ehci-omap: Clean up added ehci-omap.c

Clean up added ehci-omap.c and make it generic for re-use across
omap-soc having same ehci ip block. Also pass the modes to be configured
from board file and configure the ports accordingly. All usb layers
are not cache aligned, till then keep cache off for usb ops as ehci will use
internally dma for all usb ops.

* Add a generic common header ehci-omap.h having common ip block
  data and reg shifts.
* Rename and modify ehci-omap3 to ehci.h retain only conflicting
  sysc reg shifts remove others and move to common header file.
* pass the board data for beagle/panda accordinly to use
  ehci ports.

Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>

1 files changed, 154 insertions, 55 deletions

diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index 93d3bb7344..00f787fc97 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -27,14 +27,78 @@
  */
 #include <common.h>
 #include <usb.h>
+#include <usb/ulpi.h>
+#include <errno.h>
 #include <asm/io.h>
 #include <asm/gpio.h>
-#include <asm/arch/clocks.h>
-#include <asm/arch/clocks_omap3.h>
-#include <asm/arch/ehci_omap3.h>
-#include <asm/arch/sys_proto.h>
+#include <asm/arch/ehci.h>
+#include <asm/ehci-omap.h>
 #include "ehci-core.h"
 
+static struct omap_uhh *const uhh = (struct omap_uhh *)OMAP_UHH_BASE;
+static struct omap_usbtll *const usbtll = (struct omap_usbtll *)OMAP_USBTLL_BASE;
+static struct omap_ehci *const ehci = (struct omap_ehci *)OMAP_EHCI_BASE;
+
+static int omap_uhh_reset(void)
+{
+	unsigned long init = get_timer(0);
+
+	/* perform UHH soft reset, and wait until reset is complete */
+	writel(OMAP_UHH_SYSCONFIG_SOFTRESET, &uhh->sysc);
+
+	/* Wait for UHH reset to complete */
+	while (!(readl(&uhh->syss) & OMAP_UHH_SYSSTATUS_EHCI_RESETDONE))
+		if (get_timer(init) > CONFIG_SYS_HZ) {
+			debug("OMAP UHH error: timeout resetting ehci\n");
+			return -EL3RST;
+		}
+
+	return 0;
+}
+
+static int omap_ehci_tll_reset(void)
+{
+	unsigned long init = get_timer(0);
+
+	/* perform TLL soft reset, and wait until reset is complete */
+	writel(OMAP_USBTLL_SYSCONFIG_SOFTRESET, &usbtll->sysc);
+
+	/* Wait for TLL reset to complete */
+	while (!(readl(&usbtll->syss) & OMAP_USBTLL_SYSSTATUS_RESETDONE))
+		if (get_timer(init) > CONFIG_SYS_HZ) {
+			debug("OMAP EHCI error: timeout resetting TLL\n");
+			return -EL3RST;
+	}
+
+	return 0;
+}
+
+static void omap_usbhs_hsic_init(int port)
+{
+	unsigned int reg;
+
+	/* Enable channels now */
+	reg = readl(&usbtll->channel_conf + port);
+
+	setbits_le32(&reg, (OMAP_TLL_CHANNEL_CONF_CHANMODE_TRANSPARENT_UTMI
+		| OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
+		| OMAP_TLL_CHANNEL_CONF_DRVVBUS
+		| OMAP_TLL_CHANNEL_CONF_CHRGVBUS
+		| OMAP_TLL_CHANNEL_CONF_CHANEN));
+
+	writel(reg, &usbtll->channel_conf + port);
+}
+
+static void omap_ehci_soft_phy_reset(int port)
+{
+	struct ulpi_viewport ulpi_vp;
+
+	ulpi_vp.viewport_addr = (u32)&ehci->insreg05_utmi_ulpi;
+	ulpi_vp.port_num = port;
+
+	ulpi_reset(&ulpi_vp);
+}
+
 inline int __board_usb_init(void)
 {
 	return 0;
@@ -72,31 +136,31 @@ static inline void omap_ehci_phy_reset(int on, int delay)
 #endif
 
 /* Reset is needed otherwise the kernel-driver will throw an error. */
-int ehci_hcd_stop(void)
+int omap_ehci_hcd_stop(void)
 {
-	debug("Resetting OMAP3 EHCI\n");
+	debug("Resetting OMAP EHCI\n");
 	omap_ehci_phy_reset(1, 0);
-	writel(OMAP_UHH_SYSCONFIG_SOFTRESET,
-			OMAP3_UHH_BASE + OMAP_UHH_SYSCONFIG);
-	/* disable USB clocks */
-	struct prcm *prcm_base = (struct prcm *)PRCM_BASE;
-	sr32(&prcm_base->iclken_usbhost, 0, 1, 0);
-	sr32(&prcm_base->fclken_usbhost, 0, 2, 0);
-	sr32(&prcm_base->iclken3_core, 2, 1, 0);
-	sr32(&prcm_base->fclken3_core, 2, 1, 0);
+
+	if (omap_uhh_reset() < 0)
+		return -1;
+
+	if (omap_ehci_tll_reset() < 0)
+		return -1;
+
 	return 0;
 }
 
 /*
- * Initialize the OMAP3 EHCI controller and PHY.
- * Based on "drivers/usb/host/ehci-omap.c" from Linux 2.6.37.
+ * Initialize the OMAP EHCI controller and PHY.
+ * Based on "drivers/usb/host/ehci-omap.c" from Linux 3.1
  * See there for additional Copyrights.
  */
-int ehci_hcd_init(void)
+int omap_ehci_hcd_init(struct omap_usbhs_board_data *usbhs_pdata)
 {
 	int ret;
+	unsigned int i, reg = 0, rev = 0;
 
-	debug("Initializing OMAP3 EHCI\n");
+	debug("Initializing OMAP EHCI\n");
 
 	ret = board_usb_init();
 	if (ret < 0)
@@ -105,52 +169,87 @@ int ehci_hcd_init(void)
 	/* Put the PHY in RESET */
 	omap_ehci_phy_reset(1, 10);
 
-	struct prcm *prcm_base = (struct prcm *)PRCM_BASE;
-	/* Enable USBHOST_L3_ICLK (USBHOST_MICLK) */
-	sr32(&prcm_base->iclken_usbhost, 0, 1, 1);
-	/*
-	 * Enable USBHOST_48M_FCLK (USBHOST_FCLK1)
-	 * and USBHOST_120M_FCLK (USBHOST_FCLK2)
-	 */
-	sr32(&prcm_base->fclken_usbhost, 0, 2, 3);
-	/* Enable USBTTL_ICLK */
-	sr32(&prcm_base->iclken3_core, 2, 1, 1);
-	/* Enable USBTTL_FCLK */
-	sr32(&prcm_base->fclken3_core, 2, 1, 1);
-	debug("USB clocks enabled\n");
+	ret = omap_uhh_reset();
+	if (ret < 0)
+		return ret;
 
-	/* perform TLL soft reset, and wait until reset is complete */
-	writel(OMAP_USBTLL_SYSCONFIG_SOFTRESET,
-		OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSCONFIG);
-	/* Wait for TLL reset to complete */
-	while (!(readl(OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSSTATUS)
-			& OMAP_USBTLL_SYSSTATUS_RESETDONE))
-		;
-	debug("TLL reset done\n");
+	ret = omap_ehci_tll_reset();
+	if (ret)
+		return ret;
 
 	writel(OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
 		OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
-		OMAP_USBTLL_SYSCONFIG_CACTIVITY,
-		OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSCONFIG);
+		OMAP_USBTLL_SYSCONFIG_CACTIVITY, &usbtll->sysc);
 
 	/* Put UHH in NoIdle/NoStandby mode */
-	writel(OMAP_UHH_SYSCONFIG_ENAWAKEUP
-		| OMAP_UHH_SYSCONFIG_SIDLEMODE
-		| OMAP_UHH_SYSCONFIG_CACTIVITY
-		| OMAP_UHH_SYSCONFIG_MIDLEMODE,
-		OMAP3_UHH_BASE + OMAP_UHH_SYSCONFIG);
-
-	/* setup burst configurations */
-	writel(OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN
-		| OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN
-		| OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN,
-		OMAP3_UHH_BASE + OMAP_UHH_HOSTCONFIG);
+	writel(OMAP_UHH_SYSCONFIG_VAL, &uhh->sysc);
+
+	/* setup ULPI bypass and burst configurations */
+	clrsetbits_le32(&reg, OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN,
+		(OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN |
+		OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN |
+		OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN));
+
+	rev = readl(&uhh->rev);
+	if (rev == OMAP_USBHS_REV1) {
+		if (is_ehci_phy_mode(usbhs_pdata->port_mode[0]))
+			clrbits_le32(&reg, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS);
+		else
+			setbits_le32(&reg, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS);
+
+		if (is_ehci_phy_mode(usbhs_pdata->port_mode[1]))
+			clrbits_le32(&reg, OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS);
+		else
+			setbits_le32(&reg, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS);
+
+		if (is_ehci_phy_mode(usbhs_pdata->port_mode[2]))
+			clrbits_le32(&reg, OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS);
+		else
+			setbits_le32(&reg, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS);
+	} else if (rev == OMAP_USBHS_REV2) {
+		clrsetbits_le32(&reg, (OMAP_P1_MODE_CLEAR | OMAP_P2_MODE_CLEAR),
+					OMAP4_UHH_HOSTCONFIG_APP_START_CLK);
+
+		/* Clear port mode fields for PHY mode*/
+
+		if (is_ehci_hsic_mode(usbhs_pdata->port_mode[0]))
+			setbits_le32(&reg, OMAP_P1_MODE_HSIC);
+
+		if (is_ehci_hsic_mode(usbhs_pdata->port_mode[1]))
+			setbits_le32(&reg, OMAP_P2_MODE_HSIC);
+
+		if (is_ehci_hsic_mode(usbhs_pdata->port_mode[2]))
+			setbits_le32(&reg, OMAP_P3_MODE_HSIC);
+	}
+
+	debug("OMAP UHH_REVISION 0x%x\n", rev);
+	writel(reg, &uhh->hostconfig);
+
+	for (i = 0; i < OMAP_HS_USB_PORTS; i++)
+		if (is_ehci_hsic_mode(usbhs_pdata->port_mode[i]))
+			omap_usbhs_hsic_init(i);
 
 	omap_ehci_phy_reset(0, 10);
 
-	hccr = (struct ehci_hccr *)(OMAP3_EHCI_BASE);
-	hcor = (struct ehci_hcor *)(OMAP3_EHCI_BASE + 0x10);
+	/*
+	 * An undocumented "feature" in the OMAP3 EHCI controller,
+	 * causes suspended ports to be taken out of suspend when
+	 * the USBCMD.Run/Stop bit is cleared (for example when
+	 * we do ehci_bus_suspend).
+	 * This breaks suspend-resume if the root-hub is allowed
+	 * to suspend. Writing 1 to this undocumented register bit
+	 * disables this feature and restores normal behavior.
+	 */
+	writel(EHCI_INSNREG04_DISABLE_UNSUSPEND, &ehci->insreg04);
+
+	for (i = 0; i < OMAP_HS_USB_PORTS; i++)
+		if (is_ehci_phy_mode(usbhs_pdata->port_mode[i]))
+			omap_ehci_soft_phy_reset(i);
+
+	dcache_disable();
+	hccr = (struct ehci_hccr *)(OMAP_EHCI_BASE);
+	hcor = (struct ehci_hcor *)(OMAP_EHCI_BASE + 0x10);
 
-	debug("OMAP3 EHCI init done\n");
+	debug("OMAP EHCI init done\n");
 	return 0;
 }