diff options
Diffstat (limited to 'drivers/net/cs8900.h')
| -rw-r--r-- | drivers/net/cs8900.h | 258 |
1 files changed, 258 insertions, 0 deletions
diff --git a/drivers/net/cs8900.h b/drivers/net/cs8900.h new file mode 100644 index 000000000..f886d103c --- /dev/null +++ b/drivers/net/cs8900.h @@ -0,0 +1,258 @@ +/* + * Cirrus Logic CS8900A Ethernet + * + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger@sysgo.de> + * + * Copyright (C) 1999 Ben Williamson <benw@pobox.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is loaded into SRAM in bootstrap mode, where it waits + * for commands on UART1 to read and write memory, jump to code etc. + * A design goal for this program is to be entirely independent of the + * target board. Anything with a CL-PS7111 or EP7211 should be able to run + * this code in bootstrap mode. All the board specifics can be handled on + * the host. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <asm/types.h> +#include <config.h> + +#ifdef CONFIG_DRIVER_CS8900 + +/* although the registers are 16 bit, they are 32-bit aligned on the + EDB7111. so we have to read them as 32-bit registers and ignore the + upper 16-bits. i'm not sure if this holds for the EDB7211. */ + +#ifdef CS8900_BUS16 + /* 16 bit aligned registers, 16 bit wide */ + #define CS8900_REG u16 + #define CS8900_OFF 0x02 + #define CS8900_BUS16_0 *(volatile u8 *)(CS8900_BASE+0x00) + #define CS8900_BUS16_1 *(volatile u8 *)(CS8900_BASE+0x01) +#elif defined(CS8900_BUS32) + /* 32 bit aligned registers, 16 bit wide (we ignore upper 16 bits) */ + #define CS8900_REG u32 + #define CS8900_OFF 0x04 +#else + #error unknown bussize ... +#endif + +#define CS8900_RTDATA *(volatile CS8900_REG *)(CS8900_BASE+0x00*CS8900_OFF) +#define CS8900_TxCMD *(volatile CS8900_REG *)(CS8900_BASE+0x02*CS8900_OFF) +#define CS8900_TxLEN *(volatile CS8900_REG *)(CS8900_BASE+0x03*CS8900_OFF) +#define CS8900_ISQ *(volatile CS8900_REG *)(CS8900_BASE+0x04*CS8900_OFF) +#define CS8900_PPTR *(volatile CS8900_REG *)(CS8900_BASE+0x05*CS8900_OFF) +#define CS8900_PDATA *(volatile CS8900_REG *)(CS8900_BASE+0x06*CS8900_OFF) + + +#define ISQ_RxEvent 0x04 +#define ISQ_TxEvent 0x08 +#define ISQ_BufEvent 0x0C +#define ISQ_RxMissEvent 0x10 +#define ISQ_TxColEvent 0x12 +#define ISQ_EventMask 0x3F + +/* packet page register offsets */ + +/* bus interface registers */ +#define PP_ChipID 0x0000 /* Chip identifier - must be 0x630E */ +#define PP_ChipRev 0x0002 /* Chip revision, model codes */ + +#define PP_IntReg 0x0022 /* Interrupt configuration */ +#define PP_IntReg_IRQ0 0x0000 /* Use INTR0 pin */ +#define PP_IntReg_IRQ1 0x0001 /* Use INTR1 pin */ +#define PP_IntReg_IRQ2 0x0002 /* Use INTR2 pin */ +#define PP_IntReg_IRQ3 0x0003 /* Use INTR3 pin */ + +/* status and control registers */ + +#define PP_RxCFG 0x0102 /* Receiver configuration */ +#define PP_RxCFG_Skip1 0x0040 /* Skip (i.e. discard) current frame */ +#define PP_RxCFG_Stream 0x0080 /* Enable streaming mode */ +#define PP_RxCFG_RxOK 0x0100 /* RxOK interrupt enable */ +#define PP_RxCFG_RxDMAonly 0x0200 /* Use RxDMA for all frames */ +#define PP_RxCFG_AutoRxDMA 0x0400 /* Select RxDMA automatically */ +#define PP_RxCFG_BufferCRC 0x0800 /* Include CRC characters in frame */ +#define PP_RxCFG_CRC 0x1000 /* Enable interrupt on CRC error */ +#define PP_RxCFG_RUNT 0x2000 /* Enable interrupt on RUNT frames */ +#define PP_RxCFG_EXTRA 0x4000 /* Enable interrupt on frames with extra data */ + +#define PP_RxCTL 0x0104 /* Receiver control */ +#define PP_RxCTL_IAHash 0x0040 /* Accept frames that match hash */ +#define PP_RxCTL_Promiscuous 0x0080 /* Accept any frame */ +#define PP_RxCTL_RxOK 0x0100 /* Accept well formed frames */ +#define PP_RxCTL_Multicast 0x0200 /* Accept multicast frames */ +#define PP_RxCTL_IA 0x0400 /* Accept frame that matches IA */ +#define PP_RxCTL_Broadcast 0x0800 /* Accept broadcast frames */ +#define PP_RxCTL_CRC 0x1000 /* Accept frames with bad CRC */ +#define PP_RxCTL_RUNT 0x2000 /* Accept runt frames */ +#define PP_RxCTL_EXTRA 0x4000 /* Accept frames that are too long */ + +#define PP_TxCFG 0x0106 /* Transmit configuration */ +#define PP_TxCFG_CRS 0x0040 /* Enable interrupt on loss of carrier */ +#define PP_TxCFG_SQE 0x0080 /* Enable interrupt on Signal Quality Error */ +#define PP_TxCFG_TxOK 0x0100 /* Enable interrupt on successful xmits */ +#define PP_TxCFG_Late 0x0200 /* Enable interrupt on "out of window" */ +#define PP_TxCFG_Jabber 0x0400 /* Enable interrupt on jabber detect */ +#define PP_TxCFG_Collision 0x0800 /* Enable interrupt if collision */ +#define PP_TxCFG_16Collisions 0x8000 /* Enable interrupt if > 16 collisions */ + +#define PP_TxCmd 0x0108 /* Transmit command status */ +#define PP_TxCmd_TxStart_5 0x0000 /* Start after 5 bytes in buffer */ +#define PP_TxCmd_TxStart_381 0x0040 /* Start after 381 bytes in buffer */ +#define PP_TxCmd_TxStart_1021 0x0080 /* Start after 1021 bytes in buffer */ +#define PP_TxCmd_TxStart_Full 0x00C0 /* Start after all bytes loaded */ +#define PP_TxCmd_Force 0x0100 /* Discard any pending packets */ +#define PP_TxCmd_OneCollision 0x0200 /* Abort after a single collision */ +#define PP_TxCmd_NoCRC 0x1000 /* Do not add CRC */ +#define PP_TxCmd_NoPad 0x2000 /* Do not pad short packets */ + +#define PP_BufCFG 0x010A /* Buffer configuration */ +#define PP_BufCFG_SWI 0x0040 /* Force interrupt via software */ +#define PP_BufCFG_RxDMA 0x0080 /* Enable interrupt on Rx DMA */ +#define PP_BufCFG_TxRDY 0x0100 /* Enable interrupt when ready for Tx */ +#define PP_BufCFG_TxUE 0x0200 /* Enable interrupt in Tx underrun */ +#define PP_BufCFG_RxMiss 0x0400 /* Enable interrupt on missed Rx packets */ +#define PP_BufCFG_Rx128 0x0800 /* Enable Rx interrupt after 128 bytes */ +#define PP_BufCFG_TxCol 0x1000 /* Enable int on Tx collision ctr overflow */ +#define PP_BufCFG_Miss 0x2000 /* Enable int on Rx miss ctr overflow */ +#define PP_BufCFG_RxDest 0x8000 /* Enable int on Rx dest addr match */ + +#define PP_LineCTL 0x0112 /* Line control */ +#define PP_LineCTL_Rx 0x0040 /* Enable receiver */ +#define PP_LineCTL_Tx 0x0080 /* Enable transmitter */ +#define PP_LineCTL_AUIonly 0x0100 /* AUI interface only */ +#define PP_LineCTL_AutoAUI10BT 0x0200 /* Autodetect AUI or 10BaseT interface */ +#define PP_LineCTL_ModBackoffE 0x0800 /* Enable modified backoff algorithm */ +#define PP_LineCTL_PolarityDis 0x1000 /* Disable Rx polarity autodetect */ +#define PP_LineCTL_2partDefDis 0x2000 /* Disable two-part defferal */ +#define PP_LineCTL_LoRxSquelch 0x4000 /* Reduce receiver squelch threshold */ + +#define PP_SelfCTL 0x0114 /* Chip self control */ +#define PP_SelfCTL_Reset 0x0040 /* Self-clearing reset */ +#define PP_SelfCTL_SWSuspend 0x0100 /* Initiate suspend mode */ +#define PP_SelfCTL_HWSleepE 0x0200 /* Enable SLEEP input */ +#define PP_SelfCTL_HWStandbyE 0x0400 /* Enable standby mode */ +#define PP_SelfCTL_HC0E 0x1000 /* use HCB0 for LINK LED */ +#define PP_SelfCTL_HC1E 0x2000 /* use HCB1 for BSTATUS LED */ +#define PP_SelfCTL_HCB0 0x4000 /* control LINK LED if HC0E set */ +#define PP_SelfCTL_HCB1 0x8000 /* control BSTATUS LED if HC1E set */ + +#define PP_BusCTL 0x0116 /* Bus control */ +#define PP_BusCTL_ResetRxDMA 0x0040 /* Reset RxDMA pointer */ +#define PP_BusCTL_DMAextend 0x0100 /* Extend DMA cycle */ +#define PP_BusCTL_UseSA 0x0200 /* Assert MEMCS16 on address decode */ +#define PP_BusCTL_MemoryE 0x0400 /* Enable memory mode */ +#define PP_BusCTL_DMAburst 0x0800 /* Limit DMA access burst */ +#define PP_BusCTL_IOCHRDYE 0x1000 /* Set IOCHRDY high impedence */ +#define PP_BusCTL_RxDMAsize 0x2000 /* Set DMA buffer size 64KB */ +#define PP_BusCTL_EnableIRQ 0x8000 /* Generate interrupt on interrupt event */ + +#define PP_TestCTL 0x0118 /* Test control */ +#define PP_TestCTL_DisableLT 0x0080 /* Disable link status */ +#define PP_TestCTL_ENDECloop 0x0200 /* Internal loopback */ +#define PP_TestCTL_AUIloop 0x0400 /* AUI loopback */ +#define PP_TestCTL_DisBackoff 0x0800 /* Disable backoff algorithm */ +#define PP_TestCTL_FDX 0x4000 /* Enable full duplex mode */ + +#define PP_ISQ 0x0120 /* Interrupt Status Queue */ + +#define PP_RER 0x0124 /* Receive event */ +#define PP_RER_IAHash 0x0040 /* Frame hash match */ +#define PP_RER_Dribble 0x0080 /* Frame had 1-7 extra bits after last byte */ +#define PP_RER_RxOK 0x0100 /* Frame received with no errors */ +#define PP_RER_Hashed 0x0200 /* Frame address hashed OK */ +#define PP_RER_IA 0x0400 /* Frame address matched IA */ +#define PP_RER_Broadcast 0x0800 /* Broadcast frame */ +#define PP_RER_CRC 0x1000 /* Frame had CRC error */ +#define PP_RER_RUNT 0x2000 /* Runt frame */ +#define PP_RER_EXTRA 0x4000 /* Frame was too long */ + +#define PP_TER 0x0128 /* Transmit event */ +#define PP_TER_CRS 0x0040 /* Carrier lost */ +#define PP_TER_SQE 0x0080 /* Signal Quality Error */ +#define PP_TER_TxOK 0x0100 /* Packet sent without error */ +#define PP_TER_Late 0x0200 /* Out of window */ +#define PP_TER_Jabber 0x0400 /* Stuck transmit? */ +#define PP_TER_NumCollisions 0x7800 /* Number of collisions */ +#define PP_TER_16Collisions 0x8000 /* > 16 collisions */ + +#define PP_BER 0x012C /* Buffer event */ +#define PP_BER_SWint 0x0040 /* Software interrupt */ +#define PP_BER_RxDMAFrame 0x0080 /* Received framed DMAed */ +#define PP_BER_Rdy4Tx 0x0100 /* Ready for transmission */ +#define PP_BER_TxUnderrun 0x0200 /* Transmit underrun */ +#define PP_BER_RxMiss 0x0400 /* Received frame missed */ +#define PP_BER_Rx128 0x0800 /* 128 bytes received */ +#define PP_BER_RxDest 0x8000 /* Received framed passed address filter */ + +#define PP_RxMiss 0x0130 /* Receiver miss counter */ + +#define PP_TxCol 0x0132 /* Transmit collision counter */ + +#define PP_LineSTAT 0x0134 /* Line status */ +#define PP_LineSTAT_LinkOK 0x0080 /* Line is connected and working */ +#define PP_LineSTAT_AUI 0x0100 /* Connected via AUI */ +#define PP_LineSTAT_10BT 0x0200 /* Connected via twisted pair */ +#define PP_LineSTAT_Polarity 0x1000 /* Line polarity OK (10BT only) */ +#define PP_LineSTAT_CRS 0x4000 /* Frame being received */ + +#define PP_SelfSTAT 0x0136 /* Chip self status */ +#define PP_SelfSTAT_33VActive 0x0040 /* supply voltage is 3.3V */ +#define PP_SelfSTAT_InitD 0x0080 /* Chip initialization complete */ +#define PP_SelfSTAT_SIBSY 0x0100 /* EEPROM is busy */ +#define PP_SelfSTAT_EEPROM 0x0200 /* EEPROM present */ +#define PP_SelfSTAT_EEPROM_OK 0x0400 /* EEPROM checks out */ +#define PP_SelfSTAT_ELPresent 0x0800 /* External address latch logic available */ +#define PP_SelfSTAT_EEsize 0x1000 /* Size of EEPROM */ + +#define PP_BusSTAT 0x0138 /* Bus status */ +#define PP_BusSTAT_TxBid 0x0080 /* Tx error */ +#define PP_BusSTAT_TxRDY 0x0100 /* Ready for Tx data */ + +#define PP_TDR 0x013C /* AUI Time Domain Reflectometer */ + +/* initiate transmit registers */ + +#define PP_TxCommand 0x0144 /* Tx Command */ +#define PP_TxLength 0x0146 /* Tx Length */ + + +/* address filter registers */ + +#define PP_LAF 0x0150 /* Logical address filter (6 bytes) */ +#define PP_IA 0x0158 /* Individual address (MAC) */ + +/* EEPROM Kram */ +#define SI_BUSY 0x0100 +#define PP_SelfST 0x0136 /* Self State register */ +#define PP_EECMD 0x0040 /* NVR Interface Command register */ +#define PP_EEData 0x0042 /* NVR Interface Data Register */ +#define EEPROM_WRITE_EN 0x00F0 +#define EEPROM_WRITE_DIS 0x0000 +#define EEPROM_WRITE_CMD 0x0100 +#define EEPROM_READ_CMD 0x0200 +#define EEPROM_ERASE_CMD 0x0300 + +extern int cs8900_e2prom_read(uchar, ushort *); +extern int cs8900_e2prom_write(uchar, ushort); + +#endif /* CONFIG_DRIVER_CS8900 */ |