arm: mvebu: theadorable: Add StratixV FPGA programming support

This patch adds support for Altera StratixV bitstream programming. 2 FPGAs
are connected to the SPI busses. This patch uses board specific write
code to program the bitstream via SPI direct write mode.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>

8 files changed, 234 insertions, 2 deletions

diff --git a/arch/arm/dts/armada-xp-theadorable.dts b/arch/arm/dts/armada-xp-theadorable.dts
index cf1be2a3d4..7087ccfc2f 100644
--- a/arch/arm/dts/armada-xp-theadorable.dts
+++ b/arch/arm/dts/armada-xp-theadorable.dts
@@ -69,6 +69,7 @@
 
 	aliases {
 		spi0 = &spi0;
+		spi1 = &spi1;
 		ethernet0 = &eth0;
 	};
 
@@ -137,6 +138,26 @@
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <27777777>;
 				};
+
+				fpga@1 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "spi-generic-device";
+					reg = <1>; /* Chip select 1 */
+					spi-max-frequency = <27777777>;
+				};
+			};
+
+			spi1: spi@10680 {
+				status = "okay";
+
+				fpga@2 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "spi-generic-device";
+					reg = <2>; /* Chip select 2 */
+					spi-max-frequency = <27777777>;
+				};
 			};
 		};
 	};
diff --git a/board/theadorable/Makefile b/board/theadorable/Makefile
index 9d5b39e696..ef5a519ada 100644
--- a/board/theadorable/Makefile
+++ b/board/theadorable/Makefile
@@ -5,3 +5,4 @@
 #
 
 obj-y	:= theadorable.o
+obj-y	+= fpga.o
diff --git a/board/theadorable/fpga.c b/board/theadorable/fpga.c
new file mode 100644
index 0000000000..6f068c38ad
--- /dev/null
+++ b/board/theadorable/fpga.c
@@ -0,0 +1,179 @@
+/*
+ * Copyright (C) 2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <altera.h>
+#include <errno.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <asm/arch-mvebu/spi.h>
+#include "theadorable.h"
+
+/*
+ * FPGA programming support
+ */
+static int fpga_pre_fn(int cookie)
+{
+	int gpio_config = COOKIE2CONFIG(cookie);
+	int gpio_done = COOKIE2DONE(cookie);
+	int ret;
+
+	debug("%s (%d): cookie=%08x gpio_config=%d gpio_done=%d\n",
+	      __func__, __LINE__, cookie, gpio_config, gpio_done);
+
+	/* Configure config pin */
+	/* Set to output */
+	ret = gpio_request(gpio_config, "CONFIG");
+	if (ret < 0)
+		return ret;
+	gpio_direction_output(gpio_config, 1);
+
+	/* Configure done pin */
+	/* Set to input */
+	ret = gpio_request(gpio_done, "DONE");
+	if (ret < 0)
+		return ret;
+
+	gpio_direction_input(gpio_done);
+
+	return 0;
+}
+
+static int fpga_config_fn(int assert, int flush, int cookie)
+{
+	int gpio_config = COOKIE2CONFIG(cookie);
+
+	debug("%s (%d): cookie=%08x gpio_config=%d\n",
+	      __func__, __LINE__, cookie, gpio_config);
+
+	if (assert)
+		gpio_set_value(gpio_config, 1);
+	else
+		gpio_set_value(gpio_config, 0);
+
+	return 0;
+}
+
+static int fpga_write_fn(const void *buf, size_t len, int flush, int cookie)
+{
+	int spi_bus = COOKIE2SPI_BUS(cookie);
+	int spi_dev = COOKIE2SPI_DEV(cookie);
+	struct kwspi_registers *reg;
+	u32 control_reg;
+	u32 config_reg;
+	void *dst;
+
+	/*
+	 * Write data to FPGA attached to SPI bus via SPI direct write.
+	 * This results in the fastest and easiest way to program the
+	 * bitstream into the FPGA.
+	 */
+	debug("%s (%d): cookie=%08x spi_bus=%d spi_dev=%d\n",
+	      __func__, __LINE__, cookie, spi_bus, spi_dev);
+
+	if (spi_bus == 0) {
+		reg = (struct kwspi_registers *)MVEBU_REGISTER(0x10600);
+		dst = (void *)SPI_BUS0_DEV1_BASE;
+	} else {
+		reg = (struct kwspi_registers *)MVEBU_REGISTER(0x10680);
+		dst = (void *)SPI_BUS1_DEV2_BASE;
+	}
+
+	/* Configure SPI controller for direct access mode */
+	control_reg = readl(&reg->ctrl);
+	config_reg = readl(&reg->cfg);
+	writel(0x00000214, &reg->cfg);		/* 27MHz clock */
+	writel(0x00000000, &reg->dw_cfg);	/* don't de-asset CS */
+	writel(KWSPI_CSN_ACT, &reg->ctrl);	/* activate CS */
+
+	/* Copy data to the SPI direct mapped window */
+	memcpy(dst, buf, len);
+
+	/* Restore original register values */
+	writel(control_reg, &reg->ctrl);
+	writel(config_reg, &reg->cfg);
+
+	return 0;
+}
+
+/* Returns the state of CONF_DONE Pin */
+static int fpga_done_fn(int cookie)
+{
+	int gpio_done = COOKIE2DONE(cookie);
+	unsigned long ts;
+
+	debug("%s (%d): cookie=%08x gpio_done=%d\n",
+	      __func__, __LINE__, cookie, gpio_done);
+
+	ts = get_timer(0);
+	do {
+		if (gpio_get_value(gpio_done))
+			return 0;
+	} while (get_timer(ts) < 1000);
+
+	/* timeout so return error */
+	return -ENODEV;
+}
+
+static altera_board_specific_func stratixv_fns = {
+	.pre = fpga_pre_fn,
+	.config = fpga_config_fn,
+	.write = fpga_write_fn,
+	.done = fpga_done_fn,
+};
+
+static Altera_desc altera_fpga[] = {
+	{
+		/* Family */
+		Altera_StratixV,
+		/* Interface type */
+		passive_serial,
+		/* No limitation as additional data will be ignored */
+		-1,
+		/* Device function table */
+		(void *)&stratixv_fns,
+		/* Base interface address specified in driver */
+		NULL,
+		/* Cookie implementation */
+		/*
+		 * In this 32bit word the following information is coded:
+		 * Bit 31 ... Bit 0
+		 * SPI-Bus | SPI-Dev | Config-Pin | Done-Pin
+		 */
+		FPGA_COOKIE(0, 1, 26, 7)
+	},
+	{
+		/* Family */
+		Altera_StratixV,
+		/* Interface type */
+		passive_serial,
+		/* No limitation as additional data will be ignored */
+		-1,
+		/* Device function table */
+		(void *)&stratixv_fns,
+		/* Base interface address specified in driver */
+		NULL,
+		/* Cookie implementation */
+		/*
+		 * In this 32bit word the following information is coded:
+		 * Bit 31 ... Bit 0
+		 * SPI-Bus | SPI-Dev | Config-Pin | Done-Pin
+		 */
+		FPGA_COOKIE(1, 2, 29, 9)
+	},
+};
+
+/* Add device descriptor to FPGA device table */
+void board_fpga_add(void)
+{
+	int i;
+
+	fpga_init();
+	for (i = 0; i < ARRAY_SIZE(altera_fpga); i++)
+		fpga_add(fpga_altera, &altera_fpga[i]);
+}
diff --git a/board/theadorable/theadorable.c b/board/theadorable/theadorable.c
index 0e232656fc..ee88a98a24 100644
--- a/board/theadorable/theadorable.c
+++ b/board/theadorable/theadorable.c
@@ -8,9 +8,11 @@
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/soc.h>
+#include <linux/mbus.h>
 #ifdef CONFIG_NET
 #include <netdev.h>
 #endif
+#include "theadorable.h"
 
 #include "../drivers/ddr/marvell/axp/ddr3_hw_training.h"
 #include "../arch/arm/mach-mvebu/serdes/axp/high_speed_env_spec.h"
@@ -136,6 +138,15 @@ int board_init(void)
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
 
+	/*
+	 * Map SPI devices via MBUS so that they can be accessed via
+	 * the SPI direct access mode
+	 */
+	mbus_dt_setup_win(&mbus_state, SPI_BUS0_DEV1_BASE, SPI_BUS0_DEV1_SIZE,
+			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_SPI0_CS1);
+	mbus_dt_setup_win(&mbus_state, SPI_BUS1_DEV2_BASE, SPI_BUS0_DEV1_SIZE,
+			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_SPI1_CS2);
+
 	return 0;
 }
 
@@ -143,6 +154,8 @@ int checkboard(void)
 {
 	puts("Board: theadorable\n");
 
+	board_fpga_add();
+
 	return 0;
 }
 
diff --git a/board/theadorable/theadorable.h b/board/theadorable/theadorable.h
new file mode 100644
index 0000000000..89fe1179a4
--- /dev/null
+++ b/board/theadorable/theadorable.h
@@ -0,0 +1,12 @@
+/*
+ * Copyright (C) 2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/* Base addresses for the SPI direct access mode */
+#define SPI_BUS0_DEV1_BASE	0xe0000000
+#define SPI_BUS0_DEV1_SIZE	(1 << 20)
+#define SPI_BUS1_DEV2_BASE	(SPI_BUS0_DEV1_BASE + SPI_BUS0_DEV1_SIZE)
+
+void board_fpga_add(void);
diff --git a/configs/theadorable_debug_defconfig b/configs/theadorable_debug_defconfig
index 62a6ee6663..054038a03b 100644
--- a/configs/theadorable_debug_defconfig
+++ b/configs/theadorable_debug_defconfig
@@ -2,6 +2,7 @@ CONFIG_ARM=y
 CONFIG_ARCH_MVEBU=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_THEADORABLE=y
+CONFIG_DM_GPIO=y
 CONFIG_DEFAULT_DEVICE_TREE="armada-xp-theadorable"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_SPL=y
@@ -10,7 +11,7 @@ CONFIG_FIT=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
-# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_SPL_OF_TRANSLATE=y
diff --git a/configs/theadorable_defconfig b/configs/theadorable_defconfig
index 4d5f3b0a0a..9a6abf2f7e 100644
--- a/configs/theadorable_defconfig
+++ b/configs/theadorable_defconfig
@@ -2,6 +2,7 @@ CONFIG_ARM=y
 CONFIG_ARCH_MVEBU=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_THEADORABLE=y
+CONFIG_DM_GPIO=y
 CONFIG_DEFAULT_DEVICE_TREE="armada-xp-theadorable"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_SPL=y
@@ -9,7 +10,6 @@ CONFIG_FIT=y
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_SF=y
-# CONFIG_CMD_FPGA is not set
 # CONFIG_CMD_SETEXPR is not set
 # CONFIG_CMD_NET is not set
 # CONFIG_CMD_NFS is not set
diff --git a/include/configs/theadorable.h b/include/configs/theadorable.h
index 9f186add71..a4bcf21210 100644
--- a/include/configs/theadorable.h
+++ b/include/configs/theadorable.h
@@ -114,6 +114,11 @@
 #define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_CMD_BMP
 
+/* FPGA programming support */
+#define CONFIG_FPGA
+#define CONFIG_FPGA_ALTERA
+#define CONFIG_FPGA_STRATIX_V
+
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros