Coding style cleanup; update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>

2 files changed, 44 insertions, 45 deletions

diff --git a/doc/README.korat b/doc/README.korat
index 49cd102a85..a753f848fe 100644
--- a/doc/README.korat
+++ b/doc/README.korat
@@ -51,7 +51,6 @@ leaving preprocessor symbol "CONFIG_KORAT_PERMANENT" undefined.
 2008-02-22, Larry Johnson <lrj@acm.org>
 
 
-
 The CompactFlash(R) controller on the Korat board provides a hi-speed USB
 interface.  This may be connected to either a dedicated port on the on-board
 USB controller, or to a USB port on the PowerPC 440EPx processor.  The U-Boot
diff --git a/doc/README.mpc8572ds b/doc/README.mpc8572ds
index 5a6df7f6f1..06dab596be 100644
--- a/doc/README.mpc8572ds
+++ b/doc/README.mpc8572ds
@@ -97,70 +97,70 @@ Implementing AMP(Asymmetric MultiProcessing)
 -------------
 1. Build kernel image for core0:
 
-        a. $ make 85xx/mpc8572_ds_defconfig
+	a. $ make 85xx/mpc8572_ds_defconfig
 
-        b. $ make menuconfig
-           - un-select "Processor support"->"Symetric multi-processing support"
+	b. $ make menuconfig
+	   - un-select "Processor support"->"Symetric multi-processing support"
 
-        c. $ make uImage
+	c. $ make uImage
 
 	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0
 
 2. Build kernel image for core1:
 
-        a. $ make 85xx/mpc8572_ds_defconfig
+	a. $ make 85xx/mpc8572_ds_defconfig
 
-        b. $ make menuconfig
-           - Un-select "Processor support"->"Symetric multi-processing support"
-           - Select "Advanced setup" -> " Prompt for advanced kernel
-             configuration options"
-                - Select "Set physical address where the kernel is loaded" and
-                  set it to 0x20000000, asssuming core1 will start from 512MB.
-                - Select "Set custom page offset address"
-                - Select "Set custom kernel base address"
-                - Select "Set maximum low memory"
-           - "Exit" and save the selection.
+	b. $ make menuconfig
+	   - Un-select "Processor support"->"Symetric multi-processing support"
+	   - Select "Advanced setup" -> " Prompt for advanced kernel
+	     configuration options"
+		- Select "Set physical address where the kernel is loaded" and
+		  set it to 0x20000000, asssuming core1 will start from 512MB.
+		- Select "Set custom page offset address"
+		- Select "Set custom kernel base address"
+		- Select "Set maximum low memory"
+	   - "Exit" and save the selection.
 
-        c. $ make uImage
+	c. $ make uImage
 
 	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1
 
 3. Create dtb for core0:
 
-        $ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb
+	$ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb
 
 4. Create dtb for core1:
 
-        $ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb
+	$ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb
 
 5. Bring up two cores separately:
 
-        a. Power on the board, under u-boot prompt:
-                => setenv <serverip>
-                => setenv <ipaddr>
-                => setenv bootargs root=/dev/ram rw console=ttyS0,115200
-        b. Bring up core1's kernel first:
-                => setenv bootm_low 0x20000000
-                => setenv bootm_size 0x10000000
-                => tftp 21000000 8572/uImage.core1
-                => tftp 22000000 8572/ramdiskfile
-                => tftp 20c00000 8572/mpc8572ds_core1.dtb
-                => interrupts off
-                => bootm start 21000000 22000000 20c00000
-                => bootm loados
-                => bootm ramdisk
-                => bootm fdt
-                => fdt boardsetup
-                => fdt chosen $initrd_start $initrd_end
-                => bootm prep
-                => cpu 1 release $bootm_low - $fdtaddr -
-        c. Bring up core0's kernel(on the same u-boot console):
-                => setenv bootm_low 0
-                => setenv bootm_size 0x20000000
-                => tftp 1000000 8572/uImage.core0
-                => tftp 2000000 8572/ramdiskfile
-                => tftp c00000 8572/mpc8572ds_core0.dtb
-                => bootm 1000000 2000000 c00000
+	a. Power on the board, under u-boot prompt:
+		=> setenv <serverip>
+		=> setenv <ipaddr>
+		=> setenv bootargs root=/dev/ram rw console=ttyS0,115200
+	b. Bring up core1's kernel first:
+		=> setenv bootm_low 0x20000000
+		=> setenv bootm_size 0x10000000
+		=> tftp 21000000 8572/uImage.core1
+		=> tftp 22000000 8572/ramdiskfile
+		=> tftp 20c00000 8572/mpc8572ds_core1.dtb
+		=> interrupts off
+		=> bootm start 21000000 22000000 20c00000
+		=> bootm loados
+		=> bootm ramdisk
+		=> bootm fdt
+		=> fdt boardsetup
+		=> fdt chosen $initrd_start $initrd_end
+		=> bootm prep
+		=> cpu 1 release $bootm_low - $fdtaddr -
+	c. Bring up core0's kernel(on the same u-boot console):
+		=> setenv bootm_low 0
+		=> setenv bootm_size 0x20000000
+		=> tftp 1000000 8572/uImage.core0
+		=> tftp 2000000 8572/ramdiskfile
+		=> tftp c00000 8572/mpc8572ds_core0.dtb
+		=> bootm 1000000 2000000 c00000
 
 Please note only core0 will run u-boot, core1 starts kernel directly after
 "cpu release" command is issued.