From add7b58e7558dd2894f3c17ca8574099fcba5c15 Mon Sep 17 00:00:00 2001
From: Bjorn Helgaas <bjorn.helgaas@hp.com>
Date: Mon, 24 Oct 2005 22:11:57 +0100
Subject: [SERIAL] support the Exsys EX-4055 4S four-port card

Tested by Wolfgang Denk with this device:

    00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
        Subsystem: Exsys EX-4055 4S(16C550) RS-232
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
        Region 1: I/O ports at 7080 [size=128]
        Region 2: I/O ports at 7400 [size=32]

    00:0f.0 Class 0280: 10b5:9050 (rev 01)
        Subsystem: d84d:4055

Results with this patch:

    Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    PCI: Found IRQ 10 for device 0000:00:0f.0
    ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
    ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
    ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
    ttyS7 at I/O 0x7418 (irq = 10) is a 16550A

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 drivers/serial/8250_pci.c | 25 ++++++++++++++++++++++++-
 include/linux/pci_ids.h   |  1 +
 2 files changed, 25 insertions(+), 1 deletion(-)

diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
index 0e21f583690..5da61ebbac8 100644
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -226,8 +226,10 @@ static int __devinit pci_plx9050_init(struct pci_dev *dev)
 	}
 
 	irq_config = 0x41;
-	if (dev->vendor == PCI_VENDOR_ID_PANACOM)
+	if (dev->vendor == PCI_VENDOR_ID_PANACOM ||
+	    dev->subsystem_vendor == PCI_SUBVENDOR_ID_EXSYS) {
 		irq_config = 0x43;
+	}
 	if ((dev->vendor == PCI_VENDOR_ID_PLX) &&
 	    (dev->device == PCI_DEVICE_ID_PLX_ROMULUS)) {
 		/*
@@ -661,6 +663,15 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
 	/*
 	 * PLX
 	 */
+	{
+		.vendor		= PCI_VENDOR_ID_PLX,
+		.device		= PCI_DEVICE_ID_PLX_9050,
+		.subvendor	= PCI_SUBVENDOR_ID_EXSYS,
+		.subdevice	= PCI_SUBDEVICE_ID_EXSYS_4055,
+		.init		= pci_plx9050_init,
+		.setup		= pci_default_setup,
+		.exit		= __devexit_p(pci_plx9050_exit),
+	},
 	{
 		.vendor		= PCI_VENDOR_ID_PLX,
 		.device		= PCI_DEVICE_ID_PLX_9050,
@@ -927,6 +938,7 @@ enum pci_board_num_t {
 	pbn_panacom,
 	pbn_panacom2,
 	pbn_panacom4,
+	pbn_exsys_4055,
 	pbn_plx_romulus,
 	pbn_oxsemi,
 	pbn_intel_i960,
@@ -1292,6 +1304,13 @@ static struct pciserial_board pci_boards[] __devinitdata = {
 		.reg_shift	= 7,
 	},
 
+	[pbn_exsys_4055] = {
+		.flags		= FL_BASE2,
+		.num_ports	= 4,
+		.base_baud	= 115200,
+		.uart_offset	= 8,
+	},
+
 	/* I think this entry is broken - the first_offset looks wrong --rmk */
 	[pbn_plx_romulus] = {
 		.flags		= FL_BASE2,
@@ -1853,6 +1872,10 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_SUBVENDOR_ID_CHASE_PCIRAS,
 		PCI_SUBDEVICE_ID_CHASE_PCIRAS8, 0, 0, 
 		pbn_b2_8_460800 },
+	{	PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
+		PCI_SUBVENDOR_ID_EXSYS,
+		PCI_SUBDEVICE_ID_EXSYS_4055, 0, 0,
+		pbn_exsys_4055 },
 	/*
 	 * Megawolf Romulus PCI Serial Card, from Mike Hudson
 	 * (Exoray@isys.ca)
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index f74ed946247..ca0691c319a 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2696,6 +2696,7 @@
 
 #define PCI_SUBVENDOR_ID_EXSYS		0xd84d
 #define PCI_SUBDEVICE_ID_EXSYS_4014	0x4014
+#define PCI_SUBDEVICE_ID_EXSYS_4055	0x4055
 
 #define PCI_VENDOR_ID_TIGERJET		0xe159
 #define PCI_DEVICE_ID_TIGERJET_300	0x0001
-- 
cgit v1.2.3