mpc85xx: Add eSDHC support for MPC8569E-MDS boards

eSDHC is mutually exlusive with UART0 (in 4-bits mode) and I2C2
(in 1-bit mode). When eSDHC is used, we should switch u-boot console to
UART1, and make the proper device-tree fixups.

Because of an erratum in prototype boards it is impossible to use eSDHC
without disabling UART0 (which makes it quite easy to 'brick' the board
by simply issung 'setenv hwconfig esdhc', and not able to interact with
U-Boot anylonger).

So, but default we assume that the board is a prototype, which is a most
safe assumption. There is no way to determine board revision from a
register, so we use hwconfig.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

2 files changed, 118 insertions, 1 deletions

diff --git a/board/freescale/mpc8569mds/bcsr.h b/board/freescale/mpc8569mds/bcsr.h
index c4738d7343..2ed57d8527 100644
--- a/board/freescale/mpc8569mds/bcsr.h
+++ b/board/freescale/mpc8569mds/bcsr.h
@@ -33,7 +33,8 @@
 #define BCSR6_UPC1_POS_EN	0x40
 #define BCSR6_UPC1_ADDR_EN	0x20
 #define BCSR6_UPC1_DEV2		0x10
-#define BCSR6_SD_ENABLE         0x04
+#define BCSR6_SD_CARD_1BIT	0x08
+#define BCSR6_SD_CARD_4BITS	0x04
 #define BCSR6_TDM2G_EN		0x02
 #define BCSR6_UCC7_RMII_EN	0x01
 
diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c
index cc8873117e..2d07922161 100644
--- a/board/freescale/mpc8569mds/mpc8569mds.c
+++ b/board/freescale/mpc8569mds/mpc8569mds.c
@@ -23,6 +23,7 @@
  */
 
 #include <common.h>
+#include <hwconfig.h>
 #include <pci.h>
 #include <asm/processor.h>
 #include <asm/mmu.h>
@@ -35,6 +36,7 @@
 #include <ioports.h>
 #include <libfdt.h>
 #include <fdt_support.h>
+#include <fsl_esdhc.h>
 
 #include "bcsr.h"
 
@@ -303,6 +305,119 @@ local_bus_init(void)
 	out_be32(&lbc->lcrr, (u32)in_be32(&lbc->lcrr)| 0x00030000);
 }
 
+#ifdef CONFIG_FSL_ESDHC
+
+/*
+ * Because of an erratum in prototype boards it is impossible to use eSDHC
+ * without disabling UART0 (which makes it quite easy to 'brick' the board
+ * by simply issung 'setenv hwconfig esdhc', and not able to interact with
+ * U-Boot anylonger).
+ *
+ * So, but default we assume that the board is a prototype, which is a most
+ * safe assumption. There is no way to determine board revision from a
+ * register, so we use hwconfig.
+ */
+
+static int prototype_board(void)
+{
+	if (hwconfig_subarg("board", "rev", NULL))
+		return hwconfig_subarg_cmp("board", "rev", "prototype");
+	return 1;
+}
+
+static int esdhc_disables_uart0(void)
+{
+	return prototype_board() ||
+	       hwconfig_subarg_cmp("esdhc", "mode", "4-bits");
+}
+
+int board_mmc_init(bd_t *bd)
+{
+	struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+	u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE;
+	u8 bcsr6 = BCSR6_SD_CARD_1BIT;
+
+	if (!hwconfig("esdhc"))
+		return 0;
+
+	printf("Enabling eSDHC...\n"
+	       "  For eSDHC to function, I2C2 ");
+	if (esdhc_disables_uart0()) {
+		printf("and UART0 should be disabled.\n");
+		printf("  Redirecting stderr, stdout and stdin to UART1...\n");
+		console_assign(stderr, "eserial1");
+		console_assign(stdout, "eserial1");
+		console_assign(stdin, "eserial1");
+		printf("Switched to UART1 (initial log has been printed to "
+		       "UART0).\n");
+		bcsr6 |= BCSR6_SD_CARD_4BITS;
+	} else {
+		printf("should be disabled.\n");
+	}
+
+	/* Assign I2C2 signals to eSDHC. */
+	clrsetbits_be32(&gur->plppar1, PLPPAR1_I2C_BIT_MASK,
+				       PLPPAR1_ESDHC_VAL);
+	clrsetbits_be32(&gur->plpdir1, PLPDIR1_I2C_BIT_MASK,
+				       PLPDIR1_ESDHC_VAL);
+
+	/* Mux I2C2 (and optionally UART0) signals to eSDHC. */
+	setbits_8(&bcsr[6], bcsr6);
+
+	return fsl_esdhc_mmc_init(bd);
+}
+
+static void fdt_board_fixup_esdhc(void *blob, bd_t *bd)
+{
+	const char *status = "disabled";
+	int off;
+	int err;
+
+	if (!hwconfig("esdhc"))
+		return;
+
+	if (!esdhc_disables_uart0())
+		goto disable_i2c2;
+
+	off = fdt_path_offset(blob, "serial0");
+	if (off < 0) {
+		printf("WARNING: could not find serial0 alias: %s.\n",
+			fdt_strerror(off));
+		goto disable_i2c2;
+	}
+
+	err = fdt_setprop(blob, off, "status", status, strlen(status) + 1);
+	if (err) {
+		printf("WARNING: could not set status for serial0: %s.\n",
+			fdt_strerror(err));
+		return;
+	}
+
+disable_i2c2:
+	off = -1;
+	while (1) {
+		const u32 *idx;
+		int len;
+
+		off = fdt_node_offset_by_compatible(blob, off, "fsl-i2c");
+		if (off < 0)
+			break;
+
+		idx = fdt_getprop(blob, off, "cell-index", &len);
+		if (!idx || len != sizeof(*idx))
+			continue;
+
+		if (*idx == 1) {
+			fdt_setprop(blob, off, "status", status,
+				    strlen(status) + 1);
+			break;
+		}
+	}
+}
+#else
+static inline void fdt_board_fixup_esdhc(void *blob, bd_t *bd) {}
+#endif
+
 #ifdef CONFIG_PCIE1
 static struct pci_controller pcie1_hose;
 #endif  /* CONFIG_PCIE1 */
@@ -444,5 +559,6 @@ void ft_board_setup(void *blob, bd_t *bd)
 #ifdef CONFIG_PCIE1
 	ft_fsl_pci_setup(blob, "pci1", &pcie1_hose);
 #endif
+	fdt_board_fixup_esdhc(blob, bd);
 }
 #endif