent & IEVENT_BSY) {
-		regs->ievent = IEVENT_BSY;
-		regs->rstat = RSTAT_CLEAR_RHALT;
+	if (in_be32(&regs->ievent) & IEVENT_BSY) {
+		out_be32(&regs->ievent, IEVENT_BSY);
+		out_be32(&regs->rstat, RSTAT_CLEAR_RHALT);
 	}
 
 	return -1;
@@ -1089,936 +361,236 @@ static int tsec_recv(struct eth_device *dev)
 static void tsec_halt(struct eth_device *dev)
 {
 	struct tsec_private *priv = (struct tsec_private *)dev->priv;
-	volatile tsec_t *regs = priv->regs;
+	tsec_t *regs = priv->regs;
 
-	regs->dmactrl &= ~(DMACTRL_GRS | DMACTRL_GTS);
-	regs->dmactrl |= (DMACTRL_GRS | DMACTRL_GTS);
+	clrbits_be32(&regs->dmactrl, DMACTRL_GRS | DMACTRL_GTS);
+	setbits_be32(&regs->dmactrl, DMACTRL_GRS | DMACTRL_GTS);
 
-	while ((regs->ievent & (IEVENT_GRSC | IEVENT_GTSC))
-		!= (IEVENT_GRSC | IEVENT_GTSC)) ;
+	while ((in_be32(&regs->ievent) & (IEVENT_GRSC | IEVENT_GTSC))
+			!= (IEVENT_GRSC | IEVENT_GTSC))
+		;
 
-	regs->maccfg1 &= ~(MACCFG1_TX_EN | MACCFG1_RX_EN);
+	clrbits_be32(&regs->maccfg1, MACCFG1_TX_EN | MACCFG1_RX_EN);
 
 	/* Shut down the PHY, as needed */
-	if(priv->phyinfo)
-		phy_run_commands(priv, priv->phyinfo->shutdown);
+	phy_shutdown(priv->phydev);
 }
 
-static struct phy_info phy_info_M88E1149S = {
-	0x1410ca,
-	"Marvell 88E1149S",
-	4,
-	(struct phy_cmd[]) {     /* config */
-		/* Reset and configure the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{0x1d, 0x1f, NULL},
-		{0x1e, 0x200c, NULL},
-		{0x1d, 0x5, NULL},
-		{0x1e, 0x0, NULL},
-		{0x1e, 0x100, NULL},
-		{MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL},
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {     /* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_88E1011_PHY_STATUS, miim_read, &mii_parse_88E1011_psr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {     /* shutdown */
-		{miim_end,}
-	},
-};
-
-/* The 5411 id is 0x206070, the 5421 is 0x2060e0 */
-static struct phy_info phy_info_BCM5461S = {
-	0x02060c1,	/* 5461 ID */
-	"Broadcom BCM5461S",
-	0, /* not clear to me what minor revisions we can shift away */
-	(struct phy_cmd[]) { /* config */
-		/* Reset and configure the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL},
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_BCM54xx_AUXSTATUS, miim_read, &mii_parse_BCM54xx_sr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* shutdown */
-		{miim_end,}
-	},
-};
-
-static struct phy_info phy_info_BCM5464S = {
-	0x02060b1,	/* 5464 ID */
-	"Broadcom BCM5464S",
-	0, /* not clear to me what minor revisions we can shift away */
-	(struct phy_cmd[]) { /* config */
-		/* Reset and configure the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL},
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_BCM54xx_AUXSTATUS, miim_read, &mii_parse_BCM54xx_sr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* shutdown */
-		{miim_end,}
-	},
-};
-
-static struct phy_info phy_info_BCM5482S =  {
-	0x0143bcb,
-	"Broadcom BCM5482S",
-	4,
-	(struct phy_cmd[]) { /* config */
-		/* Reset and configure the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		/* Setup read from auxilary control shadow register 7 */
-		{MIIM_BCM54xx_AUXCNTL, MIIM_BCM54xx_AUXCNTL_ENCODE(7), NULL},
-		/* Read Misc Control register and or in Ethernet@Wirespeed */
-		{MIIM_BCM54xx_AUXCNTL, 0, &mii_BCM54xx_wirespeed},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		/* Initial config/enable of secondary SerDes interface */
-		{MIIM_BCM54XX_SHD, MIIM_BCM54XX_SHD_WR_ENCODE(0x14, 0xf), NULL},
-		/* Write intial value to secondary SerDes Contol */
-		{MIIM_BCM54XX_EXP_SEL, MIIM_BCM54XX_EXP_SEL_SSD | 0, NULL},
-		{MIIM_BCM54XX_EXP_DATA, MIIM_CONTROL_RESTART, NULL},
-		/* Enable copper/fiber auto-detect */
-		{MIIM_BCM54XX_SHD, MIIM_BCM54XX_SHD_WR_ENCODE(0x1e, 0x201)},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Determine copper/fiber, auto-negotiate, and read the result */
-		{MIIM_STATUS, miim_read, &mii_parse_BCM5482_sr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* shutdown */
-		{miim_end,}
-	},
-};
-
-static struct phy_info phy_info_M88E1011S = {
-	0x01410c6,
-	"Marvell 88E1011S",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		/* Reset and configure the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{0x1d, 0x1f, NULL},
-		{0x1e, 0x200c, NULL},
-		{0x1d, 0x5, NULL},
-		{0x1e, 0x0, NULL},
-		{0x1e, 0x100, NULL},
-		{MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL},
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_88E1011_PHY_STATUS, miim_read, &mii_parse_88E1011_psr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
-
-static struct phy_info phy_info_M88E1111S = {
-	0x01410cc,
-	"Marvell 88E1111S",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		/* Reset and configure the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{0x1b, 0x848f, &mii_m88e1111s_setmode},
-		{0x14, 0x0cd2, NULL}, /* Delay RGMII TX and RX */
-		{MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL},
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_88E1011_PHY_STATUS, miim_read, &mii_parse_88E1011_psr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
-
-static struct phy_info phy_info_M88E1118 = {
-	0x01410e1,
-	"Marvell 88E1118",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		/* Reset and configure the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{0x16, 0x0002, NULL}, /* Change Page Number */
-		{0x15, 0x1070, NULL}, /* Delay RGMII TX and RX */
-		{0x16, 0x0003, NULL}, /* Change Page Number */
-		{0x10, 0x021e, NULL}, /* Adjust LED control */
-		{0x16, 0x0000, NULL}, /* Change Page Number */
-		{MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL},
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		{0x16, 0x0000, NULL}, /* Change Page Number */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_88E1011_PHY_STATUS, miim_read,
-		 &mii_parse_88E1011_psr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
-
-/*
- *  Since to access LED register we need do switch the page, we
- * do LED configuring in the miim_read-like function as follows
+/* Initializes data structures and registers for the controller,
+ * and brings the interface up.	 Returns the link status, meaning
+ * that it returns success if the link is up, failure otherwise.
+ * This allows u-boot to find the first active controller.
  */
-static uint mii_88E1121_set_led (uint mii_reg, struct tsec_private *priv)
+static int tsec_init(struct eth_device *dev, bd_t * bd)
 {
-	uint pg;
+	uint tempval;
+	char tmpbuf[MAC_ADDR_LEN];
+	int i;
+	struct tsec_private *priv = (struct tsec_private *)dev->priv;
+	tsec_t *regs = priv->regs;
 
-	/* Switch the page to access the led register */
-	pg = read_phy_reg(priv, MIIM_88E1121_PHY_PAGE);
-	write_phy_reg(priv, MIIM_88E1121_PHY_PAGE, MIIM_88E1121_PHY_LED_PAGE);
+	/* Make sure the controller is stopped */
+	tsec_halt(dev);
 
-	/* Configure leds */
-	write_phy_reg(priv, MIIM_88E1121_PHY_LED_CTRL,
-		      MIIM_88E1121_PHY_LED_DEF);
+	/* Init MACCFG2.  Defaults to GMII */
+	out_be32(&regs->maccfg2, MACCFG2_INIT_SETTINGS);
 
-	/* Restore the page pointer */
-	write_phy_reg(priv, MIIM_88E1121_PHY_PAGE, pg);
-	return 0;
-}
+	/* Init ECNTRL */
+	out_be32(&regs->ecntrl, ECNTRL_INIT_SETTINGS);
 
-static struct phy_info phy_info_M88E1121R = {
-	0x01410cb,
-	"Marvell 88E1121R",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		/* Reset and configure the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL},
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		/* Configure leds */
-		{MIIM_88E1121_PHY_LED_CTRL, miim_read, &mii_88E1121_set_led},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		/* Disable IRQs and de-assert interrupt */
-		{MIIM_88E1121_PHY_IRQ_EN, 0, NULL},
-		{MIIM_88E1121_PHY_IRQ_STATUS, miim_read, NULL},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		{MIIM_STATUS, miim_read, &mii_parse_link},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+	/* Copy the station address into the address registers.
+	 * Backwards, because little endian MACS are dumb */
+	for (i = 0; i < MAC_ADDR_LEN; i++)
+		tmpbuf[MAC_ADDR_LEN - 1 - i] = dev->enetaddr[i];
 
-static unsigned int m88e1145_setmode(uint mii_reg, struct tsec_private *priv)
-{
-	uint mii_data = read_phy_reg(priv, mii_reg);
-
-	/* Setting MIIM_88E1145_PHY_EXT_CR */
-	if (priv->flags & TSEC_REDUCED)
-		return mii_data |
-		    MIIM_M88E1145_RGMII_RX_DELAY | MIIM_M88E1145_RGMII_TX_DELAY;
-	else
-		return mii_data;
-}
+	tempval = (tmpbuf[0] << 24) | (tmpbuf[1] << 16) | (tmpbuf[2] << 8) |
+		  tmpbuf[3];
 
-static struct phy_info phy_info_M88E1145 = {
-	0x01410cd,
-	"Marvell 88E1145",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		/* Reset the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-
-		/* Errata E0, E1 */
-		{29, 0x001b, NULL},
-		{30, 0x418f, NULL},
-		{29, 0x0016, NULL},
-		{30, 0xa2da, NULL},
-
-		/* Configure the PHY */
-		{MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL},
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		{MIIM_88E1011_PHY_SCR, MIIM_88E1011_PHY_MDI_X_AUTO, NULL},
-		{MIIM_88E1145_PHY_EXT_CR, 0, &m88e1145_setmode},
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, NULL},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		{MIIM_88E1111_PHY_LED_CONTROL, MIIM_88E1111_PHY_LED_DIRECT, NULL},
-		/* Read the Status */
-		{MIIM_88E1011_PHY_STATUS, miim_read, &mii_parse_88E1011_psr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+	out_be32(&regs->macstnaddr1, tempval);
 
-static struct phy_info phy_info_cis8204 = {
-	0x3f11,
-	"Cicada Cis8204",
-	6,
-	(struct phy_cmd[]) {	/* config */
-		/* Override PHY config settings */
-		{MIIM_CIS8201_AUX_CONSTAT, MIIM_CIS8201_AUXCONSTAT_INIT, NULL},
-		/* Configure some basic stuff */
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{MIIM_CIS8204_SLED_CON, MIIM_CIS8204_SLEDCON_INIT,
-		 &mii_cis8204_fixled},
-		{MIIM_CIS8204_EPHY_CON, MIIM_CIS8204_EPHYCON_INIT,
-		 &mii_cis8204_setmode},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Read the Status (2x to make sure link is right) */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_CIS8201_AUX_CONSTAT, miim_read, &mii_parse_cis8201},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+	tempval = *((uint *) (tmpbuf + 4));
 
-/* Cicada 8201 */
-static struct phy_info phy_info_cis8201 = {
-	0xfc41,
-	"CIS8201",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		/* Override PHY config settings */
-		{MIIM_CIS8201_AUX_CONSTAT, MIIM_CIS8201_AUXCONSTAT_INIT, NULL},
-		/* Set up the interface mode */
-		{MIIM_CIS8201_EXT_CON1, MIIM_CIS8201_EXTCON1_INIT, NULL},
-		/* Configure some basic stuff */
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Read the Status (2x to make sure link is right) */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_CIS8201_AUX_CONSTAT, miim_read, &mii_parse_cis8201},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+	out_be32(&regs->macstnaddr2, tempval);
 
-static struct phy_info phy_info_VSC8211 = {
-	0xfc4b,
-	"Vitesse VSC8211",
-	4,
-	(struct phy_cmd[]) { /* config */
-		/* Override PHY config settings */
-		{MIIM_CIS8201_AUX_CONSTAT, MIIM_CIS8201_AUXCONSTAT_INIT, NULL},
-		/* Set up the interface mode */
-		{MIIM_CIS8201_EXT_CON1, MIIM_CIS8201_EXTCON1_INIT, NULL},
-		/* Configure some basic stuff */
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* startup */
-		/* Read the Status (2x to make sure link is right) */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_CIS8201_AUX_CONSTAT, miim_read, &mii_parse_cis8201},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* shutdown */
-		{miim_end,}
-	},
-};
+	/* Clear out (for the most part) the other registers */
+	init_registers(regs);
 
-static struct phy_info phy_info_VSC8244 = {
-	0x3f1b,
-	"Vitesse VSC8244",
-	6,
-	(struct phy_cmd[]) {	/* config */
-		/* Override PHY config settings */
-		/* Configure some basic stuff */
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Read the Status (2x to make sure link is right) */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_VSC8244_AUX_CONSTAT, miim_read, &mii_parse_vsc8244},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+	/* Ready the device for tx/rx */
+	startup_tsec(dev);
 
-static struct phy_info phy_info_VSC8641 = {
-	0x7043,
-	"Vitesse VSC8641",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		/* Configure some basic stuff */
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Read the Status (2x to make sure link is right) */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_VSC8244_AUX_CONSTAT, miim_read, &mii_parse_vsc8244},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+	/* Start up the PHY */
+	phy_startup(priv->phydev);
 
-static struct phy_info phy_info_VSC8221 = {
-	0xfc55,
-	"Vitesse VSC8221",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		/* Configure some basic stuff */
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Read the Status (2x to make sure link is right) */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_VSC8244_AUX_CONSTAT, miim_read, &mii_parse_vsc8244},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+	adjust_link(priv, priv->phydev);
 
-static struct phy_info phy_info_VSC8601 = {
-	0x00007042,
-	"Vitesse VSC8601",
-	4,
-	(struct phy_cmd[]) {     /* config */
-		/* Override PHY config settings */
-		/* Configure some basic stuff */
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-#ifdef CONFIG_SYS_VSC8601_SKEWFIX
-		{MIIM_VSC8601_EPHY_CON,MIIM_VSC8601_EPHY_CON_INIT_SKEW,NULL},
-#if defined(CONFIG_SYS_VSC8601_SKEW_TX) && defined(CONFIG_SYS_VSC8601_SKEW_RX)
-		{MIIM_EXT_PAGE_ACCESS,1,NULL},
-#define VSC8101_SKEW \
-	(CONFIG_SYS_VSC8601_SKEW_TX << 14) | (CONFIG_SYS_VSC8601_SKEW_RX << 12)
-		{MIIM_VSC8601_SKEW_CTRL,VSC8101_SKEW,NULL},
-		{MIIM_EXT_PAGE_ACCESS,0,NULL},
-#endif
-#endif
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_RESTART, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {     /* startup */
-		/* Read the Status (2x to make sure link is right) */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_VSC8244_AUX_CONSTAT, miim_read, &mii_parse_vsc8244},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {     /* shutdown */
-		{miim_end,}
-	},
-};
+	/* If there's no link, fail */
+	return priv->phydev->link ? 0 : -1;
+}
 
-static struct phy_info phy_info_dm9161 = {
-	0x0181b88,
-	"Davicom DM9161E",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		{MIIM_CONTROL, MIIM_DM9161_CR_STOP, NULL},
-		/* Do not bypass the scrambler/descrambler */
-		{MIIM_DM9161_SCR, MIIM_DM9161_SCR_INIT, NULL},
-		/* Clear 10BTCSR to default */
-		{MIIM_DM9161_10BTCSR, MIIM_DM9161_10BTCSR_INIT, NULL},
-		/* Configure some basic stuff */
-		{MIIM_CONTROL, MIIM_CR_INIT, NULL},
-		/* Restart Auto Negotiation */
-		{MIIM_CONTROL, MIIM_DM9161_CR_RSTAN, NULL},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_DM9161_SCSR, miim_read, &mii_parse_dm9161_scsr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+static phy_interface_t tsec_get_interface(struct tsec_private *priv)
+{
+	tsec_t *regs = priv->regs;
+	u32 ecntrl;
 
-/* micrel KSZ804  */
-static struct phy_info phy_info_ksz804 =  {
-	0x0022151,
-	"Micrel KSZ804 PHY",
-	4,
-	(struct phy_cmd[]) { /* config */
-		{MII_BMCR, BMCR_RESET, NULL},
-		{MII_BMCR, BMCR_ANENABLE|BMCR_ANRESTART, NULL},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* startup */
-		{MII_BMSR, miim_read, NULL},
-		{MII_BMSR, miim_read, &mii_parse_sr},
-		{MII_BMSR, miim_read, &mii_parse_link},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* shutdown */
-		{miim_end,}
-	}
-};
+	ecntrl = in_be32(&regs->ecntrl);
+
+	if (ecntrl & ECNTRL_SGMII_MODE)
+		return PHY_INTERFACE_MODE_SGMII;
 
-/* a generic flavor.  */
-static struct phy_info phy_info_generic =  {
-	0,
-	"Unknown/Generic PHY",
-	32,
-	(struct phy_cmd[]) { /* config */
-		{MII_BMCR, BMCR_RESET, NULL},
-		{MII_BMCR, BMCR_ANENABLE|BMCR_ANRESTART, NULL},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* startup */
-		{MII_BMSR, miim_read, NULL},
-		{MII_BMSR, miim_read, &mii_parse_sr},
-		{MII_BMSR, miim_read, &mii_parse_link},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) { /* shutdown */
-		{miim_end,}
+	if (ecntrl & ECNTRL_TBI_MODE) {
+		if (ecntrl & ECNTRL_REDUCED_MODE)
+			return PHY_INTERFACE_MODE_RTBI;
+		else
+			return PHY_INTERFACE_MODE_TBI;
 	}
-};
 
-static uint mii_parse_lxt971_sr2(uint mii_reg, struct tsec_private *priv)
-{
-	unsigned int speed;
-	if (priv->link) {
-		speed = mii_reg & MIIM_LXT971_SR2_SPEED_MASK;
-
-		switch (speed) {
-		case MIIM_LXT971_SR2_10HDX:
-			priv->speed = 10;
-			priv->duplexity = 0;
-			break;
-		case MIIM_LXT971_SR2_10FDX:
-			priv->speed = 10;
-			priv->duplexity = 1;
-			break;
-		case MIIM_LXT971_SR2_100HDX:
-			priv->speed = 100;
-			priv->duplexity = 0;
-			break;
-		default:
-			priv->speed = 100;
-			priv->duplexity = 1;
+	if (ecntrl & ECNTRL_REDUCED_MODE) {
+		if (ecntrl & ECNTRL_REDUCED_MII_MODE)
+			return PHY_INTERFACE_MODE_RMII;
+		else {
+			phy_interface_t interface = priv->interface;
+
+			/*
+			 * This isn't autodetected, so it must
+			 * be set by the platform code.
+			 */
+			if ((interface == PHY_INTERFACE_MODE_RGMII_ID) ||
+				 (interface == PHY_INTERFACE_MODE_RGMII_TXID) ||
+				 (interface == PHY_INTERFACE_MODE_RGMII_RXID))
+				return interface;
+
+			return PHY_INTERFACE_MODE_RGMII;
 		}
-	} else {
-		priv->speed = 0;
-		priv->duplexity = 0;
 	}
 
-	return 0;
+	if (priv->flags & TSEC_GIGABIT)
+		return PHY_INTERFACE_MODE_GMII;
+
+	return PHY_INTERFACE_MODE_MII;
 }
 
-static struct phy_info phy_info_lxt971 = {
-	0x0001378e,
-	"LXT971",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		{MIIM_CR, MIIM_CR_INIT, mii_cr_init},	/* autonegotiate */
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup - enable interrupts */
-		/* { 0x12, 0x00f2, NULL }, */
-		{MIIM_STATUS, miim_read, NULL},
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		{MIIM_LXT971_SR2, miim_read, &mii_parse_lxt971_sr2},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown - disable interrupts */
-		{miim_end,}
-	},
-};
 
-/* Parse the DP83865's link and auto-neg status register for speed and duplex
- * information
+/* Discover which PHY is attached to the device, and configure it
+ * properly.  If the PHY is not recognized, then return 0
+ * (failure).  Otherwise, return 1
  */
-static uint mii_parse_dp83865_lanr(uint mii_reg, struct tsec_private *priv)
+static int init_phy(struct eth_device *dev)
 {
-	switch (mii_reg & MIIM_DP83865_SPD_MASK) {
-
-	case MIIM_DP83865_SPD_1000:
-		priv->speed = 1000;
-		break;
-
-	case MIIM_DP83865_SPD_100:
-		priv->speed = 100;
-		break;
-
-	default:
-		priv->speed = 10;
-		break;
+	struct tsec_private *priv = (struct tsec_private *)dev->priv;
+	struct phy_device *phydev;
+	tsec_t *regs = priv->regs;
+	u32 supported = (SUPPORTED_10baseT_Half |
+			SUPPORTED_10baseT_Full |
+			SUPPORTED_100baseT_Half |
+			SUPPORTED_100baseT_Full);
 
-	}
+	if (priv->flags & TSEC_GIGABIT)
+		supported |= SUPPORTED_1000baseT_Full;
 
-	if (mii_reg & MIIM_DP83865_DPX_FULL)
-		priv->duplexity = 1;
-	else
-		priv->duplexity = 0;
+	/* Assign a Physical address to the TBI */
+	out_be32(&regs->tbipa, CONFIG_SYS_TBIPA_VALUE);
 
-	return 0;
-}
+	priv->interface = tsec_get_interface(priv);
 
-static struct phy_info phy_info_dp83865 = {
-	0x20005c7,
-	"NatSemi DP83865",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		{MIIM_CONTROL, MIIM_DP83865_CR_INIT, NULL},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the link and auto-neg status */
-		{MIIM_DP83865_LANR, miim_read, &mii_parse_dp83865_lanr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+	if (priv->interface == PHY_INTERFACE_MODE_SGMII)
+		tsec_configure_serdes(priv);
 
-static struct phy_info phy_info_rtl8211b = {
-	0x001cc91,
-	"RealTek RTL8211B",
-	4,
-	(struct phy_cmd[]) {	/* config */
-		/* Reset and configure the PHY */
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL},
-		{MIIM_ANAR, MIIM_ANAR_INIT, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
-		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* startup */
-		/* Status is read once to clear old link state */
-		{MIIM_STATUS, miim_read, NULL},
-		/* Auto-negotiate */
-		{MIIM_STATUS, miim_read, &mii_parse_sr},
-		/* Read the status */
-		{MIIM_RTL8211B_PHY_STATUS, miim_read, &mii_parse_RTL8211B_sr},
-		{miim_end,}
-	},
-	(struct phy_cmd[]) {	/* shutdown */
-		{miim_end,}
-	},
-};
+	phydev = phy_connect(priv->bus, priv->phyaddr, dev, priv->interface);
 
-struct phy_info phy_info_AR8021 =  {
-        0x4dd04,
-        "AR8021",
-        4,
-        (struct phy_cmd[]) { /* config */
-                {MII_BMCR, BMCR_RESET, NULL},
-                {MII_BMCR, BMCR_ANENABLE|BMCR_ANRESTART, NULL},
-                {0x1d, 0x05, NULL},
-                {0x1e, 0x3D47, NULL},
-                {miim_end,}
-        },
-        (struct phy_cmd[]) { /* startup */
-                {MII_BMSR, miim_read, NULL},
-                {MII_BMSR, miim_read, &mii_parse_sr},
-                {MII_BMSR, miim_read, &mii_parse_link},
-                {miim_end,}
-        },
-        (struct phy_cmd[]) { /* shutdown */
-                {miim_end,}
-        }
-};
+	phydev->supported &= supported;
+	phydev->advertising = phydev->supported;
 
-static struct phy_info *phy_info[] = {
-	&phy_info_cis8204,
-	&phy_info_cis8201,
-	&phy_info_BCM5461S,
-	&phy_info_BCM5464S,
-	&phy_info_BCM5482S,
-	&phy_info_M88E1011S,
-	&phy_info_M88E1111S,
-	&phy_info_M88E1118,
-	&phy_info_M88E1121R,
-	&phy_info_M88E1145,
-	&phy_info_M88E1149S,
-	&phy_info_dm9161,
-	&phy_info_ksz804,
-	&phy_info_lxt971,
-	&phy_info_VSC8211,
-	&phy_info_VSC8244,
-	&phy_info_VSC8601,
-	&phy_info_VSC8641,
-	&phy_info_VSC8221,
-	&phy_info_dp83865,
-	&phy_info_rtl8211b,
-	&phy_info_AR8021,
-	&phy_info_generic,	/* must be last; has ID 0 and 32 bit mask */
-	NULL
-};
+	priv->phydev = phydev;
 
-/* Grab the identifier of the device's PHY, and search through
- * all of the known PHYs to see if one matches.	 If so, return
- * it, if not, return NULL
- */
-static struct phy_info *get_phy_info(struct eth_device *dev)
-{
-	struct tsec_private *priv = (struct tsec_private *)dev->priv;
-	uint phy_reg, phy_ID;
-	int i;
-	struct phy_info *theInfo = NULL;
-
-	/* Grab the bits from PHYIR1, and put them in the upper half */
-	phy_reg = read_phy_reg(priv, MIIM_PHYIR1);
-	phy_ID = (phy_reg & 0xffff) << 16;
-
-	/* Grab the bits from PHYIR2, and put them in the lower half */
-	phy_reg = read_phy_reg(priv, MIIM_PHYIR2);
-	phy_ID |= (phy_reg & 0xffff);
-
-	/* loop through all the known PHY types, and find one that */
-	/* matches the ID we read from the PHY. */
-	for (i = 0; phy_info[i]; i++) {
-		if (phy_info[i]->id == (phy_ID >> phy_info[i]->shift)) {
-			theInfo = phy_info[i];
-			break;
-		}
-	}
+	phy_config(phydev);
 
-	if (theInfo == &phy_info_generic) {
-		printf("%s: No support for PHY id %x; assuming generic\n",
-			dev->name, phy_ID);
-	} else {
-		debug("%s: PHY is %s (%x)\n", dev->name, theInfo->name, phy_ID);
-	}
-
-	return theInfo;
+	return 1;
 }
 
-/* Execute the given series of commands on the given device's
- * PHY, running functions as necessary
+/* Initialize device structure. Returns success if PHY
+ * initialization succeeded (i.e. if it recognizes the PHY)
  */
-static void phy_run_commands(struct tsec_private *priv, struct phy_cmd *cmd)
+static int tsec_initialize(bd_t *bis, struct tsec_info_struct *tsec_info)
 {
+	struct eth_device *dev;
 	int i;
-	uint result;
-	volatile tsec_mdio_t *phyregs = priv->phyregs;
-
-	phyregs->miimcfg = MIIMCFG_RESET;
+	struct tsec_private *priv;
 
-	phyregs->miimcfg = MIIMCFG_INIT_VALUE;
+	dev = (struct eth_device *)malloc(sizeof *dev);
 
-	while (phyregs->miimind & MIIMIND_BUSY) ;
+	if (NULL == dev)
+		return 0;
 
-	for (i = 0; cmd->mii_reg != miim_end; i++) {
-		if (cmd->mii_data == miim_read) {
-			result = read_phy_reg(priv, cmd->mii_reg);
+	memset(dev, 0, sizeof *dev);
 
-			if (cmd->funct != NULL)
-				(*(cmd->funct)) (result, priv);
+	priv = (struct tsec_private *)malloc(sizeof(*priv));
 
-		} else {
-			if (cmd->funct != NULL)
-				result = (*(cmd->funct)) (cmd->mii_reg, priv);
-			else
-				result = cmd->mii_data;
+	if (NULL == priv)
+		return 0;
 
-			write_phy_reg(priv, cmd->mii_reg, result);
+	privlist[num_tsecs++] = priv;
+	priv->regs = tsec_info->regs;
+	priv->phyregs_sgmii = tsec_info->miiregs_sgmii;
 
-		}
-		cmd++;
-	}
-}
+	priv->phyaddr = tsec_info->phyaddr;
+	priv->flags = tsec_info->flags;
 
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) \
-	&& !defined(BITBANGMII)
+	sprintf(dev->name, tsec_info->devname);
+	priv->interface = tsec_info->interface;
+	priv->bus = miiphy_get_dev_by_name(tsec_info->mii_devname);
+	dev->iobase = 0;
+	dev->priv = priv;
+	dev->init = tsec_init;
+	dev->halt = tsec_halt;
+	dev->send = tsec_send;
+	dev->recv = tsec_recv;
+#ifdef CONFIG_MCAST_TFTP
+	dev->mcast = tsec_mcast_addr;
+#endif
 
-/*
- * Read a MII PHY register.
- *
- * Returns:
- *  0 on success
- */
-static int tsec_miiphy_read(const char *devname, unsigned char addr,
-			    unsigned char reg, unsigned short *value)
-{
-	unsigned short ret;
-	struct tsec_private *priv = privlist[0];
+	/* Tell u-boot to get the addr from the env */
+	for (i = 0; i < 6; i++)
+		dev->enetaddr[i] = 0;
 
-	if (NULL == priv) {
-		printf("Can't read PHY at address %d\n", addr);
-		return -1;
-	}
+	eth_register(dev);
 
-	ret = (unsigned short)tsec_local_mdio_read(priv->phyregs, addr, reg);
-	*value = ret;
+	/* Reset the MAC */
+	setbits_be32(&priv->regs->maccfg1, MACCFG1_SOFT_RESET);
+	udelay(2);  /* Soft Reset must be asserted for 3 TX clocks */
+	clrbits_be32(&priv->regs->maccfg1, MACCFG1_SOFT_RESET);
 
-	return 0;
+	/* Try to initialize PHY here, and return */
+	return init_phy(dev);
 }
 
 /*
- * Write a MII PHY register.
+ * Initialize all the TSEC devices
  *
- * Returns:
- *  0 on success
+ * Returns the number of TSEC devices that were initialized
  */
-static int tsec_miiphy_write(const char *devname, unsigned char addr,
-			     unsigned char reg, unsigned short value)
+int tsec_eth_init(bd_t *bis, struct tsec_info_struct *tsecs, int num)
 {
-	struct tsec_private *priv = privlist[0];
+	int i;
+	int ret, count = 0;
 
-	if (NULL == priv) {
-		printf("Can't write PHY at address %d\n", addr);
-		return -1;
+	for (i = 0; i < num; i++) {
+		ret = tsec_initialize(bis, &tsecs[i]);
+		if (ret > 0)
+			count += ret;
 	}
 
-	tsec_local_mdio_write(priv->phyregs, addr, reg, value);
-
-	return 0;
+	return count;
 }
 
-#endif
-
-#ifdef CONFIG_MCAST_TFTP
-
-/* CREDITS: linux gianfar driver, slightly adjusted... thanx. */
-
-/* Set the appropriate hash bit for the given addr */
-
-/* The algorithm works like so:
- * 1) Take the Destination Address (ie the multicast address), and
- * do a CRC on it (little endian), and reverse the bits of the
- * result.
- * 2) Use the 8 most significant bits as a hash into a 256-entry
- * table.  The table is controlled through 8 32-bit registers:
- * gaddr0-7.  gaddr0's MSB is entry 0, and gaddr7's LSB is
- * gaddr7.  This means that the 3 most significant bits in the
- * hash index which gaddr register to use, and the 5 other bits
- * indicate which bit (assuming an IBM numbering scheme, which
- * for PowerPC (tm) is usually the case) in the tregister holds
- * the entry. */
-static int
-tsec_mcast_addr (struct eth_device *dev, u8 mcast_mac, u8 set)
+int tsec_standard_init(bd_t *bis)
 {
-	struct tsec_private *priv = privlist[1];
-	volatile tsec_t *regs = priv->regs;
-	volatile u32  *reg_array, value;
-	u8 result, whichbit, whichreg;
+	struct fsl_pq_mdio_info info;
 
-	result = (u8)((ether_crc(MAC_ADDR_LEN,mcast_mac) >> 24) & 0xff);
-	whichbit = result & 0x1f;	/* the 5 LSB = which bit to set */
-	whichreg = result >> 5;		/* the 3 MSB = which reg to set it in */
-	value = (1 << (31-whichbit));
+	info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+	info.name = DEFAULT_MII_NAME;
 
-	reg_array = &(regs->hash.gaddr0);
+	fsl_pq_mdio_init(bis, &info);
 
-	if (set) {
-		reg_array[whichreg] |= value;
-	} else {
-		reg_array[whichreg] &= ~value;
-	}
-	return 0;
+	return tsec_eth_init(bis, tsec_info, ARRAY_SIZE(tsec_info));
 }
-#endif /* Multicast TFTP ? */
+
diff --git a/drivers/net/uli526x.c b/drivers/net/uli526x.c
index a4624e1734..5933bddce5 100644
--- a/drivers/net/uli526x.c
+++ b/drivers/net/uli526x.c
@@ -175,9 +175,9 @@ static u16 read_srom_word(long, int);
 static void uli526x_descriptor_init(struct uli526x_board_info *, unsigned long);
 static void allocate_rx_buffer(struct uli526x_board_info *);
 static void update_cr6(u32, unsigned long);
-static u16 phy_read(unsigned long, u8, u8, u32);
+static u16 uli_phy_read(unsigned long, u8, u8, u32);
 static u16 phy_readby_cr10(unsigned long, u8, u8);
-static void phy_write(unsigned long, u8, u8, u16, u32);
+static void uli_phy_write(unsigned long, u8, u8, u16, u32);
 static void phy_writeby_cr10(unsigned long, u8, u8, u16);
 static void phy_write_1bit(unsigned long, u32, u32);
 static u16 phy_read_1bit(unsigned long, u32);
@@ -349,7 +349,7 @@ static void uli526x_disable(struct eth_device *dev)
 		/* Reset & stop ULI526X board */
 		outl(ULI526X_RESET, db->ioaddr + DCR0);
 		udelay(5);
-		phy_write(db->ioaddr, db->phy_addr, 0, 0x8000, db->chip_id);
+		uli_phy_write(db->ioaddr, db->phy_addr, 0, 0x8000, db->chip_id);
 
 		/* reset the board */
 		db->cr6_data &= ~(CR6_RXSC | CR6_TXSC);	/* Disable Tx/Rx */
@@ -385,7 +385,7 @@ static void uli526x_init(struct eth_device *dev)
 	db->tx_packet_cnt = 0;
 	for (phy_tmp = 0; phy_tmp < 32; phy_tmp++) {
 		/* peer add */
-		phy_value = phy_read(db->ioaddr, phy_tmp, 3, db->chip_id);
+		phy_value = uli_phy_read(db->ioaddr, phy_tmp, 3, db->chip_id);
 		if (phy_value != 0xffff && phy_value != 0) {
 			db->phy_addr = phy_tmp;
 			break;
@@ -404,10 +404,10 @@ static void uli526x_init(struct eth_device *dev)
 
 	if (!(inl(db->ioaddr + DCR12) & 0x8)) {
 		/* Phyxcer capability setting */
-		phy_reg_reset = phy_read(db->ioaddr,
+		phy_reg_reset = uli_phy_read(db->ioaddr,
 			db->phy_addr, 0, db->chip_id);
 		phy_reg_reset = (phy_reg_reset | 0x8000);
-		phy_write(db->ioaddr, db->phy_addr, 0,
+		uli_phy_write(db->ioaddr, db->phy_addr, 0,
 			phy_reg_reset, db->chip_id);
 		udelay(500);
 
@@ -781,7 +781,8 @@ static void uli526x_set_phyxcer(struct uli526x_board_info *db)
 	u16 phy_reg;
 
 	/* Phyxcer capability setting */
-	phy_reg = phy_read(db->ioaddr, db->phy_addr, 4, db->chip_id) & ~0x01e0;
+	phy_reg = uli_phy_read(db->ioaddr,
+			db->phy_addr, 4, db->chip_id) & ~0x01e0;
 
 	if (db->media_mode & ULI526X_AUTO) {
 		/* AUTO Mode */
@@ -802,10 +803,10 @@ static void uli526x_set_phyxcer(struct uli526x_board_info *db)
 		phy_reg |= db->PHY_reg4;
 		db->media_mode |= ULI526X_AUTO;
 	}
-	phy_write(db->ioaddr, db->phy_addr, 4, phy_reg, db->chip_id);
+	uli_phy_write(db->ioaddr, db->phy_addr, 4, phy_reg, db->chip_id);
 
 	/* Restart Auto-Negotiation */
-	phy_write(db->ioaddr, db->phy_addr, 0, 0x1200, db->chip_id);
+	uli_phy_write(db->ioaddr, db->phy_addr, 0, 0x1200, db->chip_id);
 	udelay(50);
 }
 
@@ -813,7 +814,7 @@ static void uli526x_set_phyxcer(struct uli526x_board_info *db)
  *	Write a word to Phy register
  */
 
-static void phy_write(unsigned long iobase, u8 phy_addr, u8 offset,
+static void uli_phy_write(unsigned long iobase, u8 phy_addr, u8 offset,
 	u16 phy_data, u32 chip_id)
 {
 	u16 i;
@@ -862,7 +863,8 @@ static void phy_write(unsigned long iobase, u8 phy_addr, u8 offset,
  *	Read a word data from phy register
  */
 
-static u16 phy_read(unsigned long iobase, u8 phy_addr, u8 offset, u32 chip_id)
+static u16 uli_phy_read(unsigned long iobase, u8 phy_addr, u8 offset,
+			u32 chip_id)
 {
 	int i;
 	u16 phy_data;
diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c
index 811e3fc315..1ecb1379a5 100644
--- a/drivers/qe/uec.c
+++ b/drivers/qe/uec.c
@@ -30,6 +30,7 @@
 #include "uec.h"
 #include "uec_phy.h"
 #include "miiphy.h"
+#include <phy.h>
 
 /* Default UTBIPAR SMI address */
 #ifndef CONFIG_UTBIPAR_INIT_TBIPA
@@ -67,9 +68,6 @@ static uec_info_t uec_info[] = {
 
 static struct eth_device *devlist[MAXCONTROLLERS];
 
-u16 phy_read (struct uec_mii_info *mii_info, u16 regnum);
-void phy_write (struct uec_mii_info *mii_info, u16 regnum, u16 val);
-
 static int uec_mac_enable(uec_private_t *uec, comm_dir_e mode)
 {
 	uec_t		*uec_regs;
@@ -324,9 +322,9 @@ static int uec_set_mac_duplex(uec_private_t *uec, int duplex)
 }
 
 static int uec_set_mac_if_mode(uec_private_t *uec,
-		enum fsl_phy_enet_if if_mode, int speed)
+		phy_interface_t if_mode, int speed)
 {
-	enum fsl_phy_enet_if	enet_if_mode;
+	phy_interface_t		enet_if_mode;
 	uec_info_t		*uec_info;
 	uec_t			*uec_regs;
 	u32			upsmr;
@@ -348,15 +346,15 @@ static int uec_set_mac_if_mode(uec_private_t *uec,
 	upsmr &= ~(UPSMR_RPM | UPSMR_TBIM | UPSMR_R10M | UPSMR_RMM);
 
 	switch (speed) {
-		case 10:
+		case SPEED_10:
 			maccfg2 |= MACCFG2_INTERFACE_MODE_NIBBLE;
 			switch (enet_if_mode) {
-				case MII:
+				case PHY_INTERFACE_MODE_MII:
 					break;
-				case RGMII:
+				case PHY_INTERFACE_MODE_RGMII:
 					upsmr |= (UPSMR_RPM | UPSMR_R10M);
 					break;
-				case RMII:
+				case PHY_INTERFACE_MODE_RMII:
 					upsmr |= (UPSMR_R10M | UPSMR_RMM);
 					break;
 				default:
@@ -364,15 +362,15 @@ static int uec_set_mac_if_mode(uec_private_t *uec,
 					break;
 			}
 			break;
-		case 100:
+		case SPEED_100:
 			maccfg2 |= MACCFG2_INTERFACE_MODE_NIBBLE;
 			switch (enet_if_mode) {
-				case MII:
+				case PHY_INTERFACE_MODE_MII:
 					break;
-				case RGMII:
+				case PHY_INTERFACE_MODE_RGMII:
 					upsmr |= UPSMR_RPM;
 					break;
-				case RMII:
+				case PHY_INTERFACE_MODE_RMII:
 					upsmr |= UPSMR_RMM;
 					break;
 				default:
@@ -380,23 +378,24 @@ static int uec_set_mac_if_mode(uec_private_t *uec,
 					break;
 			}
 			break;
-		case 1000:
+		case SPEED_1000:
 			maccfg2 |= MACCFG2_INTERFACE_MODE_BYTE;
 			switch (enet_if_mode) {
-				case GMII:
+				case PHY_INTERFACE_MODE_GMII:
 					break;
-				case TBI:
+				case PHY_INTERFACE_MODE_TBI:
 					upsmr |= UPSMR_TBIM;
 					break;
-				case RTBI:
+				case PHY_INTERFACE_MODE_RTBI:
 					upsmr |= (UPSMR_RPM | UPSMR_TBIM);
 					break;
-				case RGMII_RXID:
-				case RGMII_ID:
-				case RGMII:
+				case PHY_INTERFACE_MODE_RGMII_RXID:
+				case PHY_INTERFACE_MODE_RGMII_TXID:
+				case PHY_INTERFACE_MODE_RGMII_ID:
+				case PHY_INTERFACE_MODE_RGMII:
 					upsmr |= UPSMR_RPM;
 					break;
-				case SGMII:
+				case PHY_INTERFACE_MODE_SGMII:
 					upsmr |= UPSMR_SGMM;
 					break;
 				default:
@@ -521,7 +520,7 @@ static void adjust_link(struct eth_device *dev)
 	struct uec_mii_info	*mii_info = uec->mii_info;
 
 	extern void change_phy_interface_mode(struct eth_device *dev,
-				 enum fsl_phy_enet_if mode, int speed);
+				 phy_interface_t mode, int speed);
 	uec_regs = uec->uec_regs;
 
 	if (mii_info->link) {
@@ -539,19 +538,19 @@ static void adjust_link(struct eth_device *dev)
 		}
 
 		if (mii_info->speed != uec->oldspeed) {
-			enum fsl_phy_enet_if	mode = \
+			phy_interface_t mode =
 				uec->uec_info->enet_interface_type;
 			if (uec->uec_info->uf_info.eth_type == GIGA_ETH) {
 				switch (mii_info->speed) {
-				case 1000:
+				case SPEED_1000:
 					break;
-				case 100:
+				case SPEED_100:
 					printf ("switching to rgmii 100\n");
-					mode = RGMII;
+					mode = PHY_INTERFACE_MODE_RGMII;
 					break;
-				case 10:
+				case SPEED_10:
 					printf ("switching to rgmii 10\n");
-					mode = RGMII;
+					mode = PHY_INTERFACE_MODE_RGMII;
 					break;
 				default:
 					printf("%s: Ack,Speed(%d)is illegal\n",
@@ -1115,8 +1114,8 @@ static int uec_startup(uec_private_t *uec)
 	out_be32(&uec_regs->utbipar, utbipar);
 
 	/* Configure the TBI for SGMII operation */
-	if ((uec->uec_info->enet_interface_type == SGMII) &&
-	   (uec->uec_info->speed == 1000)) {
+	if ((uec->uec_info->enet_interface_type == PHY_INTERFACE_MODE_SGMII) &&
+	   (uec->uec_info->speed == SPEED_1000)) {
 		uec_write_phy_reg(uec->dev, uec_regs->utbipar,
 			ENET_TBI_MII_ANA, TBIANA_SETTINGS);
 
diff --git a/drivers/qe/uec.h b/drivers/qe/uec.h
index 94eb9a26d7..e63bf3a652 100644
--- a/drivers/qe/uec.h
+++ b/drivers/qe/uec.h
@@ -25,6 +25,7 @@
 
 #include "qe.h"
 #include "uccf.h"
+#include <phy.h>
 #include <asm/fsl_enet.h>
 
 #define MAX_TX_THREADS				8
@@ -691,7 +692,7 @@ typedef struct uec_info {
 	u16				rx_bd_ring_len;
 	u16				tx_bd_ring_len;
 	u8				phy_address;
-	enum fsl_phy_enet_if		enet_interface_type;
+	phy_interface_t			enet_interface_type;
 	int				speed;
 } uec_info_t;
 
diff --git a/drivers/qe/uec_phy.c b/drivers/qe/uec_phy.c
index 55c2622942..e26218be88 100644
--- a/drivers/qe/uec_phy.c
+++ b/drivers/qe/uec_phy.c
@@ -25,6 +25,7 @@
 #include "uec.h"
 #include "uec_phy.h"
 #include "miiphy.h"
+#include <phy.h>
 
 #define ugphy_printk(format, arg...)  \
 	printf(format "\n", ## arg)
@@ -121,8 +122,8 @@ static int gbit_config_aneg (struct uec_mii_info *mii_info);
 static int genmii_config_aneg (struct uec_mii_info *mii_info);
 static int genmii_update_link (struct uec_mii_info *mii_info);
 static int genmii_read_status (struct uec_mii_info *mii_info);
-u16 phy_read (struct uec_mii_info *mii_info, u16 regnum);
-void phy_write (struct uec_mii_info *mii_info, u16 regnum, u16 val);
+u16 uec_phy_read(struct uec_mii_info *mii_info, u16 regnum);
+void uec_phy_write(struct uec_mii_info *mii_info, u16 regnum, u16 val);
 
 /* Write value to the PHY for this device to the register at regnum, */
 /* waiting until the write is done before it returns.  All PHY */
@@ -242,7 +243,7 @@ static void config_genmii_advert (struct uec_mii_info *mii_info)
 	advertise = mii_info->advertising;
 
 	/* Setup standard advertisement */
-	adv = phy_read (mii_info, MII_ADVERTISE);
+	adv = uec_phy_read(mii_info, MII_ADVERTISE);
 	adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 	if (advertise & ADVERTISED_10baseT_Half)
 		adv |= ADVERTISE_10HALF;
@@ -252,7 +253,7 @@ static void config_genmii_advert (struct uec_mii_info *mii_info)
 		adv |= ADVERTISE_100HALF;
 	if (advertise & ADVERTISED_100baseT_Full)
 		adv |= ADVERTISE_100FULL;
-	phy_write (mii_info, MII_ADVERTISE, adv);
+	uec_phy_write(mii_info, MII_ADVERTISE, adv);
 }
 
 static void genmii_setup_forced (struct uec_mii_info *mii_info)
@@ -260,7 +261,7 @@ static void genmii_setup_forced (struct uec_mii_info *mii_info)
 	u16 ctrl;
 	u32 features = mii_info->phyinfo->features;
 
-	ctrl = phy_read (mii_info, MII_BMCR);
+	ctrl = uec_phy_read(mii_info, MII_BMCR);
 
 	ctrl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 |
 		  BMCR_SPEED1000 | BMCR_ANENABLE);
@@ -290,7 +291,7 @@ static void genmii_setup_forced (struct uec_mii_info *mii_info)
 		break;
 	}
 
-	phy_write (mii_info, MII_BMCR, ctrl);
+	uec_phy_write(mii_info, MII_BMCR, ctrl);
 }
 
 /* Enable and Restart Autonegotiation */
@@ -298,9 +299,9 @@ static void genmii_restart_aneg (struct uec_mii_info *mii_info)
 {
 	u16 ctl;
 
-	ctl = phy_read (mii_info, MII_BMCR);
+	ctl = uec_phy_read(mii_info, MII_BMCR);
 	ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
-	phy_write (mii_info, MII_BMCR, ctl);
+	uec_phy_write(mii_info, MII_BMCR, ctl);
 }
 
 static int gbit_config_aneg (struct uec_mii_info *mii_info)
@@ -313,14 +314,14 @@ static int gbit_config_aneg (struct uec_mii_info *mii_info)
 		config_genmii_advert (mii_info);
 		advertise = mii_info->advertising;
 
-		adv = phy_read (mii_info, MII_CTRL1000);
+		adv = uec_phy_read(mii_info, MII_CTRL1000);
 		adv &= ~(ADVERTISE_1000FULL |
 			 ADVERTISE_1000HALF);
 		if (advertise & SUPPORTED_1000baseT_Half)
 			adv |= ADVERTISE_1000HALF;
 		if (advertise & SUPPORTED_1000baseT_Full)
 			adv |= ADVERTISE_1000FULL;
-		phy_write (mii_info, MII_CTRL1000, adv);
+		uec_phy_write(mii_info, MII_CTRL1000, adv);
 
 		/* Start/Restart aneg */
 		genmii_restart_aneg (mii_info);
@@ -335,13 +336,13 @@ static int marvell_config_aneg (struct uec_mii_info *mii_info)
 	/* The Marvell PHY has an errata which requires
 	 * that certain registers get written in order
 	 * to restart autonegotiation */
-	phy_write (mii_info, MII_BMCR, BMCR_RESET);
+	uec_phy_write(mii_info, MII_BMCR, BMCR_RESET);
 
-	phy_write (mii_info, 0x1d, 0x1f);
-	phy_write (mii_info, 0x1e, 0x200c);
-	phy_write (mii_info, 0x1d, 0x5);
-	phy_write (mii_info, 0x1e, 0);
-	phy_write (mii_info, 0x1e, 0x100);
+	uec_phy_write(mii_info, 0x1d, 0x1f);
+	uec_phy_write(mii_info, 0x1e, 0x200c);
+	uec_phy_write(mii_info, 0x1d, 0x5);
+	uec_phy_write(mii_info, 0x1e, 0);
+	uec_phy_write(mii_info, 0x1e, 0x100);
 
 	gbit_config_aneg (mii_info);
 
@@ -373,13 +374,13 @@ static int genmii_update_link (struct uec_mii_info *mii_info)
 	u16 status;
 
 	/* Status is read once to clear old link state */
-	phy_read (mii_info, MII_BMSR);
+	uec_phy_read(mii_info, MII_BMSR);
 
 	/*
 	 * Wait if the link is up, and autonegotiation is in progress
 	 * (ie - we're capable and it's not done)
 	 */
-	status = phy_read(mii_info, MII_BMSR);
+	status = uec_phy_read(mii_info, MII_BMSR);
 	if ((status & BMSR_LSTATUS) && (status & BMSR_ANEGCAPABLE)
 	    && !(status & BMSR_ANEGCOMPLETE)) {
 		int i = 0;
@@ -395,7 +396,7 @@ static int genmii_update_link (struct uec_mii_info *mii_info)
 
 			i++;
 			udelay(1000);	/* 1 ms */
-			status = phy_read(mii_info, MII_BMSR);
+			status = uec_phy_read(mii_info, MII_BMSR);
 		}
 		mii_info->link = 1;
 	} else {
@@ -420,7 +421,7 @@ static int genmii_read_status (struct uec_mii_info *mii_info)
 		return err;
 
 	if (mii_info->autoneg) {
-		status = phy_read(mii_info, MII_STAT1000);
+		status = uec_phy_read(mii_info, MII_STAT1000);
 
 		if (status & (LPA_1000FULL | LPA_1000HALF)) {
 			mii_info->speed = SPEED_1000;
@@ -429,7 +430,7 @@ static int genmii_read_status (struct uec_mii_info *mii_info)
 			else
 				mii_info->duplex = DUPLEX_HALF;
 		} else {
-			status = phy_read(mii_info, MII_LPA);
+			status = uec_phy_read(mii_info, MII_LPA);
 
 			if (status & (LPA_10FULL | LPA_100FULL))
 				mii_info->duplex = DUPLEX_FULL;
@@ -456,62 +457,63 @@ static int bcm_init(struct uec_mii_info *mii_info)
 
 	gbit_config_aneg(mii_info);
 
-	if ((uec->uec_info->enet_interface_type == RGMII_RXID) &&
-	   (uec->uec_info->speed == 1000)) {
+	if ((uec->uec_info->enet_interface_type ==
+				PHY_INTERFACE_MODE_RGMII_RXID) &&
+			(uec->uec_info->speed == SPEED_1000)) {
 		u16 val;
 		int cnt = 50;
 
 		/* Wait for aneg to complete. */
 		do
-			val = phy_read(mii_info, MII_BMSR);
+			val = uec_phy_read(mii_info, MII_BMSR);
 		while (--cnt && !(val & BMSR_ANEGCOMPLETE));
 
 		/* Set RDX clk delay. */
-		phy_write(mii_info, 0x18, 0x7 | (7 << 12));
+		uec_phy_write(mii_info, 0x18, 0x7 | (7 << 12));
 
-		val = phy_read(mii_info, 0x18);
+		val = uec_phy_read(mii_info, 0x18);
 		/* Set RDX-RXC skew. */
 		val |= (1 << 8);
 		val |= (7 | (7 << 12));
 		/* Write bits 14:0. */
 		val |= (1 << 15);
-		phy_write(mii_info, 0x18, val);
+		uec_phy_write(mii_info, 0x18, val);
 	}
 
 	 return 0;
 }
 
-static int marvell_init(struct uec_mii_info *mii_info)
+static int uec_marvell_init(struct uec_mii_info *mii_info)
 {
 	struct eth_device *edev = mii_info->dev;
 	uec_private_t *uec = edev->priv;
-	enum fsl_phy_enet_if iface = uec->uec_info->enet_interface_type;
+	phy_interface_t iface = uec->uec_info->enet_interface_type;
 	int	speed = uec->uec_info->speed;
 
-	if ((speed == 1000) &&
-	   (iface == RGMII_ID ||
-	    iface == RGMII_RXID ||
-	    iface == RGMII_TXID)) {
+	if ((speed == SPEED_1000) &&
+	   (iface == PHY_INTERFACE_MODE_RGMII_ID ||
+	    iface == PHY_INTERFACE_MODE_RGMII_RXID ||
+	    iface == PHY_INTERFACE_MODE_RGMII_TXID)) {
 		int temp;
 
-		temp = phy_read(mii_info, MII_M1111_PHY_EXT_CR);
-		if (iface == RGMII_ID) {
+		temp = uec_phy_read(mii_info, MII_M1111_PHY_EXT_CR);
+		if (iface == PHY_INTERFACE_MODE_RGMII_ID) {
 			temp |= MII_M1111_RX_DELAY | MII_M1111_TX_DELAY;
-		} else if (iface == RGMII_RXID) {
+		} else if (iface == PHY_INTERFACE_MODE_RGMII_RXID) {
 			temp &= ~MII_M1111_TX_DELAY;
 			temp |= MII_M1111_RX_DELAY;
-		} else if (iface == RGMII_TXID) {
+		} else if (iface == PHY_INTERFACE_MODE_RGMII_TXID) {
 			temp &= ~MII_M1111_RX_DELAY;
 			temp |= MII_M1111_TX_DELAY;
 		}
-		phy_write(mii_info, MII_M1111_PHY_EXT_CR, temp);
+		uec_phy_write(mii_info, MII_M1111_PHY_EXT_CR, temp);
 
-		temp = phy_read(mii_info, MII_M1111_PHY_EXT_SR);
+		temp = uec_phy_read(mii_info, MII_M1111_PHY_EXT_SR);
 		temp &= ~MII_M1111_HWCFG_MODE_MASK;
 		temp |= MII_M1111_HWCFG_MODE_RGMII;
-		phy_write(mii_info, MII_M1111_PHY_EXT_SR, temp);
+		uec_phy_write(mii_info, MII_M1111_PHY_EXT_SR, temp);
 
-		phy_write(mii_info, MII_BMCR, BMCR_RESET);
+		uec_phy_write(mii_info, MII_BMCR, BMCR_RESET);
 	}
 
 	return 0;
@@ -534,7 +536,7 @@ static int marvell_read_status (struct uec_mii_info *mii_info)
 	if (mii_info->autoneg && mii_info->link) {
 		int speed;
 
-		status = phy_read (mii_info, MII_M1011_PHY_SPEC_STATUS);
+		status = uec_phy_read(mii_info, MII_M1011_PHY_SPEC_STATUS);
 
 		/* Get the duplexity */
 		if (status & MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX)
@@ -564,7 +566,7 @@ static int marvell_read_status (struct uec_mii_info *mii_info)
 static int marvell_ack_interrupt (struct uec_mii_info *mii_info)
 {
 	/* Clear the interrupts by reading the reg */
-	phy_read (mii_info, MII_M1011_IEVENT);
+	uec_phy_read(mii_info, MII_M1011_IEVENT);
 
 	return 0;
 }
@@ -572,9 +574,10 @@ static int marvell_ack_interrupt (struct uec_mii_info *mii_info)
 static int marvell_config_intr (struct uec_mii_info *mii_info)
 {
 	if (mii_info->interrupts == MII_INTERRUPT_ENABLED)
-		phy_write (mii_info, MII_M1011_IMASK, MII_M1011_IMASK_INIT);
+		uec_phy_write(mii_info, MII_M1011_IMASK, MII_M1011_IMASK_INIT);
 	else
-		phy_write (mii_info, MII_M1011_IMASK, MII_M1011_IMASK_CLEAR);
+		uec_phy_write(mii_info, MII_M1011_IMASK,
+				MII_M1011_IMASK_CLEAR);
 
 	return 0;
 }
@@ -582,13 +585,13 @@ static int marvell_config_intr (struct uec_mii_info *mii_info)
 static int dm9161_init (struct uec_mii_info *mii_info)
 {
 	/* Reset the PHY */
-	phy_write (mii_info, MII_BMCR, phy_read (mii_info, MII_BMCR) |
+	uec_phy_write(mii_info, MII_BMCR, uec_phy_read(mii_info, MII_BMCR) |
 		   BMCR_RESET);
 	/* PHY and MAC connect */
-	phy_write (mii_info, MII_BMCR, phy_read (mii_info, MII_BMCR) &
+	uec_phy_write(mii_info, MII_BMCR, uec_phy_read(mii_info, MII_BMCR) &
 		   ~BMCR_ISOLATE);
 
-	phy_write (mii_info, MII_DM9161_SCR, MII_DM9161_SCR_INIT);
+	uec_phy_write(mii_info, MII_DM9161_SCR, MII_DM9161_SCR_INIT);
 
 	config_genmii_advert (mii_info);
 	/* Start/restart aneg */
@@ -614,7 +617,7 @@ static int dm9161_read_status (struct uec_mii_info *mii_info)
 	/* If the link is up, read the speed and duplex
 	   If we aren't autonegotiating assume speeds are as set */
 	if (mii_info->autoneg && mii_info->link) {
-		status = phy_read (mii_info, MII_DM9161_SCSR);
+		status = uec_phy_read(mii_info, MII_DM9161_SCSR);
 		if (status & (MII_DM9161_SCSR_100F | MII_DM9161_SCSR_100H))
 			mii_info->speed = SPEED_100;
 		else
@@ -632,7 +635,7 @@ static int dm9161_read_status (struct uec_mii_info *mii_info)
 static int dm9161_ack_interrupt (struct uec_mii_info *mii_info)
 {
 	/* Clear the interrupt by reading the reg */
-	phy_read (mii_info, MII_DM9161_INTR);
+	uec_phy_read(mii_info, MII_DM9161_INTR);
 
 	return 0;
 }
@@ -640,9 +643,9 @@ static int dm9161_ack_interrupt (struct uec_mii_info *mii_info)
 static int dm9161_config_intr (struct uec_mii_info *mii_info)
 {
 	if (mii_info->interrupts == MII_INTERRUPT_ENABLED)
-		phy_write (mii_info, MII_DM9161_INTR, MII_DM9161_INTR_INIT);
+		uec_phy_write(mii_info, MII_DM9161_INTR, MII_DM9161_INTR_INIT);
 	else
-		phy_write (mii_info, MII_DM9161_INTR, MII_DM9161_INTR_STOP);
+		uec_phy_write(mii_info, MII_DM9161_INTR, MII_DM9161_INTR_STOP);
 
 	return 0;
 }
@@ -696,7 +699,7 @@ static int smsc_read_status (struct uec_mii_info *mii_info)
 	if (mii_info->autoneg && mii_info->link) {
 		int	val;
 
-		status = phy_read (mii_info, 0x1f);
+		status = uec_phy_read(mii_info, 0x1f);
 		val = (status & 0x1c) >> 2;
 
 		switch (val) {
@@ -751,7 +754,7 @@ static struct phy_info phy_info_marvell = {
 	.phy_id_mask = 0xffffff00,
 	.name = "Marvell 88E11x1",
 	.features = MII_GBIT_FEATURES,
-	.init = &marvell_init,
+	.init = &uec_marvell_init,
 	.config_aneg = &marvell_config_aneg,
 	.read_status = &marvell_read_status,
 	.ack_interrupt = &marvell_ack_interrupt,
@@ -804,12 +807,12 @@ static struct phy_info *phy_info[] = {
 	NULL
 };
 
-u16 phy_read (struct uec_mii_info *mii_info, u16 regnum)
+u16 uec_phy_read(struct uec_mii_info *mii_info, u16 regnum)
 {
 	return mii_info->mdio_read (mii_info->dev, mii_info->mii_id, regnum);
 }
 
-void phy_write (struct uec_mii_info *mii_info, u16 regnum, u16 val)
+void uec_phy_write(struct uec_mii_info *mii_info, u16 regnum, u16 val)
 {
 	mii_info->mdio_write (mii_info->dev, mii_info->mii_id, regnum, val);
 }
@@ -825,11 +828,11 @@ struct phy_info *uec_get_phy_info (struct uec_mii_info *mii_info)
 	struct phy_info *theInfo = NULL;
 
 	/* Grab the bits from PHYIR1, and put them in the upper half */
-	phy_reg = phy_read (mii_info, MII_PHYSID1);
+	phy_reg = uec_phy_read(mii_info, MII_PHYSID1);
 	phy_ID = (phy_reg & 0xffff) << 16;
 
 	/* Grab the bits from PHYIR2, and put them in the lower half */
-	phy_reg = phy_read (mii_info, MII_PHYSID2);
+	phy_reg = uec_phy_read(mii_info, MII_PHYSID2);
 	phy_ID |= (phy_reg & 0xffff);
 
 	/* loop through all the known PHY types, and find one that */
@@ -852,10 +855,8 @@ struct phy_info *uec_get_phy_info (struct uec_mii_info *mii_info)
 	return theInfo;
 }
 
-void marvell_phy_interface_mode (struct eth_device *dev,
-				 enum fsl_phy_enet_if type,
-				 int speed
-				)
+void marvell_phy_interface_mode(struct eth_device *dev, phy_interface_t type,
+		int speed)
 {
 	uec_private_t *uec = (uec_private_t *) dev->priv;
 	struct uec_mii_info *mii_info;
@@ -867,47 +868,47 @@ void marvell_phy_interface_mode (struct eth_device *dev,
 	}
 	mii_info = uec->mii_info;
 
-	if (type == RGMII) {
-		if (speed == 100) {
-			phy_write (mii_info, 0x00, 0x9140);
-			phy_write (mii_info, 0x1d, 0x001f);
-			phy_write (mii_info, 0x1e, 0x200c);
-			phy_write (mii_info, 0x1d, 0x0005);
-			phy_write (mii_info, 0x1e, 0x0000);
-			phy_write (mii_info, 0x1e, 0x0100);
-			phy_write (mii_info, 0x09, 0x0e00);
-			phy_write (mii_info, 0x04, 0x01e1);
-			phy_write (mii_info, 0x00, 0x9140);
-			phy_write (mii_info, 0x00, 0x1000);
+	if (type == PHY_INTERFACE_MODE_RGMII) {
+		if (speed == SPEED_100) {
+			uec_phy_write(mii_info, 0x00, 0x9140);
+			uec_phy_write(mii_info, 0x1d, 0x001f);
+			uec_phy_write(mii_info, 0x1e, 0x200c);
+			uec_phy_write(mii_info, 0x1d, 0x0005);
+			uec_phy_write(mii_info, 0x1e, 0x0000);
+			uec_phy_write(mii_info, 0x1e, 0x0100);
+			uec_phy_write(mii_info, 0x09, 0x0e00);
+			uec_phy_write(mii_info, 0x04, 0x01e1);
+			uec_phy_write(mii_info, 0x00, 0x9140);
+			uec_phy_write(mii_info, 0x00, 0x1000);
 			udelay (100000);
-			phy_write (mii_info, 0x00, 0x2900);
-			phy_write (mii_info, 0x14, 0x0cd2);
-			phy_write (mii_info, 0x00, 0xa100);
-			phy_write (mii_info, 0x09, 0x0000);
-			phy_write (mii_info, 0x1b, 0x800b);
-			phy_write (mii_info, 0x04, 0x05e1);
-			phy_write (mii_info, 0x00, 0xa100);
-			phy_write (mii_info, 0x00, 0x2100);
+			uec_phy_write(mii_info, 0x00, 0x2900);
+			uec_phy_write(mii_info, 0x14, 0x0cd2);
+			uec_phy_write(mii_info, 0x00, 0xa100);
+			uec_phy_write(mii_info, 0x09, 0x0000);
+			uec_phy_write(mii_info, 0x1b, 0x800b);
+			uec_phy_write(mii_info, 0x04, 0x05e1);
+			uec_phy_write(mii_info, 0x00, 0xa100);
+			uec_phy_write(mii_info, 0x00, 0x2100);
 			udelay (1000000);
-		} else if (speed == 10) {
-			phy_write (mii_info, 0x14, 0x8e40);
-			phy_write (mii_info, 0x1b, 0x800b);
-			phy_write (mii_info, 0x14, 0x0c82);
-			phy_write (mii_info, 0x00, 0x8100);
+		} else if (speed == SPEED_10) {
+			uec_phy_write(mii_info, 0x14, 0x8e40);
+			uec_phy_write(mii_info, 0x1b, 0x800b);
+			uec_phy_write(mii_info, 0x14, 0x0c82);
+			uec_phy_write(mii_info, 0x00, 0x8100);
 			udelay (1000000);
 		}
 	}
 
 	/* handle 88e1111 rev.B2 erratum 5.6 */
 	if (mii_info->autoneg) {
-		status = phy_read (mii_info, MII_BMCR);
-		phy_write (mii_info, MII_BMCR, status | BMCR_ANENABLE);
+		status = uec_phy_read(mii_info, MII_BMCR);
+		uec_phy_write(mii_info, MII_BMCR, status | BMCR_ANENABLE);
 	}
 	/* now the B2 will correctly report autoneg completion status */
 }
 
 void change_phy_interface_mode (struct eth_device *dev,
-				enum fsl_phy_enet_if type, int speed)
+				phy_interface_t type, int speed)
 {
 #ifdef CONFIG_PHY_MODE_NEED_CHANGE
 	marvell_phy_interface_mode (dev, type, speed);