Major PCMCIA Cleanup to make code better readable and maintainable.

Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
  placed to the drivers/rpx_pmcia.c file to avoid duplication.
  Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
  board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
  the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.

1 files changed, 132 insertions, 3255 deletions

diff --git a/common/cmd_pcmcia.c b/common/cmd_pcmcia.c
index 8e3e84bed9..2eb5b26f2c 100644
--- a/common/cmd_pcmcia.c
+++ b/common/cmd_pcmcia.c
@@ -57,75 +57,14 @@
 #include <command.h>
 #include <config.h>
 #include <pcmcia.h>
-#if defined(CONFIG_8xx)
-#include <mpc8xx.h>
-#endif
-#if defined(CONFIG_LWMON)
-#include <i2c.h>
-#endif
-#ifdef CONFIG_PXA_PCMCIA
-#include <asm/arch/pxa-regs.h>
-#endif
-
 #include <asm/io.h>
 
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) || \
-    ((CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD))
-
-int pcmcia_on (void);
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int  pcmcia_off (void);
-#endif
-
-#ifdef CONFIG_I82365
-
-extern int i82365_init (void);
-extern void i82365_exit (void);
-
-#else /* ! CONFIG_I82365 */
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int  hardware_disable(int slot);
-#endif
-static int  hardware_enable (int slot);
-static int  voltage_set(int slot, int vcc, int vpp);
-
-#if (! defined(CONFIG_I82365)) && (! defined(CONFIG_PXA_PCMCIA))
-static u_int m8xx_get_graycode(u_int size);
-#endif	/* !CONFIG_I82365, !CONFIG_PXA_PCMCIA */
-#if 0
-static u_int m8xx_get_speed(u_int ns, u_int is_io);
-#endif
-
 /* -------------------------------------------------------------------- */
 
-#ifndef CONFIG_PXA_PCMCIA
-
-/* look up table for pgcrx registers */
-
-static u_int *pcmcia_pgcrx[2] = {
-	&((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pgcra,
-	&((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pgcrb,
-};
-#define PCMCIA_PGCRX(slot)	(*pcmcia_pgcrx[slot])
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
 
-#endif	/* CONFIG_PXA_PCMCIA */
-
-#endif /* CONFIG_I82365 */
-
-#if defined(CONFIG_IDE_8xx_PCCARD)  || defined(CONFIG_PXA_PCMCIA)
-static void print_funcid (int func);
-static void print_fixed  (volatile uchar *p);
-static int  identify     (volatile uchar *p);
-static int  check_ide_device (int slot);
-#endif	/* CONFIG_IDE_8xx_PCCARD, CONFIG_PXA_PCMCIA */
-
-const char *indent = "\t   ";
-
-/* -------------------------------------------------------------------- */
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+extern int pcmcia_on (void);
+extern int pcmcia_off (void);
 
 int do_pinit (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
@@ -136,7 +75,7 @@ int do_pinit (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		return 1;
 	}
 	if (strcmp(argv[1],"on") == 0) {
-	     	rcode = pcmcia_on ();
+		rcode = pcmcia_on ();
 	} else if (strcmp(argv[1],"off") == 0) {
 		rcode = pcmcia_off ();
 	} else {
@@ -146,2656 +85,82 @@ int do_pinit (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 	return rcode;
 }
-#endif	/* CFG_CMD_PCMCIA */
-
-/* -------------------------------------------------------------------- */
-
-#ifdef CONFIG_I82365
-int pcmcia_on (void)
-{
-	u_int rc;
-
-	debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
 
-	rc = i82365_init();
+U_BOOT_CMD(
+	pinit,	2,	1,	do_pinit,
+	"pinit   - PCMCIA sub-system\n",
+	"on  - power on PCMCIA socket\n"
+			"pinit off - power off PCMCIA socket\n"
+	  );
 
-	if (rc == 0) {
-		rc = check_ide_device(0);
-	}
+#endif	/* CONFIG_COMMANDS & CFG_CMD_PCMCIA */
 
-	return (rc);
-}
-#else
+/* -------------------------------------------------------------------- */
 
-#ifndef CONFIG_PXA_PCMCIA
+#undef	CHECK_IDE_DEVICE
 
-#ifdef CONFIG_HMI10
-# define  HMI10_FRAM_TIMING	(PCMCIA_SHT(2) | PCMCIA_SST(2) | PCMCIA_SL(4))
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CHECK_IDE_DEVICE
 #endif
-#if defined(CONFIG_LWMON) || defined(CONFIG_NSCU)
-# define  CFG_PCMCIA_TIMING	(PCMCIA_SHT(9) | PCMCIA_SST(3) | PCMCIA_SL(12))
-#else
-# define  CFG_PCMCIA_TIMING	(PCMCIA_SHT(2) | PCMCIA_SST(4) | PCMCIA_SL(9))
+
+#if	defined(CONFIG_PXA_PCMCIA)
+#define	CHECK_IDE_DEVICE
 #endif
 
-int pcmcia_on (void)
-{
-	int i;
-	u_long reg, base;
-	pcmcia_win_t *win;
-	u_int slotbit;
-	u_int rc, slot;
+#ifdef	CHECK_IDE_DEVICE
 
-	debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
+int		ide_devices_found;
+static uchar	*known_cards[] = {
+	(uchar *)"ARGOSY PnPIDE D5",
+	NULL
+};
 
-	/* intialize the fixed memory windows */
-	win = (pcmcia_win_t *)(&((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pbr0);
-	base = CFG_PCMCIA_MEM_ADDR;
+#define	MAX_TUPEL_SZ	512
+#define MAX_FEATURES	4
 
-	if((reg = m8xx_get_graycode(CFG_PCMCIA_MEM_SIZE)) == -1) {
-		printf ("Cannot set window size to 0x%08x\n",
-			CFG_PCMCIA_MEM_SIZE);
-		return (1);
-	}
+#define MAX_IDENT_CHARS		64
+#define	MAX_IDENT_FIELDS	4
 
-	slotbit = PCMCIA_SLOT_x;
-	for (i=0; i<PCMCIA_MEM_WIN_NO; ++i) {
-		win->br = base;
+#define	indent	"\t   "
 
-#if (PCMCIA_SOCKETS_NO == 2)
-		if (i == 4) /* Another slot starting from win 4 */
-			slotbit = (slotbit ? PCMCIA_PSLOT_A : PCMCIA_PSLOT_B);
-#endif
-		switch (i) {
-#ifdef CONFIG_IDE_8xx_PCCARD
-		case 4:
-#ifdef CONFIG_HMI10
-		    {	/* map FRAM area */
-			win->or = (	PCMCIA_BSIZE_256K
-				|	PCMCIA_PPS_8
-				|	PCMCIA_PRS_ATTR
-				|	slotbit
-				|	PCMCIA_PV
-				|	HMI10_FRAM_TIMING );
-			break;
-		    }
-#endif
-		case 0:	{	/* map attribute memory */
-			win->or = (	PCMCIA_BSIZE_64M
-				|	PCMCIA_PPS_8
-				|	PCMCIA_PRS_ATTR
-				|	slotbit
-				|	PCMCIA_PV
-				|	CFG_PCMCIA_TIMING );
+static void print_funcid (int func)
+{
+	puts (indent);
+	switch (func) {
+		case CISTPL_FUNCID_MULTI:
+			puts (" Multi-Function");
 			break;
-		    }
-		case 5:
-		case 1: {	/* map I/O window for data reg */
-			win->or = (	PCMCIA_BSIZE_1K
-				|	PCMCIA_PPS_16
-				|	PCMCIA_PRS_IO
-				|	slotbit
-				|	PCMCIA_PV
-				|	CFG_PCMCIA_TIMING );
+		case CISTPL_FUNCID_MEMORY:
+			puts (" Memory");
 			break;
-		    }
-		case 6:
-		case 2: {	/* map I/O window for cmd/ctrl reg block */
-			win->or = (	PCMCIA_BSIZE_1K
-				|	PCMCIA_PPS_8
-				|	PCMCIA_PRS_IO
-				|	slotbit
-				|	PCMCIA_PV
-				|	CFG_PCMCIA_TIMING );
+		case CISTPL_FUNCID_SERIAL:
+			puts (" Serial Port");
 			break;
-		    }
-#endif	/* CONFIG_IDE_8xx_PCCARD */
-#ifdef CONFIG_HMI10
-		case 3: {	/* map I/O window for 4xUART data/ctrl */
-			win->br += 0x40000;
-			win->or = (	PCMCIA_BSIZE_256K
-				|	PCMCIA_PPS_8
-				|	PCMCIA_PRS_IO
-				|	slotbit
-				|	PCMCIA_PV
-				|	CFG_PCMCIA_TIMING );
+		case CISTPL_FUNCID_PARALLEL:
+			puts (" Parallel Port");
 			break;
-		    }
-#endif /* CONFIG_HMI10 */
-		default:	/* set to not valid */
-			win->or = 0;
+		case CISTPL_FUNCID_FIXED:
+			puts (" Fixed Disk");
 			break;
-		}
-
-		debug ("MemWin %d: PBR 0x%08lX  POR %08lX\n",
-			i, win->br, win->or);
-		base += CFG_PCMCIA_MEM_SIZE;
-		++win;
-	}
-
-	for (i=0, rc=0, slot=_slot_; i<PCMCIA_SOCKETS_NO; i++, slot = !slot) {
-		/* turn off voltage */
-		if ((rc = voltage_set(slot, 0, 0)))
-			continue;
-
-		/* Enable external hardware */
-		if ((rc = hardware_enable(slot)))
-			continue;
-
-#ifdef CONFIG_IDE_8xx_PCCARD
-		if ((rc = check_ide_device(i)))
-			continue;
-#endif
-	}
-	return (rc);
-}
-
-#endif /* CONFIG_PXA_PCMCIA */
-
-#endif /* CONFIG_I82365 */
-
-#ifdef CONFIG_PXA_PCMCIA
-
-static int hardware_enable (int slot)
-{
-	return 0;	/* No hardware to enable */
-}
-
-static int hardware_disable(int slot)
-{
-	return 0;	/* No hardware to disable */
-}
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	return 0;
-}
-
-void msWait(unsigned msVal)
-{
-	udelay(msVal*1000);
-}
-
-int pcmcia_on (void)
-{
-	unsigned int reg_arr[] = {
-		0x48000028, CFG_MCMEM0_VAL,
-		0x4800002c, CFG_MCMEM1_VAL,
-		0x48000030, CFG_MCATT0_VAL,
-		0x48000034, CFG_MCATT1_VAL,
-		0x48000038, CFG_MCIO0_VAL,
-		0x4800003c, CFG_MCIO1_VAL,
-
-		0, 0
-	};
-	int i, rc;
-
-#ifdef CONFIG_EXADRON1
-	int cardDetect;
-	volatile unsigned int *v_pBCRReg =
-		(volatile unsigned int *) 0x08000000;
-#endif
-
-	debug ("%s\n", __FUNCTION__);
-
-	i = 0;
-	while (reg_arr[i])
-		*((volatile unsigned int *) reg_arr[i++]) |= reg_arr[i++];
-	udelay (1000);
-
-	debug ("%s: programmed mem controller \n", __FUNCTION__);
-
-#ifdef CONFIG_EXADRON1
-
-/*define useful BCR masks */
-#define BCR_CF_INIT_VAL  		    0x00007230
-#define BCR_CF_PWRON_BUSOFF_RESETOFF_VAL    0x00007231
-#define BCR_CF_PWRON_BUSOFF_RESETON_VAL     0x00007233
-#define BCR_CF_PWRON_BUSON_RESETON_VAL      0x00007213
-#define BCR_CF_PWRON_BUSON_RESETOFF_VAL     0x00007211
-
-	/* we see from the GPIO bit if the card is present */
-	cardDetect = !(GPLR0 & GPIO_bit (14));
-
-	if (cardDetect) {
-		printf ("No PCMCIA card found!\n");
-	}
-
-	/* reset the card via the BCR line */
-	*v_pBCRReg = (unsigned) BCR_CF_INIT_VAL;
-	msWait (500);
-
-	*v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSOFF_RESETOFF_VAL;
-	msWait (500);
-
-	*v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSOFF_RESETON_VAL;
-	msWait (500);
-
-	*v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSON_RESETON_VAL;
-	msWait (500);
-
-	*v_pBCRReg = (unsigned) BCR_CF_PWRON_BUSON_RESETOFF_VAL;
-	msWait (1500);
-
-	/* enable address bus */
-	GPCR1 = 0x01;
-	/* and the first CF slot */
-	MECR = 0x00000002;
-
-#endif /* EXADRON 1 */
-
-	rc = check_ide_device (0);	/* use just slot 0 */
-
-	return rc;
-}
-
-#endif /* CONFIG_PXA_PCMCIA */
-
-/* -------------------------------------------------------------------- */
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-
-#ifdef CONFIG_I82365
-static int pcmcia_off (void)
-{
-	printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
-	i82365_exit();
-
-	return 0;
-}
-#else
-
-#ifndef CONFIG_PXA_PCMCIA
-
-static int pcmcia_off (void)
-{
-	int i;
-	pcmcia_win_t *win;
-
-	printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
-	/* clear interrupt state, and disable interrupts */
-	((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pscr =  PCMCIA_MASK(_slot_);
-	((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_per &= ~PCMCIA_MASK(_slot_);
-
-	/* turn off interrupt and disable CxOE */
-	PCMCIA_PGCRX(_slot_) = __MY_PCMCIA_GCRX_CXOE;
-
-	/* turn off memory windows */
-	win = (pcmcia_win_t *)(&((immap_t *)CFG_IMMR)->im_pcmcia.pcmc_pbr0);
-
-	for (i=0; i<PCMCIA_MEM_WIN_NO; ++i) {
-		/* disable memory window */
-		win->or = 0;
-		++win;
-	}
-
-	/* turn off voltage */
-	voltage_set(_slot_, 0, 0);
-
-	/* disable external hardware */
-	printf ("Shutdown and Poweroff " PCMCIA_SLOT_MSG "\n");
-	hardware_disable(_slot_);
-	return 0;
-}
-
-#endif /* CONFIG_PXA_PCMCIA */
-
-#endif /* CONFIG_I82365 */
-
-#ifdef CONFIG_PXA_PCMCIA
-static int pcmcia_off (void)
-{
-	return 0;
-}
-#endif
-
-#endif	/* CFG_CMD_PCMCIA */
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-
-#define	MAX_TUPEL_SZ	512
-#define MAX_FEATURES	4
-
-int ide_devices_found;
-static int check_ide_device (int slot)
-{
-	volatile uchar *ident = NULL;
-	volatile uchar *feature_p[MAX_FEATURES];
-	volatile uchar *p, *start, *addr;
-	int n_features = 0;
-	uchar func_id = ~0;
-	uchar code, len;
-	ushort config_base = 0;
-	int found = 0;
-	int i;
-
-	addr = (volatile uchar *)(CFG_PCMCIA_MEM_ADDR +
-				  CFG_PCMCIA_MEM_SIZE * (slot * 4));
-	debug ("PCMCIA MEM: %08lX\n", (ulong)addr);
-
-	start = p = (volatile uchar *) addr;
-
-	while ((p - start) < MAX_TUPEL_SZ) {
-
-		code = *p; p += 2;
-
-		if (code == 0xFF) { /* End of chain */
+		case CISTPL_FUNCID_VIDEO:
+			puts (" Video Adapter");
 			break;
-		}
-
-		len = *p; p += 2;
-#if defined(DEBUG) && (DEBUG > 1)
-		{ volatile uchar *q = p;
-			printf ("\nTuple code %02x  length %d\n\tData:",
-				code, len);
-
-			for (i = 0; i < len; ++i) {
-				printf (" %02x", *q);
-				q+= 2;
-			}
-		}
-#endif	/* DEBUG */
-		switch (code) {
-		case CISTPL_VERS_1:
-			ident = p + 4;
+		case CISTPL_FUNCID_NETWORK:
+			puts (" Network Adapter");
 			break;
-		case CISTPL_FUNCID:
-			/* Fix for broken SanDisk which may have 0x80 bit set */
-			func_id = *p & 0x7F;
+		case CISTPL_FUNCID_AIMS:
+			puts (" AIMS Card");
 			break;
-		case CISTPL_FUNCE:
-			if (n_features < MAX_FEATURES)
-				feature_p[n_features++] = p;
+		case CISTPL_FUNCID_SCSI:
+			puts (" SCSI Adapter");
 			break;
-		case CISTPL_CONFIG:
-			config_base = (*(p+6) << 8) + (*(p+4));
-			debug ("\n## Config_base = %04x ###\n", config_base);
 		default:
+			puts (" Unknown");
 			break;
-		}
-		p += 2 * len;
-	}
-
-	found = identify (ident);
-
-	if (func_id != ((uchar)~0)) {
-		print_funcid (func_id);
-
-		if (func_id == CISTPL_FUNCID_FIXED)
-			found = 1;
-		else
-			return (1);	/* no disk drive */
-	}
-
-	for (i=0; i<n_features; ++i) {
-		print_fixed (feature_p[i]);
-	}
-
-	if (!found) {
-		printf ("unknown card type\n");
-		return (1);
-	}
-
-	ide_devices_found |= (1 << slot);
-
-#if CONFIG_CPC45
-#else
-	/* set I/O area in config reg -> only valid for ARGOSY D5!!! */
-	*((uchar *)(addr + config_base)) = 1;
-#endif
-#if 0
-	printf("\n## Config_base = %04x ###\n", config_base);
-	printf("Configuration Option Register: %02x @ %x\n", readb(addr + config_base), addr + config_base);
-	printf("Card Configuration and Status Register: %02x\n", readb(addr + config_base + 2));
-	printf("Pin Replacement Register Register: %02x\n", readb(addr + config_base + 4));
-	printf("Socket and Copy Register: %02x\n", readb(addr + config_base + 6));
-#endif
-	return (0);
-}
-#endif	/* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
-
-
-/* -------------------------------------------------------------------- */
-/* board specific stuff:						*/
-/* voltage_set(), hardware_enable() and hardware_disable()		*/
-/* -------------------------------------------------------------------- */
-
-/* -------------------------------------------------------------------- */
-/* RPX Boards from Embedded Planet					*/
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE)
-
-/* The RPX boards seems to have it's bus monitor timeout set to 6*8 clocks.
- * SYPCR is write once only, therefore must the slowest memory be faster
- * than the bus monitor or we will get a machine check due to the bus timeout.
- */
-
-#define PCMCIA_BOARD_MSG "RPX CLASSIC or RPX LITE"
-
-#undef PCMCIA_BMT_LIMIT
-#define PCMCIA_BMT_LIMIT (6*8)
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	u_long reg = 0;
-
-	switch(vcc) {
-	case 0: break;
-	case 33: reg |= BCSR1_PCVCTL4; break;
-	case 50: reg |= BCSR1_PCVCTL5; break;
-	default: return 1;
-	}
-
-	switch(vpp) {
-	case 0: break;
-	case 33:
-	case 50:
-		if(vcc == vpp)
-			reg |= BCSR1_PCVCTL6;
-		else
-			return 1;
-		break;
-	case 120:
-		reg |= BCSR1_PCVCTL7;
-	default: return 1;
-	}
-
-	if(vcc == 120)
-	   return 1;
-
-	/* first, turn off all power */
-
-	*((uint *)RPX_CSR_ADDR) &= ~(BCSR1_PCVCTL4 | BCSR1_PCVCTL5
-				     | BCSR1_PCVCTL6 | BCSR1_PCVCTL7);
-
-	/* enable new powersettings */
-
-	*((uint *)RPX_CSR_ADDR) |= reg;
-
-	return 0;
-}
-
-#define socket_get(_slot_) PCMCIA_SOCKET_KEY_5V
-static int hardware_enable (int slot)
-{
-	return 0;	/* No hardware to enable */
-}
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	return 0;	/* No hardware to disable */
-}
-#endif	/* CFG_CMD_PCMCIA */
-#endif	/* CONFIG_RPXCLASSIC */
-
-/* -------------------------------------------------------------------- */
-/* (F)ADS Boards from Motorola						*/
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ADS) || defined(CONFIG_FADS)
-
-#ifdef CONFIG_ADS
-#define PCMCIA_BOARD_MSG "ADS"
-#define PCMCIA_GLITCHY_CD  /* My ADS board needs this */
-#else
-#define PCMCIA_BOARD_MSG "FADS"
-#endif
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	u_long reg = 0;
-
-	switch(vpp) {
-	case 0: reg = 0; break;
-	case 50: reg = 1; break;
-	case 120: reg = 2; break;
-	default: return 1;
-	}
-
-	switch(vcc) {
-	case 0: reg = 0; break;
-#ifdef CONFIG_ADS
-	case 50: reg = BCSR1_PCCVCCON; break;
-#endif
-#ifdef CONFIG_FADS
-	case 33: reg = BCSR1_PCCVCC0 | BCSR1_PCCVCC1; break;
-	case 50: reg = BCSR1_PCCVCC1; break;
-#endif
-	default: return 1;
-	}
-
-	/* first, turn off all power */
-
-#ifdef CONFIG_ADS
-	*((uint *)BCSR1) |= BCSR1_PCCVCCON;
-#endif
-#ifdef CONFIG_FADS
-	*((uint *)BCSR1) &= ~(BCSR1_PCCVCC0 | BCSR1_PCCVCC1);
-#endif
-	*((uint *)BCSR1) &= ~BCSR1_PCCVPP_MASK;
-
-	/* enable new powersettings */
-
-#ifdef CONFIG_ADS
-	*((uint *)BCSR1) &= ~reg;
-#endif
-#ifdef CONFIG_FADS
-	*((uint *)BCSR1) |= reg;
-#endif
-
- 	*((uint *)BCSR1) |= reg << 20;
-
-	return 0;
-}
-
-#define socket_get(_slot_) PCMCIA_SOCKET_KEY_5V
-
-static int hardware_enable(int slot)
-{
-	*((uint *)BCSR1) &= ~BCSR1_PCCEN;
-	return 0;
-}
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	*((uint *)BCSR1) &= ~BCSR1_PCCEN;
-	return 0;
-}
-#endif	/* CFG_CMD_PCMCIA */
-
-#endif	/* (F)ADS */
-
-/* -------------------------------------------------------------------- */
-/* TQM8xxL Boards by TQ Components					*/
-/* SC8xx   Boards by SinoVee Microsystems				*/
-/* -------------------------------------------------------------------- */
-
-#if (defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx)) \
-	&& !defined(CONFIG_VIRTLAB2)
-
-#if defined(CONFIG_TQM8xxL)
-#define PCMCIA_BOARD_MSG "TQM8xxL"
-#endif
-#if defined(CONFIG_SVM_SC8xx)
-#define PCMCIA_BOARD_MSG "SC8xx"
-#endif
-
-static int hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, mask;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	immap = (immap_t *)CFG_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/*
-	 * Configure SIUMCR to enable PCMCIA port B
-	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-	 */
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(slot);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-#ifndef NSCU_OE_INV
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-#endif
-	PCMCIA_PGCRX(slot) = reg;
-	udelay(500);
-
-#ifndef CONFIG_HMI10
-#ifndef CONFIG_NSCU
-	/*
-	 * Configure Port C pins for
-	 * 5 Volts Enable and 3 Volts enable
-	 */
-	immap->im_ioport.iop_pcpar &= ~(0x0002 | 0x0004);
-	immap->im_ioport.iop_pcso  &= ~(0x0002 | 0x0004);
-	/* remove all power */
-
-	immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
-#endif
-#else	/* CONFIG_HMI10 */
-	/*
-	 * Configure Port B  pins for
-	 * 5 Volts Enable and 3 Volts enable
-	 */
-	immap->im_cpm.cp_pbpar &= ~(0x00000300);
-
-	/* remove all power */
-	immap->im_cpm.cp_pbdat |= 0x00000300;
-#endif	/* CONFIG_HMI10 */
-
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-#ifndef CONFIG_HMI10
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-#else
-	if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
-#endif	/* CONFIG_HMI10 */
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	 * Power On.
-	 */
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	reg  = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-		reg,
-		(reg&PCMCIA_VS1(slot))?"n":"ff",
-		(reg&PCMCIA_VS2(slot))?"n":"ff");
-#ifndef CONFIG_NSCU
-	if ((reg & mask) == mask) {
-#ifndef CONFIG_HMI10
-		immap->im_ioport.iop_pcdat |= 0x0004;
-#else
-		immap->im_cpm.cp_pbdat &= ~(0x0000100);
-#endif	/* CONFIG_HMI10 */
-		puts (" 5.0V card found: ");
-	} else {
-#ifndef CONFIG_HMI10
-		immap->im_ioport.iop_pcdat |= 0x0002;
-#else
-		immap->im_cpm.cp_pbdat &= ~(0x0000200);
-#endif	/* CONFIG_HMI10 */
-		puts (" 3.3V card found: ");
-	}
-#ifndef CONFIG_HMI10
-	immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004);
-#else
-	immap->im_cpm.cp_pbdir |= 0x00000300;
-#endif	/* CONFIG_HMI10 */
-#else
-	if ((reg & mask) == mask) {
-		puts (" 5.0V card found: ");
-	} else {
-		puts (" 3.3V card found: ");
-	}
-#endif
-#if 0
-	/*  VCC switch error flag, PCMCIA slot INPACK_ pin */
-	cp->cp_pbdir &= ~(0x0020 | 0x0010);
-	cp->cp_pbpar &= ~(0x0020 | 0x0010);
-	udelay(500000);
-#endif
-	udelay(1000);
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(slot);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-#ifndef NSCU_OE_INV
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-#else
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-#endif
-	PCMCIA_PGCRX(slot) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
-#ifndef CONFIG_HMI10
-#ifndef CONFIG_NSCU
-	/* remove all power */
-	immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
-#endif
-#else	/* CONFIG_HMI10 */
-	immap->im_cpm.cp_pbdat |= 0x00000300;
-#endif	/* CONFIG_HMI10 */
-
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-#ifndef NSCU_OE_INV
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-#endif
-	PCMCIA_PGCRX(slot) = reg;
-
-	udelay(10000);
-
-	return (0);
-}
-#endif	/* CFG_CMD_PCMCIA */
-
-#ifdef CONFIG_NSCU
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	return 0;
-}
-#else
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("voltage_set: "
-		PCMCIA_BOARD_MSG
-		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	/*
-	 * Disable PCMCIA buffers (isolate the interface)
-	 * and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(slot);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-#ifndef NSCU_OE_INV
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-#else
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-#endif
-	PCMCIA_PGCRX(slot) = reg;
-	udelay(500);
-
-#ifndef CONFIG_HMI10
-	/*
-	 * Configure Port C pins for
-	 * 5 Volts Enable and 3 Volts enable,
-	 * Turn off all power
-	 */
-	debug ("PCMCIA power OFF\n");
-	immap->im_ioport.iop_pcpar &= ~(0x0002 | 0x0004);
-	immap->im_ioport.iop_pcso  &= ~(0x0002 | 0x0004);
-	immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004);
-
-	reg = 0;
-	switch(vcc) {
-	case  0: 		break;
-	case 33: reg |= 0x0002;	break;
-	case 50: reg |= 0x0004;	break;
-	default: 		goto done;
-	}
-#else	/* CONFIG_HMI10 */
-	/*
-	 * Configure Port B pins for
-	 * 5 Volts Enable and 3 Volts enable,
-	 * Turn off all power
-	 */
-	debug ("PCMCIA power OFF\n");
-	immap->im_cpm.cp_pbpar &= ~(0x00000300);
-	/* remove all power */
-
-	immap->im_cpm.cp_pbdat |= 0x00000300;
-
-	reg = 0;
-	switch(vcc) {
-		case  0:			break;
-		case 33: reg |= 0x00000200;	break;
-		case 50: reg |= 0x00000100;	break;
-		default:			goto done;
-}
-#endif	/* CONFIG_HMI10 */
-
-	/* Checking supported voltages */
-
-	debug ("PIPR: 0x%x --> %s\n",
-		pcmp->pcmc_pipr,
-		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-#ifndef CONFIG_HMI10
-	immap->im_ioport.iop_pcdat |= reg;
-	immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004);
-#else
-	immap->im_cpm.cp_pbdat &= !reg;
-	immap->im_cpm.cp_pbdir |= 0x00000300;
-#endif	/* CONFIG_HMI10 */
-	if (reg) {
-#ifndef CONFIG_HMI10
-		debug ("PCMCIA powered at %sV\n",
-			(reg&0x0004) ? "5.0" : "3.3");
-#else
-		debug ("PCMCIA powered at %sV\n",
-			(reg&0x00000200) ? "5.0" : "3.3");
-#endif	/* CONFIG_HMI10 */
-	} else {
-		debug ("PCMCIA powered down\n");
-	}
-
-done:
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(slot);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-#ifndef NSCU_OE_INV
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-#else
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-#endif
-	PCMCIA_PGCRX(slot) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-		slot+'A');
-	return (0);
-}
-#endif
-
-#endif	/* TQM8xxL */
-
-/* -------------------------------------------------------------------- */
-/* Virtlab2 Board by TQ Components					*/
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_VIRTLAB2)
-#define PCMCIA_BOARD_MSG "Virtlab2"
-
-static int hardware_enable(int slot)
-{
-	volatile pcmconf8xx_t	*pcmp =
-		(pcmconf8xx_t *)&(((immap_t *)CFG_IMMR)->im_pcmcia);
-	volatile unsigned char	*powerctl =
-		(volatile unsigned char *)PCMCIA_CTRL;
-	volatile sysconf8xx_t	*sysp =
-		(sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-	unsigned int		reg, mask;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	/*
-	 * Configure SIUMCR to enable PCMCIA port B
-	 */
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(slot);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg = __MY_PCMCIA_GCRX_CXRESET;		/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-
-	PCMCIA_PGCRX(slot) = reg;
-	udelay(500);
-
-	/* remove all power */
-	*powerctl = 0;
-
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n", __LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	 * Power On.
-	 */
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	reg  = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
-		(reg&PCMCIA_VS1(slot))?"n":"ff",
-		(reg&PCMCIA_VS2(slot))?"n":"ff");
-
-	if ((reg & mask) == mask) {
-		*powerctl = 2;	/* Enable 5V Vccout */
-		puts (" 5.0V card found: ");
-	} else {
-		*powerctl = 1;	/* Enable 3.3 V Vccout */
-		puts (" 3.3V card found: ");
-	}
-
-	udelay(1000);
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(slot);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-
-	PCMCIA_PGCRX(slot) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	volatile unsigned char	*powerctl =
-		(volatile unsigned char *)PCMCIA_CTRL;
-	unsigned long		 reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	/* remove all power */
-	*powerctl = 0;
-
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg = __MY_PCMCIA_GCRX_CXRESET;		/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-
-	PCMCIA_PGCRX(slot) = reg;
-
-	udelay(10000);
-
-	return (0);
-}
-#endif
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-#ifdef DEBUG
-	volatile pcmconf8xx_t	*pcmp =
-		(pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-#endif
-	volatile unsigned char	*powerctl =
-		(volatile unsigned char *)PCMCIA_CTRL;
-	unsigned long		reg;
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG
-		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	/*
-	 * Disable PCMCIA buffers (isolate the interface)
-	 * and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(slot);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-
-	PCMCIA_PGCRX(slot) = reg;
-	udelay(500);
-
-	/*
-	 * Configure pins for 5 Volts Enable and 3 Volts enable,
-	 * Turn off all power.
-	 */
-	debug ("PCMCIA power OFF\n");
-	reg = 0;
-	switch(vcc) {
-	case  0: 		break;
-	case 33: reg = 0x0001;	break;
-	case 50: reg = 0x0002;	break;
-	default: 		goto done;
-	}
-
-	/* Checking supported voltages */
-
-	debug ("PIPR: 0x%x --> %s\n", pcmp->pcmc_pipr,
-		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-	*powerctl = reg;
-
-	if (reg) {
-		debug ("PCMCIA powered at %sV\n", (reg&0x0004) ? "5.0" : "3.3");
-	} else {
-		debug ("PCMCIA powered down\n");
-	}
-
-done:
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(slot);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-
-	PCMCIA_PGCRX(slot) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", slot+'A');
-	return (0);
-}
-#endif	/* CONFIG_VIRTLAB2 */
-
-/* -------------------------------------------------------------------- */
-/* LWMON Board								*/
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_LWMON)
-
-#define PCMCIA_BOARD_MSG "LWMON"
-
-/* #define's for MAX1604 Power Switch */
-#define MAX1604_OP_SUS		0x80
-#define MAX1604_VCCBON		0x40
-#define MAX1604_VCC_35		0x20
-#define MAX1604_VCCBHIZ		0x10
-#define MAX1604_VPPBON		0x08
-#define MAX1604_VPPBPBPGM	0x04
-#define MAX1604_VPPBHIZ		0x02
-/* reserved			0x01	*/
-
-static int hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, mask;
-	uchar val;
-
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	/* Switch on PCMCIA port in PIC register 0x60 */
-	reg = pic_read  (0x60);
-	debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-	reg &= ~0x10;
-	/* reg |= 0x08; Vpp not needed */
-	pic_write (0x60, reg);
-#ifdef DEBUG
-	reg = pic_read  (0x60);
-	printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-#endif
-	udelay(10000);
-
-	immap = (immap_t *)CFG_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/*
-	 * Configure SIUMCR to enable PCMCIA port B
-	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-	 */
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	 * Power On.
-	 */
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	reg  = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-		reg,
-		(reg&PCMCIA_VS1(slot))?"n":"ff",
-		(reg&PCMCIA_VS2(slot))?"n":"ff");
-	if ((reg & mask) == mask) {
-		val = 0;		/* VCCB3/5 = 0 ==> use Vx = 5.0 V */
-		puts (" 5.0V card found: ");
-	} else {
-		val = MAX1604_VCC_35;	/* VCCB3/5 = 1 ==> use Vy = 3.3 V */
-		puts (" 3.3V card found: ");
-	}
-
-	/*  switch VCC on */
-	val |= MAX1604_OP_SUS | MAX1604_VCCBON;
-	i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
-	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
-	udelay(500000);
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-	uchar val;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
-	/* remove all power, put output in high impedance state */
-	val  = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
-	i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
-	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
-	/* Configure PCMCIA General Control Register */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	/* Switch off PCMCIA port in PIC register 0x60 */
-	reg = pic_read  (0x60);
-	debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-	reg |=  0x10;
-	reg &= ~0x08;
-	pic_write (0x60, reg);
-#ifdef DEBUG
-	reg = pic_read  (0x60);
-	printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-#endif
-	udelay(10000);
-
-	return (0);
-}
-#endif	/* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-	uchar val;
-
-	debug ("voltage_set: "
-		PCMCIA_BOARD_MSG
-		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	/*
-	 * Disable PCMCIA buffers (isolate the interface)
-	 * and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(_slot_);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Turn off all power (switch to high impedance)
-	 */
-	debug ("PCMCIA power OFF\n");
-	val  = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
-	i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
-	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
-	val = 0;
-	switch(vcc) {
-	case  0: 			break;
-	case 33: val = MAX1604_VCC_35;	break;
-	case 50: 			break;
-	default: 			goto done;
-	}
-
-	/* Checking supported voltages */
-
-	debug ("PIPR: 0x%x --> %s\n",
-		pcmp->pcmc_pipr,
-		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-	if (val) {
-		debug ("PCMCIA powered at %sV\n",
-			(val & MAX1604_VCC_35) ? "3.3" : "5.0");
-	} else {
-		debug ("PCMCIA powered down\n");
-	}
-
-done:
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-		slot+'A');
-	return (0);
-}
-
-#endif	/* LWMON */
-
-/* -------------------------------------------------------------------- */
-/* GTH board by Corelatus AB						*/
-/* -------------------------------------------------------------------- */
-#if defined(CONFIG_GTH)
-
-#define PCMCIA_BOARD_MSG "GTH COMPACT FLASH"
-
-static int voltage_set (int slot, int vcc, int vpp)
-{	/* Do nothing */
-	return 0;
-}
-
-static int hardware_enable (int slot)
-{
-	volatile immap_t *immap;
-	volatile cpm8xx_t *cp;
-	volatile pcmconf8xx_t *pcmp;
-	volatile sysconf8xx_t *sysp;
-	uint reg, mask;
-
-	debug ("hardware_enable: GTH Slot %c\n", 'A' + slot);
-
-	immap = (immap_t *) CFG_IMMR;
-	sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
-	pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
-	cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;	/* active low  */
-	PCMCIA_PGCRX (_slot_) = reg;
-	udelay (500);
-
-	/*
-	 * Make sure there is a card in the slot,
-	 * then configure the interface.
-	 */
-	udelay (10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__, __FUNCTION__,
-		&(pcmp->pcmc_pipr), pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & 0x98000000) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	mask = PCMCIA_VS1 (slot) | PCMCIA_VS2 (slot);
-	reg = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-		   reg,
-		   (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
-		   (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX (_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX (_slot_) = reg;
-
-	udelay (250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return 0;
-}
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	return 0;	/* No hardware to disable */
-}
-#endif	/* CFG_CMD_PCMCIA */
-#endif	/* CONFIG_GTH */
-
-/* -------------------------------------------------------------------- */
-/* ICU862 Boards by Cambridge Broadband Ltd.				*/
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ICU862)
-
-#define PCMCIA_BOARD_MSG "ICU862"
-
-static void cfg_port_B (void);
-
-static int hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, pipr, mask;
-	int i;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	immap = (immap_t *)CFG_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/* Configure Port B for TPS2205 PC-Card Power-Interface Switch */
-	cfg_port_B ();
-
-	/*
-	 * Configure SIUMCR to enable PCMCIA port B
-	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-	 */
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	 * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
-	 */
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	pipr = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-		pipr,
-		(reg&PCMCIA_VS1(slot))?"n":"ff",
-		(reg&PCMCIA_VS2(slot))?"n":"ff");
-
-	reg  = cp->cp_pbdat;
-	if ((pipr & mask) == mask) {
-		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
-			TPS2205_VCC3);				/* 3V off	*/
-		reg &= ~(TPS2205_VCC5);				/* 5V on	*/
-		puts (" 5.0V card found: ");
-	} else {
-		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
-			TPS2205_VCC5);				/* 5V off	*/
-		reg &= ~(TPS2205_VCC3);				/* 3V on	*/
-		puts (" 3.3V card found: ");
-	}
-
-	debug ("\nPB DAT: %08x -> 3.3V %s 5.0V %s VPP_PGM %s VPP_VCC %s\n",
-		reg,
-		(reg & TPS2205_VCC3)    ? "off" : "on",
-		(reg & TPS2205_VCC5)    ? "off" : "on",
-		(reg & TPS2205_VPP_PGM) ? "off" : "on",
-		(reg & TPS2205_VPP_VCC) ? "off" : "on" );
-
-	cp->cp_pbdat = reg;
-
-	/*  Wait 500 ms; use this to check for over-current */
-	for (i=0; i<5000; ++i) {
-		if ((cp->cp_pbdat & TPS2205_OC) == 0) {
-			printf ("   *** Overcurrent - Safety shutdown ***\n");
-			cp->cp_pbdat &= ~(TPS2205_SHDN);
-			return (1);
-		}
-		udelay (100);
-	}
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CFG_IMMR;
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
-	/* Shut down */
-	cp->cp_pbdat &= ~(TPS2205_SHDN);
-
-	/* Configure PCMCIA General Control Register */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(10000);
-
-	return (0);
-}
-#endif	/* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("voltage_set: "
-		PCMCIA_BOARD_MSG
-		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	immap = (immap_t *)CFG_IMMR;
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	/*
-	 * Disable PCMCIA buffers (isolate the interface)
-	 * and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(_slot_);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Configure Port C pins for
-	 * 5 Volts Enable and 3 Volts enable,
-	 * Turn all power pins to Hi-Z
-	 */
-	debug ("PCMCIA power OFF\n");
-	cfg_port_B ();	/* Enables switch, but all in Hi-Z */
-
-	reg  = cp->cp_pbdat;
-
-	switch(vcc) {
-	case  0: 			break;	/* Switch off		*/
-	case 33: reg &= ~TPS2205_VCC3;	break;	/* Switch on 3.3V	*/
-	case 50: reg &= ~TPS2205_VCC5;	break;	/* Switch on 5.0V	*/
-	default: 			goto done;
-	}
-
-	/* Checking supported voltages */
-
-	debug ("PIPR: 0x%x --> %s\n",
-		pcmp->pcmc_pipr,
-		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-	cp->cp_pbdat = reg;
-
-#ifdef DEBUG
-    {
-	char *s;
-
-	if ((reg & TPS2205_VCC3) == 0) {
-		s = "at 3.3V";
-	} else if ((reg & TPS2205_VCC5) == 0) {
-		s = "at 5.0V";
-	} else {
-		s = "down";
-	}
-	printf ("PCMCIA powered %s\n", s);
-    }
-#endif
-
-done:
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-		slot+'A');
-	return (0);
-}
-
-static void cfg_port_B (void)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	uint reg;
-
-	immap = (immap_t *)CFG_IMMR;
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/*
-	 * Configure Port B for TPS2205 PC-Card Power-Interface Switch
-	 *
-	 * Switch off all voltages, assert shutdown
-	 */
-	reg  = cp->cp_pbdat;
-	reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
-		TPS2205_VCC3    | TPS2205_VCC5    |	/* VAVCC => Hi-Z */
-		TPS2205_SHDN);				/* enable switch */
-	cp->cp_pbdat = reg;
-
-	cp->cp_pbpar &= ~(TPS2205_INPUTS | TPS2205_OUTPUTS);
-
-	reg = cp->cp_pbdir & ~(TPS2205_INPUTS);
-	cp->cp_pbdir = reg | TPS2205_OUTPUTS;
-
-	debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
-		cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
-}
-
-#endif	/* ICU862 */
-
-
-/* -------------------------------------------------------------------- */
-/* C2MON Boards by TTTech Computertechnik AG				*/
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_C2MON)
-
-#define PCMCIA_BOARD_MSG "C2MON"
-
-static void cfg_ports (void);
-
-static int hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, pipr, mask;
-	ushort sreg;
-	int i;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	immap = (immap_t *)CFG_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
-	cfg_ports ();
-
-	/*
-	 * Configure SIUMCR to enable PCMCIA port B
-	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-	 */
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	 * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
-	 */
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	pipr = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-		pipr,
-		(reg&PCMCIA_VS1(slot))?"n":"ff",
-		(reg&PCMCIA_VS2(slot))?"n":"ff");
-
-	sreg = immap->im_ioport.iop_pcdat;
-	if ((pipr & mask) == mask) {
-		sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1 |	/* VAVPP => Hi-Z */
-			  TPS2211_VCCD1);			/* 5V on	*/
-		sreg &= ~(TPS2211_VCCD0);			/* 3V off	*/
-		puts (" 5.0V card found: ");
-	} else {
-		sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1 |	/* VAVPP => Hi-Z */
-			  TPS2211_VCCD0);			/* 3V on	*/
-		sreg &= ~(TPS2211_VCCD1);			/* 5V off	*/
-		puts (" 3.3V card found: ");
-	}
-
-	debug ("\nPC DAT: %04x -> 3.3V %s 5.0V %s\n",
-		sreg,
-		( (sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) ? "on" : "off",
-		(!(sreg & TPS2211_VCCD0) &&  (sreg & TPS2211_VCCD1)) ? "on" : "off"
-	);
-
-	immap->im_ioport.iop_pcdat = sreg;
-
-	/*  Wait 500 ms; use this to check for over-current */
-	for (i=0; i<5000; ++i) {
-		if ((cp->cp_pbdat & TPS2211_OC) == 0) {
-		    printf ("   *** Overcurrent - Safety shutdown ***\n");
-		    immap->im_ioport.iop_pcdat &= ~(TPS2211_VCCD0|TPS2211_VCCD1);
-		    return (1);
-		}
-		udelay (100);
-	}
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
-	/* Configure PCMCIA General Control Register */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	/* ALl voltages off / Hi-Z */
-	immap->im_ioport.iop_pcdat |= (TPS2211_VPPD0 | TPS2211_VPPD1 |
-				       TPS2211_VCCD0 | TPS2211_VCCD1 );
-
-	udelay(10000);
-
-	return (0);
-}
-#endif	/* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-	ushort sreg;
-
-	debug ("voltage_set: "
-		PCMCIA_BOARD_MSG
-		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	immap = (immap_t *)CFG_IMMR;
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	/*
-	 * Disable PCMCIA buffers (isolate the interface)
-	 * and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(_slot_);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Configure Port C pins for
-	 * 5 Volts Enable and 3 Volts enable,
-	 * Turn all power pins to Hi-Z
-	 */
-	debug ("PCMCIA power OFF\n");
-	cfg_ports ();	/* Enables switch, but all in Hi-Z */
-
-	sreg  = immap->im_ioport.iop_pcdat;
-	sreg |= TPS2211_VPPD0 | TPS2211_VPPD1;		/* VAVPP always Hi-Z */
-
-	switch(vcc) {
-	case  0: 			break;	/* Switch off		*/
-	case 33: sreg |=  TPS2211_VCCD0;	/* Switch on 3.3V	*/
-		 sreg &= ~TPS2211_VCCD1;
-		 			break;
-	case 50: sreg &= ~TPS2211_VCCD0;	/* Switch on 5.0V	*/
-		 sreg |=  TPS2211_VCCD1;
-		 			break;
-	default: 			goto done;
-	}
-
-	/* Checking supported voltages */
-
-	debug ("PIPR: 0x%x --> %s\n",
-		pcmp->pcmc_pipr,
-		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-	immap->im_ioport.iop_pcdat = sreg;
-
-#ifdef DEBUG
-    {
-	char *s;
-
-	if ((sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) {
-		s = "at 3.3V";
-	} else if (!(sreg & TPS2211_VCCD0) &&  (sreg & TPS2211_VCCD1)) {
-		s = "at 5.0V";
-	} else {
-		s = "down";
-	}
-	printf ("PCMCIA powered %s\n", s);
-    }
-#endif
-
-done:
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-		slot+'A');
-	return (0);
-}
-
-static void cfg_ports (void)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	ushort sreg;
-
-	immap = (immap_t *)CFG_IMMR;
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/*
-	 * Configure Port C for TPS2211 PC-Card Power-Interface Switch
-	 *
-	 * Switch off all voltages, assert shutdown
-	 */
-	sreg = immap->im_ioport.iop_pcdat;
-	sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1);	/* VAVPP => Hi-Z */
-	sreg &= ~(TPS2211_VCCD0 | TPS2211_VCCD1);	/* 3V and 5V off */
-	immap->im_ioport.iop_pcdat = sreg;
-
-	immap->im_ioport.iop_pcpar &= ~(TPS2211_OUTPUTS);
-	immap->im_ioport.iop_pcdir |=   TPS2211_OUTPUTS;
-
-	debug ("Set Port C: PAR:     %04x DIR:     %04x DAT:     %04x\n",
-		immap->im_ioport.iop_pcpar,
-		immap->im_ioport.iop_pcdir,
-		immap->im_ioport.iop_pcdat);
-
-	/*
-	 * Configure Port B for TPS2211 PC-Card Power-Interface Switch
-	 *
-	 * Over-Current Input only
-	 */
-	cp->cp_pbpar &= ~(TPS2211_INPUTS);
-	cp->cp_pbdir &= ~(TPS2211_INPUTS);
-
-	debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
-		cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
-}
-
-#endif	/* C2MON */
-
-/* -------------------------------------------------------------------- */
-/* MBX board from Morotola						*/
-/* -------------------------------------------------------------------- */
-
-#if defined( CONFIG_MBX )
-#include <../board/mbx8xx/csr.h>
-
-/* A lot of this has been taken from the RPX code in this file it works from me.
-   I have added the voltage selection for the MBX board. */
-
-/* MBX voltage bit in control register #2 */
-#define CR2_VPP12       ((uchar)0x10)
-#define CR2_VPPVDD      ((uchar)0x20)
-#define CR2_VDD5        ((uchar)0x40)
-#define CR2_VDD3        ((uchar)0x80)
-
-#define PCMCIA_BOARD_MSG "MBX860"
-
-static int voltage_set (int slot, int vcc, int vpp)
-{
-	uchar reg = 0;
-
-	debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		 'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
-
-	switch (vcc) {
-	case 0:
-		break;
-	case 33:
-		reg |= CR2_VDD3;
-		break;
-	case 50:
-		reg |= CR2_VDD5;
-		break;
-	default:
-		return 1;
-	}
-
-	switch (vpp) {
-	case 0:
-		break;
-	case 33:
-	case 50:
-		if (vcc == vpp) {
-			reg |= CR2_VPPVDD;
-		} else {
-			return 1;
-		}
-		break;
-	case 120:
-		reg |= CR2_VPP12;
-		break;
-	default:
-		return 1;
-	}
-
-	/* first, turn off all power */
-	MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
-
-	/* enable new powersettings */
-	MBX_CSR2 |= reg;
-	debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
-
-	return (0);
-}
-
-static int hardware_enable (int slot)
-{
-	volatile immap_t *immap;
-	volatile cpm8xx_t *cp;
-	volatile pcmconf8xx_t *pcmp;
-	volatile sysconf8xx_t *sysp;
-	uint reg, mask;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
-				  'A' + slot);
-
-	udelay (10000);
-
-	immap = (immap_t *) CFG_IMMR;
-	sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
-	pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
-	cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;	/* active low  */
-	PCMCIA_PGCRX (_slot_) = reg;
-	udelay (500);
-
-	/* remove all power */
-	voltage_set (slot, 0, 0);
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-#ifndef CONFIG_HMI10
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-#else
-	if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
-#endif	/* CONFIG_HMI10 */
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	 * Power On.
-	 */
-	mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
-	reg = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
-		  (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
-		  (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
-
-	if ((reg & mask) == mask) {
-		voltage_set (_slot_, 50, 0);
-		printf (" 5.0V card found: ");
-	} else {
-		voltage_set (_slot_, 33, 0);
-		printf (" 3.3V card found: ");
-	}
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg = PCMCIA_PGCRX (_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;	/* active low  */
-	PCMCIA_PGCRX (_slot_) = reg;
-
-	udelay (250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable (int slot)
-{
-	return 0;	/* No hardware to disable */
-}
-#endif /* CFG_CMD_PCMCIA */
-#endif /* CONFIG_MBX */
-/* -------------------------------------------------------------------- */
-/* R360MPI Board							*/
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_R360MPI)
-
-#define PCMCIA_BOARD_MSG "R360MPI"
-
-
-static int hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, mask;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	immap = (immap_t *)CFG_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/*
-	 * Configure SIUMCR to enable PCMCIA port B
-	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-	 */
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Configure Ports A, B & C pins for
-	 * 5 Volts Enable and 3 Volts enable
-	 */
-	immap->im_ioport.iop_pcpar &= ~(0x0400);
-	immap->im_ioport.iop_pcso  &= ~(0x0400);/*
-	immap->im_ioport.iop_pcdir |= 0x0400;*/
-
-	immap->im_ioport.iop_papar &= ~(0x0200);/*
-	immap->im_ioport.iop_padir |= 0x0200;*/
-#if 0
-	immap->im_ioport.iop_pbpar &= ~(0xC000);
-	immap->im_ioport.iop_pbdir &= ~(0xC000);
-#endif
-	/* remove all power */
-
-	immap->im_ioport.iop_pcdat |= 0x0400;
-	immap->im_ioport.iop_padat |= 0x0200;
-
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	 * Power On.
-	 */
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	reg  = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-		reg,
-		(reg&PCMCIA_VS1(slot))?"n":"ff",
-		(reg&PCMCIA_VS2(slot))?"n":"ff");
-	if ((reg & mask) == mask) {
-		immap->im_ioport.iop_pcdat &= ~(0x4000);
-		puts (" 5.0V card found: ");
-	} else {
-		immap->im_ioport.iop_padat &= ~(0x0002);
-		puts (" 3.3V card found: ");
-	}
-	immap->im_ioport.iop_pcdir |= 0x0400;
-	immap->im_ioport.iop_padir |= 0x0200;
-#if 0
-	/*  VCC switch error flag, PCMCIA slot INPACK_ pin */
-	cp->cp_pbdir &= ~(0x0020 | 0x0010);
-	cp->cp_pbpar &= ~(0x0020 | 0x0010);
-	udelay(500000);
-#endif
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
-	/* remove all power */
-	immap->im_ioport.iop_pcdat |= 0x0400;
-	immap->im_ioport.iop_padat |= 0x0200;
-
-	/* Configure PCMCIA General Control Register */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(10000);
-
-	return (0);
-}
-#endif	/* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("voltage_set: "
-		PCMCIA_BOARD_MSG
-		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	/*
-	 * Disable PCMCIA buffers (isolate the interface)
-	 * and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(_slot_);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Configure Ports A & C pins for
-	 * 5 Volts Enable and 3 Volts enable,
-	 * Turn off all power
-	 */
-	debug ("PCMCIA power OFF\n");
-	immap->im_ioport.iop_pcpar &= ~(0x0400);
-	immap->im_ioport.iop_pcso  &= ~(0x0400);/*
-	immap->im_ioport.iop_pcdir |= 0x0400;*/
-
-	immap->im_ioport.iop_papar &= ~(0x0200);/*
-	immap->im_ioport.iop_padir |= 0x0200;*/
-
-	immap->im_ioport.iop_pcdat |= 0x0400;
-	immap->im_ioport.iop_padat |= 0x0200;
-
-	reg = 0;
-	switch(vcc) {
-	case  0: 		break;
-	case 33: reg |= 0x0200;	break;
-	case 50: reg |= 0x0400;	break;
-	default: 		goto done;
-	}
-
-	/* Checking supported voltages */
-
-	debug ("PIPR: 0x%x --> %s\n",
-		pcmp->pcmc_pipr,
-		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-	if (reg & 0x0200)
-		immap->im_ioport.iop_pcdat &= !reg;
-	if (reg & 0x0400)
-		immap->im_ioport.iop_padat &= !reg;
-	immap->im_ioport.iop_pcdir |= 0x0200;
-	immap->im_ioport.iop_padir |= 0x0400;
-	if (reg) {
-		debug ("PCMCIA powered at %sV\n",
-			(reg&0x0400) ? "5.0" : "3.3");
-	} else {
-		debug ("PCMCIA powered down\n");
-	}
-
-done:
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-		slot+'A');
-	return (0);
-}
-
-#endif	/* R360MPI */
-
-/* -------------------------------------------------------------------- */
-/* KUP4K and KUP4X Boards								*/
-/* -------------------------------------------------------------------- */
-#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
-
-#define PCMCIA_BOARD_MSG "KUP"
-
-#define KUP4K_PCMCIA_B_3V3 (0x00020000)
-
-static int hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, mask;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	immap = (immap_t *)CFG_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/*
-	 * Configure SIUMCR to enable PCMCIA port B
-	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-	 */
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(slot);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(slot) = reg;
-	udelay(2500);
-
-	/*
-	 * Configure Port B pins for
-	 * 3 Volts enable
-	 */
-	if (slot) { /* Slot A is built-in */
-		cp->cp_pbdir |=  KUP4K_PCMCIA_B_3V3;
-		cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
-		/* remove all power */
-		cp->cp_pbdat |=  KUP4K_PCMCIA_B_3V3; /* active low */
-	}
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	 * Power On.
-	 */
-	printf("%s  Slot %c:", slot ? "" : "\n", 'A' + slot);
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	reg  = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-		reg,
-		(reg&PCMCIA_VS1(slot))?"n":"ff",
-		(reg&PCMCIA_VS2(slot))?"n":"ff");
-	if ((reg & mask) == mask) {
-		puts (" 5.0V card found: NOT SUPPORTED !!!\n");
-	} else {
-		if(slot)
-			cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
-		puts (" 3.3V card found: ");
-	}
-#if 0
-	/*  VCC switch error flag, PCMCIA slot INPACK_ pin */
-	cp->cp_pbdir &= ~(0x0020 | 0x0010);
-	cp->cp_pbpar &= ~(0x0020 | 0x0010);
-	udelay(500000);
-#endif
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(slot);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(slot) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/* remove all power */
-	if (slot)
-		cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3;
-
-	/* Configure PCMCIA General Control Register */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(slot) = reg;
-
-	udelay(10000);
-
-	return (0);
-}
-#endif	/* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("voltage_set: "	\
-		PCMCIA_BOARD_MSG	\
-		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	if (!slot) /* Slot A is not configurable */
-		return 0;
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/*
-	 * Disable PCMCIA buffers (isolate the interface)
-	 * and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(slot);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(slot) = reg;
-	udelay(500);
-
-	debug ("PCMCIA power OFF\n");
-	/*
-	 * Configure Port B pins for
-	 * 3 Volts enable
-	 */
-	cp->cp_pbdir |=  KUP4K_PCMCIA_B_3V3;
-	cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
-	/* remove all power */
-	cp->cp_pbdat |=  KUP4K_PCMCIA_B_3V3; /* active low */
-
-	switch(vcc) {
-	case  0: 		break;
-	case 33:
-		cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
-		debug ("PCMCIA powered at 3.3V\n");
-		break;
-	case 50:
-		debug ("PCMCIA: 5Volt vcc not supported\n");
-		break;
-	default:
-		puts("PCMCIA: vcc not supported");
-		break;
-	}
-	udelay(10000);
-	/* Checking supported voltages */
-
-	debug ("PIPR: 0x%x --> %s\n",
-		pcmp->pcmc_pipr,
-		   (pcmp->pcmc_pipr & (0x80000000 >> (slot << 4)))
-			? "only 5 V --> NOT SUPPORTED"
-			: "can do 3.3V");
-
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(slot);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(slot) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-		slot+'A');
-	return (0);
-}
-
-#endif	/* KUP4K || KUP4X */
-
-
-/* -------------------------------------------------------------------- */
-/* End of Board Specific Stuff						*/
-/* -------------------------------------------------------------------- */
-
-
-/* -------------------------------------------------------------------- */
-/* MPC8xx Specific Stuff - should go to MPC8xx directory		*/
-/* -------------------------------------------------------------------- */
-
-/*
- * Search this table to see if the windowsize is
- * supported...
- */
-
-#define M8XX_SIZES_NO 32
-
-static const u_int m8xx_size_to_gray[M8XX_SIZES_NO] =
-{ 0x00000001, 0x00000002, 0x00000008, 0x00000004,
-  0x00000080, 0x00000040, 0x00000010, 0x00000020,
-  0x00008000, 0x00004000, 0x00001000, 0x00002000,
-  0x00000100, 0x00000200, 0x00000800, 0x00000400,
-
-  0x0fffffff, 0xffffffff, 0xffffffff, 0xffffffff,
-  0x01000000, 0x02000000, 0xffffffff, 0x04000000,
-  0x00010000, 0x00020000, 0x00080000, 0x00040000,
-  0x00800000, 0x00400000, 0x00100000, 0x00200000 };
-
-
-/* -------------------------------------------------------------------- */
-
-#if ( ! defined(CONFIG_I82365) && ! defined(CONFIG_PXA_PCMCIA) )
-
-static u_int m8xx_get_graycode(u_int size)
-{
-	u_int k;
-
-	for (k = 0; k < M8XX_SIZES_NO; k++) {
-		if(m8xx_size_to_gray[k] == size)
-			break;
-	}
-
-	if((k == M8XX_SIZES_NO) || (m8xx_size_to_gray[k] == -1))
-		k = -1;
-
-	return k;
-}
-
-#endif	/* CONFIG_I82365 */
-
-/* -------------------------------------------------------------------- */
-
-#if 0
-static u_int m8xx_get_speed(u_int ns, u_int is_io)
-{
-	u_int reg, clocks, psst, psl, psht;
-
-	if(!ns) {
-
-		/*
-		 * We get called with IO maps setup to 0ns
-		 * if not specified by the user.
-		 * They should be 255ns.
-		 */
-
-		if(is_io)
-			ns = 255;
-		else
-			ns = 100;  /* fast memory if 0 */
-	}
-
-	/*
-	 * In PSST, PSL, PSHT fields we tell the controller
-	 * timing parameters in CLKOUT clock cycles.
-	 * CLKOUT is the same as GCLK2_50.
-	 */
-
-/* how we want to adjust the timing - in percent */
-
-#define ADJ 180 /* 80 % longer accesstime - to be sure */
-
-	clocks = ((M8XX_BUSFREQ / 1000) * ns) / 1000;
-	clocks = (clocks * ADJ) / (100*1000);
-
-	if(clocks >= PCMCIA_BMT_LIMIT) {
-		DEBUG(0, "Max access time limit reached\n");
-		clocks = PCMCIA_BMT_LIMIT-1;
-	}
-
-	psst = clocks / 7;          /* setup time */
-	psht = clocks / 7;          /* hold time */
-	psl  = (clocks * 5) / 7;    /* strobe length */
-
-	psst += clocks - (psst + psht + psl);
-
-	reg =  psst << 12;
-	reg |= psl  << 7;
-	reg |= psht << 16;
-
-	return reg;
-}
-#endif
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-static void print_funcid (int func)
-{
-	puts (indent);
-	switch (func) {
-	case CISTPL_FUNCID_MULTI:
-		puts (" Multi-Function");
-		break;
-	case CISTPL_FUNCID_MEMORY:
-		puts (" Memory");
-		break;
-	case CISTPL_FUNCID_SERIAL:
-		puts (" Serial Port");
-		break;
-	case CISTPL_FUNCID_PARALLEL:
-		puts (" Parallel Port");
-		break;
-	case CISTPL_FUNCID_FIXED:
-		puts (" Fixed Disk");
-		break;
-	case CISTPL_FUNCID_VIDEO:
-		puts (" Video Adapter");
-		break;
-	case CISTPL_FUNCID_NETWORK:
-		puts (" Network Adapter");
-		break;
-	case CISTPL_FUNCID_AIMS:
-		puts (" AIMS Card");
-		break;
-	case CISTPL_FUNCID_SCSI:
-		puts (" SCSI Adapter");
-		break;
-	default:
-		puts (" Unknown");
-		break;
 	}
 	puts (" Card\n");
 }
-#endif	/* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
 
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
 static void print_fixed (volatile uchar *p)
 {
 	if (p == NULL)
@@ -2804,16 +169,16 @@ static void print_fixed (volatile uchar *p)
 	puts(indent);
 
 	switch (*p) {
-	case CISTPL_FUNCE_IDE_IFACE:
-	    {   uchar iface = *(p+2);
+		case CISTPL_FUNCE_IDE_IFACE:
+		{   uchar iface = *(p+2);
 
 		puts ((iface == CISTPL_IDE_INTERFACE) ? " IDE" : " unknown");
 		puts (" interface ");
 		break;
-	    }
-	case CISTPL_FUNCE_IDE_MASTER:
-	case CISTPL_FUNCE_IDE_SLAVE:
-	    {   uchar f1 = *(p+2);
+		}
+		case CISTPL_FUNCE_IDE_MASTER:
+		case CISTPL_FUNCE_IDE_SLAVE:
+		{   uchar f1 = *(p+2);
 		uchar f2 = *(p+4);
 
 		puts ((f1 & CISTPL_IDE_SILICON) ? " [silicon]" : " [rotating]");
@@ -2845,23 +210,10 @@ static void print_fixed (volatile uchar *p)
 			puts (" [IOis16]");
 
 		break;
-	    }
+		}
 	}
 	putc ('\n');
 }
-#endif	/* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_PXA_PCMCIA)
-
-#define MAX_IDENT_CHARS		64
-#define	MAX_IDENT_FIELDS	4
-
-static uchar *known_cards[] = {
-	(uchar *)"ARGOSY PnPIDE D5",
-	NULL
-};
 
 static int identify  (volatile uchar *p)
 {
@@ -2913,576 +265,101 @@ static int identify  (volatile uchar *p)
 
 	return (0);	/* don't know */
 }
-#endif	/* CONFIG_IDE_8xx_PCCARD */
-
-/* -------------------------------------------------------------------- */
-/* NETTA board by Intracom S.A.						*/
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_NETTA)
-
-/* some sane bit macros */
-#define _BD(_b)				(1U << (31-(_b)))
-#define _BDR(_l, _h)			(((((1U << (31-(_l))) - 1) << 1) | 1) & ~((1U << (31-(_h))) - 1))
-
-#define _BW(_b)				(1U << (15-(_b)))
-#define _BWR(_l, _h)			(((((1U << (15-(_l))) - 1) << 1) | 1) & ~((1U << (15-(_h))) - 1))
-
-#define _BB(_b)				(1U << (7-(_b)))
-#define _BBR(_l, _h)			(((((1U << (7-(_l))) - 1) << 1) | 1) & ~((1U << (7-(_h))) - 1))
-
-#define _B(_b)				_BD(_b)
-#define _BR(_l, _h)			_BDR(_l, _h)
 
-#define PCMCIA_BOARD_MSG "NETTA"
-
-static const unsigned short vppd_masks[2] = { _BW(14), _BW(15) };
-
-static void cfg_vppd(int no)
-{
-	volatile immap_t *immap = (immap_t *)CFG_IMMR;
-	unsigned short mask;
-
-	if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
-		return;
-
-	mask = vppd_masks[no];
-
-	immap->im_ioport.iop_papar &= ~mask;
-	immap->im_ioport.iop_paodr &= ~mask;
-	immap->im_ioport.iop_padir |=  mask;
-}
-
-static void set_vppd(int no, int what)
+int check_ide_device (int slot)
 {
-	volatile immap_t *immap = (immap_t *)CFG_IMMR;
-	unsigned short mask;
-
-	if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
-		return;
-
-	mask = vppd_masks[no];
-
-	if (what)
-		immap->im_ioport.iop_padat |= mask;
-	else
-		immap->im_ioport.iop_padat &= ~mask;
-}
-
-static const unsigned short vccd_masks[2] = { _BW(10), _BW(6) };
-
-static void cfg_vccd(int no)
-{
-	volatile immap_t *immap = (immap_t *)CFG_IMMR;
-	unsigned short mask;
-
-	if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
-		return;
-
-	mask = vccd_masks[no];
-
-	immap->im_ioport.iop_papar &= ~mask;
-	immap->im_ioport.iop_paodr &= ~mask;
-	immap->im_ioport.iop_padir |=  mask;
-}
-
-static void set_vccd(int no, int what)
-{
-	volatile immap_t *immap = (immap_t *)CFG_IMMR;
-	unsigned short mask;
-
-	if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
-		return;
-
-	mask = vccd_masks[no];
-
-	if (what)
-		immap->im_ioport.iop_padat |= mask;
-	else
-		immap->im_ioport.iop_padat &= ~mask;
-}
-
-static const unsigned short oc_mask = _BW(8);
-
-static void cfg_oc(void)
-{
-	volatile immap_t *immap = (immap_t *)CFG_IMMR;
-	unsigned short mask = oc_mask;
-
-	immap->im_ioport.iop_pcdir &= ~mask;
-	immap->im_ioport.iop_pcso  &= ~mask;
-	immap->im_ioport.iop_pcint &= ~mask;
-	immap->im_ioport.iop_pcpar &= ~mask;
-}
-
-static int get_oc(void)
-{
-	volatile immap_t *immap = (immap_t *)CFG_IMMR;
-	unsigned short mask = oc_mask;
-	int what;
-
-	what = !!(immap->im_ioport.iop_pcdat & mask);;
-	return what;
-}
-
-static const unsigned short shdn_mask = _BW(12);
-
-static void cfg_shdn(void)
-{
-	volatile immap_t *immap = (immap_t *)CFG_IMMR;
-	unsigned short mask;
-
-	mask = shdn_mask;
-
-	immap->im_ioport.iop_papar &= ~mask;
-	immap->im_ioport.iop_paodr &= ~mask;
-	immap->im_ioport.iop_padir |=  mask;
-}
-
-static void set_shdn(int what)
-{
-	volatile immap_t *immap = (immap_t *)CFG_IMMR;
-	unsigned short mask;
-
-	mask = shdn_mask;
-
-	if (what)
-		immap->im_ioport.iop_padat |= mask;
-	else
-		immap->im_ioport.iop_padat &= ~mask;
-}
-
-static void cfg_ports (void);
-
-static int hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, pipr, mask;
+	volatile uchar *ident = NULL;
+	volatile uchar *feature_p[MAX_FEATURES];
+	volatile uchar *p, *start, *addr;
+	int n_features = 0;
+	uchar func_id = ~0;
+	uchar code, len;
+	ushort config_base = 0;
+	int found = 0;
 	int i;
 
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	immap = (immap_t *)CFG_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
-	cfg_ports ();
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+	addr = (volatile uchar *)(CFG_PCMCIA_MEM_ADDR +
+				  CFG_PCMCIA_MEM_SIZE * (slot * 4));
+	debug ("PCMCIA MEM: %08lX\n", (ulong)addr);
 
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
+	start = p = (volatile uchar *) addr;
 
-	udelay(500);
+	while ((p - start) < MAX_TUPEL_SZ) {
 
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
+		code = *p; p += 2;
 
-	/*
-	 * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
-	 */
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	pipr = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-		pipr,
-		(reg&PCMCIA_VS1(slot))?"n":"ff",
-		(reg&PCMCIA_VS2(slot))?"n":"ff");
+		if (code == 0xFF) { /* End of chain */
+			break;
+		}
 
-	if ((pipr & mask) == mask) {
-		set_vppd(0, 1); set_vppd(1, 1); 		/* VAVPP => Hi-Z */
-		set_vccd(0, 0); set_vccd(1, 1); 		/* 5V on, 3V off */
-		puts (" 5.0V card found: ");
-	} else {
-		set_vppd(0, 1); set_vppd(1, 1); 		/* VAVPP => Hi-Z */
-		set_vccd(0, 1); set_vccd(1, 0); 		/* 5V off, 3V on */
-		puts (" 3.3V card found: ");
-	}
+		len = *p; p += 2;
+#if defined(DEBUG) && (DEBUG > 1)
+		{ volatile uchar *q = p;
+			printf ("\nTuple code %02x  length %d\n\tData:",
+				code, len);
 
-	/*  Wait 500 ms; use this to check for over-current */
-	for (i=0; i<5000; ++i) {
-		if (!get_oc()) {
-			printf ("   *** Overcurrent - Safety shutdown ***\n");
-			set_vccd(0, 0); set_vccd(1, 0); 		/* VAVPP => Hi-Z */
-			return (1);
+			for (i = 0; i < len; ++i) {
+				printf (" %02x", *q);
+				q+= 2;
+			}
 		}
-		udelay (100);
+#endif	/* DEBUG */
+		switch (code) {
+		case CISTPL_VERS_1:
+			ident = p + 4;
+			break;
+		case CISTPL_FUNCID:
+			/* Fix for broken SanDisk which may have 0x80 bit set */
+			func_id = *p & 0x7F;
+			break;
+		case CISTPL_FUNCE:
+			if (n_features < MAX_FEATURES)
+				feature_p[n_features++] = p;
+			break;
+		case CISTPL_CONFIG:
+			config_base = (*(p+6) << 8) + (*(p+4));
+			debug ("\n## Config_base = %04x ###\n", config_base);
+		default:
+			break;
+		}
+		p += 2 * len;
 	}
 
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
-	/* Configure PCMCIA General Control Register */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	/* All voltages off / Hi-Z */
-			set_vppd(0, 1); set_vppd(1, 1);
-	set_vccd(0, 1); set_vccd(1, 1);
-
-	udelay(10000);
-
-	return (0);
-}
-#endif	/* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-	ushort sreg;
-
-	debug ("voltage_set: "
-		PCMCIA_BOARD_MSG
-		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	immap = (immap_t *)CFG_IMMR;
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	/*
-	 * Disable PCMCIA buffers (isolate the interface)
-	 * and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(_slot_);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Configure Port C pins for
-	 * 5 Volts Enable and 3 Volts enable,
-	 * Turn all power pins to Hi-Z
-	 */
-	debug ("PCMCIA power OFF\n");
-	cfg_ports ();	/* Enables switch, but all in Hi-Z */
-
-	sreg  = immap->im_ioport.iop_pcdat;
-	set_vppd(0, 1); set_vppd(1, 1);
-
-	switch(vcc) {
-	case  0:
-		break;	/* Switch off		*/
-
-	case 33:
-		set_vccd(0, 1); set_vccd(1, 0);
-		break;
+	found = identify (ident);
 
-	case 50:
-		set_vccd(0, 0); set_vccd(1, 1);
-		break;
+	if (func_id != ((uchar)~0)) {
+		print_funcid (func_id);
 
-	default:
-		goto done;
+		if (func_id == CISTPL_FUNCID_FIXED)
+			found = 1;
+		else
+			return (1);	/* no disk drive */
 	}
 
-	/* Checking supported voltages */
-
-	debug ("PIPR: 0x%x --> %s\n",
-		pcmp->pcmc_pipr,
-		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-done:
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-		slot+'A');
-	return (0);
-}
-
-static void cfg_ports (void)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-
-	immap = (immap_t *)CFG_IMMR;
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-
-	cfg_vppd(0); cfg_vppd(1);	/* VPPD0,VPPD1 VAVPP => Hi-Z */
-	cfg_vccd(0); cfg_vccd(1);	/* 3V and 5V off */
-	cfg_shdn();
-	cfg_oc();
-
-	/*
-	 * Configure Port A for TPS2211 PC-Card Power-Interface Switch
-	 *
-	 * Switch off all voltages, assert shutdown
-	 */
-	set_vppd(0, 1); set_vppd(1, 1);
-	set_vccd(0, 0); set_vccd(1, 0);
-	set_shdn(1);
-
-	udelay(100000);
-}
-
-#endif	/* NETTA */
-
-
-/* -------------------------------------------------------------------- */
-/* UC100 Boards                                          		*/
-/* -------------------------------------------------------------------- */
-
-#if defined(CONFIG_UC100)
-
-#define PCMCIA_BOARD_MSG "UC100"
-
-/*
- * Remark: don't turn off OE "__MY_PCMCIA_GCRX_CXOE" on UC100 board.
- *         This leads to board-hangup! (sr, 8 Dez. 2004)
- */
-
-static void cfg_ports (void);
-
-static int hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, mask;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	immap = (immap_t *)CFG_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
-
-	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
-	cfg_ports ();
-
-	/*
-	 * Configure SIUMCR to enable PCMCIA port B
-	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-	 */
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
-	/*
-	 * Disable interrupts, DMA, and PCMCIA buffers
-	 * (isolate the interface) and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Make sure there is a card in the slot, then configure the interface.
-	 */
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-		__LINE__,__FUNCTION__,
-		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
+	for (i=0; i<n_features; ++i) {
+		print_fixed (feature_p[i]);
 	}
 
-	/*
-	 * Power On.
-	 */
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	reg  = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-		reg,
-		(reg&PCMCIA_VS1(slot))?"n":"ff",
-		(reg&PCMCIA_VS2(slot))?"n":"ff");
-	if ((reg & mask) == mask) {
-		puts (" 5.0V card found: ");
-	} else {
-		puts (" 3.3V card found: ");
+	if (!found) {
+		printf ("unknown card type\n");
+		return (1);
 	}
 
-	/*  switch VCC on */
-	immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */
-
-	udelay(10000);
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-static int hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-
-	/* switch VCC off */
-	immap->im_ioport.iop_padat &= ~0x8000; /* power disable 3.3V */
-
-	/* Configure PCMCIA General Control Register */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(10000);
-
-	return (0);
-}
-#endif	/* CFG_CMD_PCMCIA */
-
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("voltage_set: "
-		PCMCIA_BOARD_MSG
-		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	immap = (immap_t *)CFG_IMMR;
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
-	/*
-	 * Disable PCMCIA buffers (isolate the interface)
-	 * and assert RESET signal
-	 */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(_slot_);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	 * Configure Port C pins for
-	 * 5 Volts Enable and 3 Volts enable,
-	 * Turn all power pins to Hi-Z
-	 */
-	debug ("PCMCIA power OFF\n");
-	cfg_ports ();	/* Enables switch, but all in Hi-Z */
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
+	ide_devices_found |= (1 << slot);
 
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-		slot+'A');
+#if CONFIG_CPC45
+#else
+	/* set I/O area in config reg -> only valid for ARGOSY D5!!! */
+	*((uchar *)(addr + config_base)) = 1;
+#endif
+#if 0
+	printf("\n## Config_base = %04x ###\n", config_base);
+	printf("Configuration Option Register: %02x @ %x\n", readb(addr + config_base), addr + config_base);
+	printf("Card Configuration and Status Register: %02x\n", readb(addr + config_base + 2));
+	printf("Pin Replacement Register Register: %02x\n", readb(addr + config_base + 4));
+	printf("Socket and Copy Register: %02x\n", readb(addr + config_base + 6));
+#endif
 	return (0);
 }
 
-static void cfg_ports (void)
-{
-	volatile immap_t	*immap;
-
-	immap = (immap_t *)CFG_IMMR;
-
-	/*
-	 * Configure Port A for MAX1602 PC-Card Power-Interface Switch
-	 */
-	immap->im_ioport.iop_padat &= ~0x8000;	/* set port x output to low */
-	immap->im_ioport.iop_padir |= 0x8000;	/* enable port x as output */
-
-	debug ("Set Port A: PAR: %08x DIR: %08x DAT: %08x\n",
-	       immap->im_ioport.iop_papar, immap->im_ioport.iop_padir,
-	       immap->im_ioport.iop_padat);
-}
-
-#endif	/* UC100 */
-
-
-/* -------------------------------------------------------------------- */
-
-#endif /* CFG_CMD_PCMCIA || (CFG_CMD_IDE && CONFIG_IDE_8xx_PCCARD) */
-
-/**************************************************/
-
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
-U_BOOT_CMD(
-	pinit,	2,	1,	do_pinit,
-	"pinit   - PCMCIA sub-system\n",
-	"on  - power on PCMCIA socket\n"
-	"pinit off - power off PCMCIA socket\n"
-);
-#endif
+#endif	/* CHECK_IDE_DEVICE */