1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
|
config SECURITY_SELINUX
bool "NSA SELinux Support"
depends on SECURITY_NETWORK && AUDIT && NET && INET
select NETWORK_SECMARK
default n
help
This selects NSA Security-Enhanced Linux (SELinux).
You will also need a policy configuration and a labeled filesystem.
If you are unsure how to answer this question, answer N.
config SECURITY_SELINUX_BOOTPARAM
bool "NSA SELinux boot parameter"
depends on SECURITY_SELINUX
default n
help
This option adds a kernel parameter 'selinux', which allows SELinux
to be disabled at boot. If this option is selected, SELinux
functionality can be disabled with selinux=0 on the kernel
command line. The purpose of this option is to allow a single
kernel image to be distributed with SELinux built in, but not
necessarily enabled.
If you are unsure how to answer this question, answer N.
config SECURITY_SELINUX_BOOTPARAM_VALUE
int "NSA SELinux boot parameter default value"
depends on SECURITY_SELINUX_BOOTPARAM
range 0 1
default 1
help
This option sets the default value for the kernel parameter
'selinux', which allows SELinux to be disabled at boot. If this
option is set to 0 (zero), the SELinux kernel parameter will
default to 0, disabling SELinux at bootup. If this option is
set to 1 (one), the SELinux kernel parameter will default to 1,
enabling SELinux at bootup.
If you are unsure how to answer this question, answer 1.
config SECURITY_SELINUX_DISABLE
bool "NSA SELinux runtime disable"
depends on SECURITY_SELINUX
default n
help
This option enables writing to a selinuxfs node 'disable', which
allows SELinux to be disabled at runtime prior to the policy load.
SELinux will then remain disabled until the next boot.
This option is similar to the selinux=0 boot parameter, but is to
support runtime disabling of SELinux, e.g. from /sbin/init, for
portability across platforms where boot parameters are difficult
to employ.
If you are unsure how to answer this question, answer N.
config SECURITY_SELINUX_DEVELOP
bool "NSA SELinux Development Support"
depends on SECURITY_SELINUX
default y
help
This enables the development support option of NSA SELinux,
which is useful for experimenting with SELinux and developing
policies. If unsure, say Y. With this option enabled, the
kernel will start in permissive mode (log everything, deny nothing)
unless you specify enforcing=1 on the kernel command line. You
can interactively toggle the kernel between enforcing mode and
permissive mode (if permitted by the policy) via /selinux/enforce.
config SECURITY_SELINUX_AVC_STATS
bool "NSA SELinux AVC Statistics"
depends on SECURITY_SELINUX
default y
help
This option collects access vector cache statistics to
/selinux/avc/cache_stats, which may be monitored via
tools such as avcstat.
config SECURITY_SELINUX_CHECKREQPROT_VALUE
int "NSA SELinux checkreqprot default value"
depends on SECURITY_SELINUX
range 0 1
default 1
help
This option sets the default value for the 'checkreqprot' flag
that determines whether SELinux checks the protection requested
by the application or the protection that will be applied by the
kernel (including any implied execute for read-implies-exec) for
mmap and mprotect calls. If this option is set to 0 (zero),
SELinux will default to checking the protection that will be applied
by the kernel. If this option is set to 1 (one), SELinux will
default to checking the protection requested by the application.
The checkreqprot flag may be changed from the default via the
'checkreqprot=' boot parameter. It may also be changed at runtime
via /selinux/checkreqprot if authorized by policy.
If you are unsure how to answer this question, answer 1.
config SECURITY_SELINUX_ENABLE_SECMARK_DEFAULT
bool "NSA SELinux enable new secmark network controls by default"
depends on SECURITY_SELINUX
default n
help
This option determines whether the new secmark-based network
controls will be enabled by default. If not, the old internal
per-packet controls will be enabled by default, preserving
old behavior.
If you enable the new controls, you will need updated
SELinux userspace libraries, tools and policy. Typically,
your distribution will provide these and enable the new controls
in the kernel they also distribute.
Note that this option can be overridden at boot with the
selinux_compat_net parameter, and after boot via
/selinux/compat_net. See Documentation/kernel-parameters.txt
for details on this parameter.
If you enable the new network controls, you will likely
also require the SECMARK and CONNSECMARK targets, as
well as any conntrack helpers for protocols which you
wish to control.
If you are unsure what to do here, select N.
config SECURITY_SELINUX_POLICYDB_VERSION_MAX
bool "NSA SELinux maximum supported policy format version"
depends on SECURITY_SELINUX
default n
help
This option enables the maximum policy format version supported
by SELinux to be set to a particular value. This value is reported
to userspace via /selinux/policyvers and used at policy load time.
It can be adjusted downward to support legacy userland (init) that
does not correctly handle kernels that support newer policy versions.
Examples:
For the Fedora Core 3 or 4 Linux distributions, enable this option
and set the value via the next option. For Fedora Core 5 and later,
do not enable this option.
If you are unsure how to answer this question, answer N.
config SECURITY_SELINUX_POLICYDB_VERSION_MAX_VALUE
int "NSA SELinux maximum supported policy format version value"
depends on SECURITY_SELINUX_POLICYDB_VERSION_MAX
range 15 23
default 19
help
This option sets the value for the maximum policy format version
supported by SELinux.
Examples:
For Fedora Core 3, use 18.
For Fedora Core 4, use 19.
If you are unsure how to answer this question, look for the
policy format version supported by your policy toolchain, by
running 'checkpolicy -V'. Or look at what policy you have
installed under /etc/selinux/$SELINUXTYPE/policy, where
SELINUXTYPE is defined in your /etc/selinux/config.
|
