1 files changed, 0 insertions, 126 deletions
diff --git a/binutils-2.24/gas/doc/c-rl78.texi b/binutils-2.24/gas/doc/c-rl78.texi
deleted file mode 100644
index 0964ac45..00000000
--- a/binutils-2.24/gas/doc/c-rl78.texi
+++ /dev/null
@@ -1,126 +0,0 @@
-@c Copyright 2011-2013 Free Software Foundation, Inc.
-@c This is part of the GAS manual.
-@c For copying conditions, see the file as.texinfo.
-@ifset GENERIC
-@page
-@node RL78-Dependent
-@chapter RL78 Dependent Features
-@end ifset
-@ifclear GENERIC
-@node Machine Dependencies
-@chapter RL78 Dependent Features
-@end ifclear
-
-@cindex RL78 support
-@menu
-* RL78-Opts::                   RL78 Assembler Command Line Options
-* RL78-Modifiers::              Symbolic Operand Modifiers
-* RL78-Directives::             Assembler Directives
-* RL78-Syntax::                 Syntax
-@end menu
-
-@node RL78-Opts
-@section RL78 Options
-@cindex options, RL78
-@cindex RL78 options
-
-@table @code
-@item relax
-Enable support for link-time relaxation.
-
-@item mg10
-Mark the generated binary as targeting the G10 variant of the RL78
-architecture.
-
-@end table
-
-@node RL78-Modifiers
-@section Symbolic Operand Modifiers
-
-@cindex RL78 modifiers
-@cindex syntax, RL78
-
-The RL78 has three modifiers that adjust the relocations used by the
-linker:
-
-@table @code
-
-@item %lo16()
-
-When loading a 20-bit (or wider) address into registers, this modifier
-selects the 16 least significant bits.
-
-@smallexample
-  movw ax,#%lo16(_sym)
-@end smallexample
-
-@item %hi16()
-
-When loading a 20-bit (or wider) address into registers, this modifier
-selects the 16 most significant bits.
-
-@smallexample
-  movw ax,#%hi16(_sym)
-@end smallexample
-
-@item %hi8()
-
-When loading a 20-bit (or wider) address into registers, this modifier
-selects the 8 bits that would go into CS or ES (i.e. bits 23..16).
-
-@smallexample
-  mov es, #%hi8(_sym)
-@end smallexample
-
-@end table
-
-@node RL78-Directives
-@section Assembler Directives
-
-@cindex assembler directives, RL78
-@cindex RL78 assembler directives
-
-In addition to the common directives, the RL78 adds these:
-
-@table @code
-
-@item .double
-Output a constant in ``double'' format, which is a 32-bit floating
-point value on RL78.
-
-@item .bss
-Select the BSS section.
-
-@item .3byte
-Output a constant value in a three byte format.
-
-@item .int
-@itemx .word
-Output a constant value in a four byte format.
-
-@end table
-
-@node RL78-Syntax
-@section Syntax for the RL78
-@menu
-* RL78-Chars::                Special Characters
-@end menu
-
-@node RL78-Chars
-@subsection Special Characters
-
-@cindex line comment character, RL78
-@cindex RL78 line comment character
-The presence of a @samp{;} appearing anywhere on a line indicates the
-start of a comment that extends to the end of that line.
-
-If a @samp{#} appears as the first character of a line then the whole
-line is treated as a comment, but in this case the line can also be a
-logical line number directive (@pxref{Comments}) or a preprocessor
-control command (@pxref{Preprocessing}).
-
-@cindex line separator, RL78
-@cindex statement separator, RL78
-@cindex RL78 line separator
-The @samp{|} character can be used to separate statements on the same
-line.