diff options
Diffstat (limited to 'drivers/net')
30 files changed, 523 insertions, 164 deletions
diff --git a/drivers/net/atlx/atl2.c b/drivers/net/atlx/atl2.c index e637e9f28fd4..937ef1afa5db 100644 --- a/drivers/net/atlx/atl2.c +++ b/drivers/net/atlx/atl2.c @@ -1996,13 +1996,15 @@ static int atl2_set_eeprom(struct net_device *netdev, if (!eeprom_buff) return -ENOMEM; - ptr = (u32 *)eeprom_buff; + ptr = eeprom_buff; if (eeprom->offset & 3) { /* need read/modify/write of first changed EEPROM word */ /* only the second byte of the word is being modified */ - if (!atl2_read_eeprom(hw, first_dword*4, &(eeprom_buff[0]))) - return -EIO; + if (!atl2_read_eeprom(hw, first_dword*4, &(eeprom_buff[0]))) { + ret_val = -EIO; + goto out; + } ptr++; } if (((eeprom->offset + eeprom->len) & 3)) { @@ -2011,18 +2013,22 @@ static int atl2_set_eeprom(struct net_device *netdev, * only the first byte of the word is being modified */ if (!atl2_read_eeprom(hw, last_dword * 4, - &(eeprom_buff[last_dword - first_dword]))) - return -EIO; + &(eeprom_buff[last_dword - first_dword]))) { + ret_val = -EIO; + goto out; + } } /* Device's eeprom is always little-endian, word addressable */ memcpy(ptr, bytes, eeprom->len); for (i = 0; i < last_dword - first_dword + 1; i++) { - if (!atl2_write_eeprom(hw, ((first_dword+i)*4), eeprom_buff[i])) - return -EIO; + if (!atl2_write_eeprom(hw, ((first_dword+i)*4), eeprom_buff[i])) { + ret_val = -EIO; + goto out; + } } - + out: kfree(eeprom_buff); return ret_val; } diff --git a/drivers/net/bfin_mac.c b/drivers/net/bfin_mac.c index 22abfb39d813..68d45ba2d9b9 100644 --- a/drivers/net/bfin_mac.c +++ b/drivers/net/bfin_mac.c @@ -1237,8 +1237,17 @@ static int bfin_mac_enable(struct phy_device *phydev) if (phydev->interface == PHY_INTERFACE_MODE_RMII) { opmode |= RMII; /* For Now only 100MBit are supported */ -#if (defined(CONFIG_BF537) || defined(CONFIG_BF536)) && CONFIG_BF_REV_0_2 - opmode |= TE; +#if defined(CONFIG_BF537) || defined(CONFIG_BF536) + if (__SILICON_REVISION__ < 3) { + /* + * This isn't publicly documented (fun times!), but in + * silicon <=0.2, the RX and TX pins are clocked together. + * So in order to recv, we must enable the transmit side + * as well. This will cause a spurious TX interrupt too, + * but we can easily consume that. + */ + opmode |= TE; + } #endif } diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index d1865cc97313..8e6d618b5305 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -8317,7 +8317,7 @@ static const struct net_device_ops bnx2_netdev_ops = { #endif }; -static void inline vlan_features_add(struct net_device *dev, u32 flags) +static inline void vlan_features_add(struct net_device *dev, u32 flags) { dev->vlan_features |= flags; } diff --git a/drivers/net/bonding/bond_alb.h b/drivers/net/bonding/bond_alb.h index 118c28aa471e..4b3e35878406 100644 --- a/drivers/net/bonding/bond_alb.h +++ b/drivers/net/bonding/bond_alb.h @@ -74,7 +74,7 @@ struct tlb_client_info { * packets to a Client that the Hash function * gave this entry index. */ - u32 tx_bytes; /* Each Client acumulates the BytesTx that + u32 tx_bytes; /* Each Client accumulates the BytesTx that * were tranmitted to it, and after each * CallBack the LoadHistory is devided * by the balance interval diff --git a/drivers/net/can/c_can/c_can.c b/drivers/net/can/c_can/c_can.c index 110eda01843c..31552959aed7 100644 --- a/drivers/net/can/c_can/c_can.c +++ b/drivers/net/can/c_can/c_can.c @@ -588,14 +588,9 @@ static void c_can_chip_config(struct net_device *dev) { struct c_can_priv *priv = netdev_priv(dev); - if (priv->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT) - /* disable automatic retransmission */ - priv->write_reg(priv, &priv->regs->control, - CONTROL_DISABLE_AR); - else - /* enable automatic retransmission */ - priv->write_reg(priv, &priv->regs->control, - CONTROL_ENABLE_AR); + /* enable automatic retransmission */ + priv->write_reg(priv, &priv->regs->control, + CONTROL_ENABLE_AR); if (priv->can.ctrlmode & (CAN_CTRLMODE_LISTENONLY & CAN_CTRLMODE_LOOPBACK)) { @@ -704,7 +699,6 @@ static void c_can_do_tx(struct net_device *dev) for (/* nix */; (priv->tx_next - priv->tx_echo) > 0; priv->tx_echo++) { msg_obj_no = get_tx_echo_msg_obj(priv); - c_can_inval_msg_object(dev, 0, msg_obj_no); val = c_can_read_reg32(priv, &priv->regs->txrqst1); if (!(val & (1 << msg_obj_no))) { can_get_echo_skb(dev, @@ -713,6 +707,7 @@ static void c_can_do_tx(struct net_device *dev) &priv->regs->ifregs[0].msg_cntrl) & IF_MCONT_DLC_MASK; stats->tx_packets++; + c_can_inval_msg_object(dev, 0, msg_obj_no); } } @@ -1112,8 +1107,7 @@ struct net_device *alloc_c_can_dev(void) priv->can.bittiming_const = &c_can_bittiming_const; priv->can.do_set_mode = c_can_set_mode; priv->can.do_get_berr_counter = c_can_get_berr_counter; - priv->can.ctrlmode_supported = CAN_CTRLMODE_ONE_SHOT | - CAN_CTRLMODE_LOOPBACK | + priv->can.ctrlmode_supported = CAN_CTRLMODE_LOOPBACK | CAN_CTRLMODE_LISTENONLY | CAN_CTRLMODE_BERR_REPORTING; diff --git a/drivers/net/can/c_can/c_can_platform.c b/drivers/net/can/c_can/c_can_platform.c index e629b961ae2d..cc90824f2c9c 100644 --- a/drivers/net/can/c_can/c_can_platform.c +++ b/drivers/net/can/c_can/c_can_platform.c @@ -73,7 +73,8 @@ static int __devinit c_can_plat_probe(struct platform_device *pdev) void __iomem *addr; struct net_device *dev; struct c_can_priv *priv; - struct resource *mem, *irq; + struct resource *mem; + int irq; #ifdef CONFIG_HAVE_CLK struct clk *clk; @@ -88,8 +89,8 @@ static int __devinit c_can_plat_probe(struct platform_device *pdev) /* get the platform data */ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); - irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); - if (!mem || (irq <= 0)) { + irq = platform_get_irq(pdev, 0); + if (!mem || irq <= 0) { ret = -ENODEV; goto exit_free_clk; } @@ -117,7 +118,7 @@ static int __devinit c_can_plat_probe(struct platform_device *pdev) priv = netdev_priv(dev); - dev->irq = irq->start; + dev->irq = irq; priv->regs = addr; #ifdef CONFIG_HAVE_CLK priv->can.clock.freq = clk_get_rate(clk); diff --git a/drivers/net/cxgb3/cxgb3_main.c b/drivers/net/cxgb3/cxgb3_main.c index 4d538a4e9d55..910893143295 100644 --- a/drivers/net/cxgb3/cxgb3_main.c +++ b/drivers/net/cxgb3/cxgb3_main.c @@ -1983,14 +1983,20 @@ static int set_coalesce(struct net_device *dev, struct ethtool_coalesce *c) { struct port_info *pi = netdev_priv(dev); struct adapter *adapter = pi->adapter; - struct qset_params *qsp = &adapter->params.sge.qset[0]; - struct sge_qset *qs = &adapter->sge.qs[0]; + struct qset_params *qsp; + struct sge_qset *qs; + int i; if (c->rx_coalesce_usecs * 10 > M_NEWTIMER) return -EINVAL; - qsp->coalesce_usecs = c->rx_coalesce_usecs; - t3_update_qset_coalesce(qs, qsp); + for (i = 0; i < pi->nqsets; i++) { + qsp = &adapter->params.sge.qset[i]; + qs = &adapter->sge.qs[i]; + qsp->coalesce_usecs = c->rx_coalesce_usecs; + t3_update_qset_coalesce(qs, qsp); + } + return 0; } diff --git a/drivers/net/dm9000.c b/drivers/net/dm9000.c index 317708113601..b7af5bab9937 100644 --- a/drivers/net/dm9000.c +++ b/drivers/net/dm9000.c @@ -621,9 +621,9 @@ static int dm9000_set_wol(struct net_device *dev, struct ethtool_wolinfo *w) /* change in wol state, update IRQ state */ if (!dm->wake_state) - set_irq_wake(dm->irq_wake, 1); + irq_set_irq_wake(dm->irq_wake, 1); else if (dm->wake_state & !opts) - set_irq_wake(dm->irq_wake, 0); + irq_set_irq_wake(dm->irq_wake, 0); } dm->wake_state = opts; @@ -1424,13 +1424,13 @@ dm9000_probe(struct platform_device *pdev) } else { /* test to see if irq is really wakeup capable */ - ret = set_irq_wake(db->irq_wake, 1); + ret = irq_set_irq_wake(db->irq_wake, 1); if (ret) { dev_err(db->dev, "irq %d cannot set wakeup (%d)\n", db->irq_wake, ret); ret = 0; } else { - set_irq_wake(db->irq_wake, 0); + irq_set_irq_wake(db->irq_wake, 0); db->wake_supported = 1; } } diff --git a/drivers/net/irda/via-ircc.c b/drivers/net/irda/via-ircc.c index 67c0ad42d818..186cd28a61cc 100644 --- a/drivers/net/irda/via-ircc.c +++ b/drivers/net/irda/via-ircc.c @@ -75,15 +75,9 @@ static int dongle_id = 0; /* default: probe */ /* We can't guess the type of connected dongle, user *must* supply it. */ module_param(dongle_id, int, 0); -/* FIXME : we should not need this, because instances should be automatically - * managed by the PCI layer. Especially that we seem to only be using the - * first entry. Jean II */ -/* Max 4 instances for now */ -static struct via_ircc_cb *dev_self[] = { NULL, NULL, NULL, NULL }; - /* Some prototypes */ -static int via_ircc_open(int i, chipio_t * info, unsigned int id); -static int via_ircc_close(struct via_ircc_cb *self); +static int via_ircc_open(struct pci_dev *pdev, chipio_t * info, + unsigned int id); static int via_ircc_dma_receive(struct via_ircc_cb *self); static int via_ircc_dma_receive_complete(struct via_ircc_cb *self, int iobase); @@ -215,7 +209,7 @@ static int __devinit via_init_one (struct pci_dev *pcidev, const struct pci_devi pci_write_config_byte(pcidev,0x42,(bTmp | 0xf0)); pci_write_config_byte(pcidev,0x5a,0xc0); WriteLPCReg(0x28, 0x70 ); - if (via_ircc_open(0, &info,0x3076) == 0) + if (via_ircc_open(pcidev, &info, 0x3076) == 0) rc=0; } else rc = -ENODEV; //IR not turn on @@ -254,7 +248,7 @@ static int __devinit via_init_one (struct pci_dev *pcidev, const struct pci_devi info.irq=FirIRQ; info.dma=FirDRQ1; info.dma2=FirDRQ0; - if (via_ircc_open(0, &info,0x3096) == 0) + if (via_ircc_open(pcidev, &info, 0x3096) == 0) rc=0; } else rc = -ENODEV; //IR not turn on !!!!! @@ -264,48 +258,10 @@ static int __devinit via_init_one (struct pci_dev *pcidev, const struct pci_devi return rc; } -/* - * Function via_ircc_clean () - * - * Close all configured chips - * - */ -static void via_ircc_clean(void) -{ - int i; - - IRDA_DEBUG(3, "%s()\n", __func__); - - for (i=0; i < ARRAY_SIZE(dev_self); i++) { - if (dev_self[i]) - via_ircc_close(dev_self[i]); - } -} - -static void __devexit via_remove_one (struct pci_dev *pdev) -{ - IRDA_DEBUG(3, "%s()\n", __func__); - - /* FIXME : This is ugly. We should use pci_get_drvdata(pdev); - * to get our driver instance and call directly via_ircc_close(). - * See vlsi_ir for details... - * Jean II */ - via_ircc_clean(); - - /* FIXME : This should be in via_ircc_close(), because here we may - * theoritically disable still configured devices :-( - Jean II */ - pci_disable_device(pdev); -} - static void __exit via_ircc_cleanup(void) { IRDA_DEBUG(3, "%s()\n", __func__); - /* FIXME : This should be redundant, as pci_unregister_driver() - * should call via_remove_one() on each device. - * Jean II */ - via_ircc_clean(); - /* Cleanup all instances of the driver */ pci_unregister_driver (&via_driver); } @@ -324,12 +280,13 @@ static const struct net_device_ops via_ircc_fir_ops = { }; /* - * Function via_ircc_open (iobase, irq) + * Function via_ircc_open(pdev, iobase, irq) * * Open driver instance * */ -static __devinit int via_ircc_open(int i, chipio_t * info, unsigned int id) +static __devinit int via_ircc_open(struct pci_dev *pdev, chipio_t * info, + unsigned int id) { struct net_device *dev; struct via_ircc_cb *self; @@ -337,9 +294,6 @@ static __devinit int via_ircc_open(int i, chipio_t * info, unsigned int id) IRDA_DEBUG(3, "%s()\n", __func__); - if (i >= ARRAY_SIZE(dev_self)) - return -ENOMEM; - /* Allocate new instance of the driver */ dev = alloc_irdadev(sizeof(struct via_ircc_cb)); if (dev == NULL) @@ -349,13 +303,8 @@ static __devinit int via_ircc_open(int i, chipio_t * info, unsigned int id) self->netdev = dev; spin_lock_init(&self->lock); - /* FIXME : We should store our driver instance in the PCI layer, - * using pci_set_drvdata(), not in this array. - * See vlsi_ir for details... - Jean II */ - /* FIXME : 'i' is always 0 (see via_init_one()) :-( - Jean II */ - /* Need to store self somewhere */ - dev_self[i] = self; - self->index = i; + pci_set_drvdata(pdev, self); + /* Initialize Resource */ self->io.cfg_base = info->cfg_base; self->io.fir_base = info->fir_base; @@ -414,7 +363,7 @@ static __devinit int via_ircc_open(int i, chipio_t * info, unsigned int id) /* Allocate memory if needed */ self->rx_buff.head = - dma_alloc_coherent(NULL, self->rx_buff.truesize, + dma_alloc_coherent(&pdev->dev, self->rx_buff.truesize, &self->rx_buff_dma, GFP_KERNEL); if (self->rx_buff.head == NULL) { err = -ENOMEM; @@ -423,7 +372,7 @@ static __devinit int via_ircc_open(int i, chipio_t * info, unsigned int id) memset(self->rx_buff.head, 0, self->rx_buff.truesize); self->tx_buff.head = - dma_alloc_coherent(NULL, self->tx_buff.truesize, + dma_alloc_coherent(&pdev->dev, self->tx_buff.truesize, &self->tx_buff_dma, GFP_KERNEL); if (self->tx_buff.head == NULL) { err = -ENOMEM; @@ -455,33 +404,32 @@ static __devinit int via_ircc_open(int i, chipio_t * info, unsigned int id) via_hw_init(self); return 0; err_out4: - dma_free_coherent(NULL, self->tx_buff.truesize, + dma_free_coherent(&pdev->dev, self->tx_buff.truesize, self->tx_buff.head, self->tx_buff_dma); err_out3: - dma_free_coherent(NULL, self->rx_buff.truesize, + dma_free_coherent(&pdev->dev, self->rx_buff.truesize, self->rx_buff.head, self->rx_buff_dma); err_out2: release_region(self->io.fir_base, self->io.fir_ext); err_out1: + pci_set_drvdata(pdev, NULL); free_netdev(dev); - dev_self[i] = NULL; return err; } /* - * Function via_ircc_close (self) + * Function via_remove_one(pdev) * * Close driver instance * */ -static int via_ircc_close(struct via_ircc_cb *self) +static void __devexit via_remove_one(struct pci_dev *pdev) { + struct via_ircc_cb *self = pci_get_drvdata(pdev); int iobase; IRDA_DEBUG(3, "%s()\n", __func__); - IRDA_ASSERT(self != NULL, return -1;); - iobase = self->io.fir_base; ResetChip(iobase, 5); //hardware reset. @@ -493,16 +441,16 @@ static int via_ircc_close(struct via_ircc_cb *self) __func__, self->io.fir_base); release_region(self->io.fir_base, self->io.fir_ext); if (self->tx_buff.head) - dma_free_coherent(NULL, self->tx_buff.truesize, + dma_free_coherent(&pdev->dev, self->tx_buff.truesize, self->tx_buff.head, self->tx_buff_dma); if (self->rx_buff.head) - dma_free_coherent(NULL, self->rx_buff.truesize, + dma_free_coherent(&pdev->dev, self->rx_buff.truesize, self->rx_buff.head, self->rx_buff_dma); - dev_self[self->index] = NULL; + pci_set_drvdata(pdev, NULL); free_netdev(self->netdev); - return 0; + pci_disable_device(pdev); } /* diff --git a/drivers/net/jme.c b/drivers/net/jme.c index f690474f4409..994c80939c7a 100644 --- a/drivers/net/jme.c +++ b/drivers/net/jme.c @@ -273,7 +273,7 @@ jme_clear_pm(struct jme_adapter *jme) { jwrite32(jme, JME_PMCS, 0xFFFF0000 | jme->reg_pmcs); pci_set_power_state(jme->pdev, PCI_D0); - pci_enable_wake(jme->pdev, PCI_D0, false); + device_set_wakeup_enable(&jme->pdev->dev, false); } static int @@ -2538,6 +2538,8 @@ jme_set_wol(struct net_device *netdev, jwrite32(jme, JME_PMCS, jme->reg_pmcs); + device_set_wakeup_enable(&jme->pdev->dev, jme->reg_pmcs); + return 0; } @@ -3172,9 +3174,9 @@ jme_shutdown(struct pci_dev *pdev) } #ifdef CONFIG_PM -static int -jme_suspend(struct pci_dev *pdev, pm_message_t state) +static int jme_suspend(struct device *dev) { + struct pci_dev *pdev = to_pci_dev(dev); struct net_device *netdev = pci_get_drvdata(pdev); struct jme_adapter *jme = netdev_priv(netdev); @@ -3206,22 +3208,18 @@ jme_suspend(struct pci_dev *pdev, pm_message_t state) tasklet_hi_enable(&jme->rxclean_task); tasklet_hi_enable(&jme->rxempty_task); - pci_save_state(pdev); jme_powersave_phy(jme); - pci_enable_wake(jme->pdev, PCI_D3hot, true); - pci_set_power_state(pdev, PCI_D3hot); return 0; } -static int -jme_resume(struct pci_dev *pdev) +static int jme_resume(struct device *dev) { + struct pci_dev *pdev = to_pci_dev(dev); struct net_device *netdev = pci_get_drvdata(pdev); struct jme_adapter *jme = netdev_priv(netdev); - jme_clear_pm(jme); - pci_restore_state(pdev); + jwrite32(jme, JME_PMCS, 0xFFFF0000 | jme->reg_pmcs); jme_phy_on(jme); if (test_bit(JME_FLAG_SSET, &jme->flags)) @@ -3238,6 +3236,13 @@ jme_resume(struct pci_dev *pdev) return 0; } + +static SIMPLE_DEV_PM_OPS(jme_pm_ops, jme_suspend, jme_resume); +#define JME_PM_OPS (&jme_pm_ops) + +#else + +#define JME_PM_OPS NULL #endif static DEFINE_PCI_DEVICE_TABLE(jme_pci_tbl) = { @@ -3251,11 +3256,8 @@ static struct pci_driver jme_driver = { .id_table = jme_pci_tbl, .probe = jme_init_one, .remove = __devexit_p(jme_remove_one), -#ifdef CONFIG_PM - .suspend = jme_suspend, - .resume = jme_resume, -#endif /* CONFIG_PM */ .shutdown = jme_shutdown, + .driver.pm = JME_PM_OPS, }; static int __init diff --git a/drivers/net/ksz884x.c b/drivers/net/ksz884x.c index 540a8dcbcc46..7f7d5708a658 100644 --- a/drivers/net/ksz884x.c +++ b/drivers/net/ksz884x.c @@ -4898,7 +4898,7 @@ static netdev_tx_t netdev_tx(struct sk_buff *skb, struct net_device *dev) goto unlock; } skb_copy_and_csum_dev(org_skb, skb->data); - org_skb->ip_summed = 0; + org_skb->ip_summed = CHECKSUM_NONE; skb->len = org_skb->len; copy_old_skb(org_skb, skb); } diff --git a/drivers/net/mlx4/en_netdev.c b/drivers/net/mlx4/en_netdev.c index 5762ebde4455..4f158baa0246 100644 --- a/drivers/net/mlx4/en_netdev.c +++ b/drivers/net/mlx4/en_netdev.c @@ -742,6 +742,9 @@ int mlx4_en_start_port(struct net_device *dev) 0, MLX4_PROT_ETH)) mlx4_warn(mdev, "Failed Attaching Broadcast\n"); + /* Must redo promiscuous mode setup. */ + priv->flags &= ~(MLX4_EN_FLAG_PROMISC | MLX4_EN_FLAG_MC_PROMISC); + /* Schedule multicast task to populate multicast list */ queue_work(mdev->workqueue, &priv->mcast_task); diff --git a/drivers/net/mlx4/eq.c b/drivers/net/mlx4/eq.c index 506cfd0372ec..1ad1f6029af8 100644 --- a/drivers/net/mlx4/eq.c +++ b/drivers/net/mlx4/eq.c @@ -603,7 +603,9 @@ int mlx4_init_eq_table(struct mlx4_dev *dev) } for (i = 0; i < dev->caps.num_comp_vectors; ++i) { - err = mlx4_create_eq(dev, dev->caps.num_cqs + MLX4_NUM_SPARE_EQE, + err = mlx4_create_eq(dev, dev->caps.num_cqs - + dev->caps.reserved_cqs + + MLX4_NUM_SPARE_EQE, (dev->flags & MLX4_FLAG_MSI_X) ? i : 0, &priv->eq_table.eq[i]); if (err) { diff --git a/drivers/net/mlx4/mcg.c b/drivers/net/mlx4/mcg.c index e71372aa9cc4..37150b2f6425 100644 --- a/drivers/net/mlx4/mcg.c +++ b/drivers/net/mlx4/mcg.c @@ -469,7 +469,6 @@ static int remove_promisc_qp(struct mlx4_dev *dev, u8 vep_num, u8 port, /*remove from list of promisc qps */ list_del(&pqp->list); - kfree(pqp); /* set the default entry not to include the removed one */ mailbox = mlx4_alloc_cmd_mailbox(dev); @@ -528,6 +527,8 @@ out_mailbox: out_list: if (back_to_list) list_add_tail(&pqp->list, &s_steer->promisc_qps[steer]); + else + kfree(pqp); out_mutex: mutex_unlock(&priv->mcg_table.mutex); return err; diff --git a/drivers/net/myri10ge/myri10ge.c b/drivers/net/myri10ge/myri10ge.c index 1f4e8680a96a..673dc600c891 100644 --- a/drivers/net/myri10ge/myri10ge.c +++ b/drivers/net/myri10ge/myri10ge.c @@ -1312,17 +1312,26 @@ myri10ge_unmap_rx_page(struct pci_dev *pdev, * page into an skb */ static inline int -myri10ge_rx_done(struct myri10ge_slice_state *ss, struct myri10ge_rx_buf *rx, - int bytes, int len, __wsum csum) +myri10ge_rx_done(struct myri10ge_slice_state *ss, int len, __wsum csum, + int lro_enabled) { struct myri10ge_priv *mgp = ss->mgp; struct sk_buff *skb; struct skb_frag_struct rx_frags[MYRI10GE_MAX_FRAGS_PER_FRAME]; - int i, idx, hlen, remainder; + struct myri10ge_rx_buf *rx; + int i, idx, hlen, remainder, bytes; struct pci_dev *pdev = mgp->pdev; struct net_device *dev = mgp->dev; u8 *va; + if (len <= mgp->small_bytes) { + rx = &ss->rx_small; + bytes = mgp->small_bytes; + } else { + rx = &ss->rx_big; + bytes = mgp->big_bytes; + } + len += MXGEFW_PAD; idx = rx->cnt & rx->mask; va = page_address(rx->info[idx].page) + rx->info[idx].page_offset; @@ -1341,7 +1350,7 @@ myri10ge_rx_done(struct myri10ge_slice_state *ss, struct myri10ge_rx_buf *rx, remainder -= MYRI10GE_ALLOC_SIZE; } - if (dev->features & NETIF_F_LRO) { + if (lro_enabled) { rx_frags[0].page_offset += MXGEFW_PAD; rx_frags[0].size -= MXGEFW_PAD; len -= MXGEFW_PAD; @@ -1463,7 +1472,7 @@ myri10ge_clean_rx_done(struct myri10ge_slice_state *ss, int budget) { struct myri10ge_rx_done *rx_done = &ss->rx_done; struct myri10ge_priv *mgp = ss->mgp; - struct net_device *netdev = mgp->dev; + unsigned long rx_bytes = 0; unsigned long rx_packets = 0; unsigned long rx_ok; @@ -1474,18 +1483,18 @@ myri10ge_clean_rx_done(struct myri10ge_slice_state *ss, int budget) u16 length; __wsum checksum; + /* + * Prevent compiler from generating more than one ->features memory + * access to avoid theoretical race condition with functions that + * change NETIF_F_LRO flag at runtime. + */ + bool lro_enabled = ACCESS_ONCE(mgp->dev->features) & NETIF_F_LRO; + while (rx_done->entry[idx].length != 0 && work_done < budget) { length = ntohs(rx_done->entry[idx].length); rx_done->entry[idx].length = 0; checksum = csum_unfold(rx_done->entry[idx].checksum); - if (length <= mgp->small_bytes) - rx_ok = myri10ge_rx_done(ss, &ss->rx_small, - mgp->small_bytes, - length, checksum); - else - rx_ok = myri10ge_rx_done(ss, &ss->rx_big, - mgp->big_bytes, - length, checksum); + rx_ok = myri10ge_rx_done(ss, length, checksum, lro_enabled); rx_packets += rx_ok; rx_bytes += rx_ok * (unsigned long)length; cnt++; @@ -1497,7 +1506,7 @@ myri10ge_clean_rx_done(struct myri10ge_slice_state *ss, int budget) ss->stats.rx_packets += rx_packets; ss->stats.rx_bytes += rx_bytes; - if (netdev->features & NETIF_F_LRO) + if (lro_enabled) lro_flush_all(&rx_done->lro_mgr); /* restock receive rings if needed */ diff --git a/drivers/net/netxen/netxen_nic_ethtool.c b/drivers/net/netxen/netxen_nic_ethtool.c index 653d308e0f5d..3bdcc803ec68 100644 --- a/drivers/net/netxen/netxen_nic_ethtool.c +++ b/drivers/net/netxen/netxen_nic_ethtool.c @@ -871,7 +871,7 @@ static int netxen_nic_set_flags(struct net_device *netdev, u32 data) struct netxen_adapter *adapter = netdev_priv(netdev); int hw_lro; - if (data & ~ETH_FLAG_LRO) + if (ethtool_invalid_flags(netdev, data, ETH_FLAG_LRO)) return -EINVAL; if (!(adapter->capabilities & NX_FW_CAPABILITY_HW_LRO)) diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index 993c52c82aeb..e870c0698bbe 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -442,11 +442,11 @@ static int phy_attach_direct(struct net_device *dev, struct phy_device *phydev, u32 flags, phy_interface_t interface) { struct device *d = &phydev->dev; + int err; /* Assume that if there is no driver, that it doesn't * exist, and we should use the genphy driver. */ if (NULL == d->driver) { - int err; d->driver = &genphy_driver.driver; err = d->driver->probe(d); @@ -474,7 +474,11 @@ static int phy_attach_direct(struct net_device *dev, struct phy_device *phydev, /* Do initial configuration here, now that * we have certain key parameters * (dev_flags and interface) */ - return phy_init_hw(phydev); + err = phy_init_hw(phydev); + if (err) + phy_detach(phydev); + + return err; } /** diff --git a/drivers/net/qlcnic/qlcnic_ethtool.c b/drivers/net/qlcnic/qlcnic_ethtool.c index 4c14510e2a87..45b2755d6cba 100644 --- a/drivers/net/qlcnic/qlcnic_ethtool.c +++ b/drivers/net/qlcnic/qlcnic_ethtool.c @@ -1003,7 +1003,7 @@ static int qlcnic_set_flags(struct net_device *netdev, u32 data) struct qlcnic_adapter *adapter = netdev_priv(netdev); int hw_lro; - if (data & ~ETH_FLAG_LRO) + if (ethtool_invalid_flags(netdev, data, ETH_FLAG_LRO)) return -EINVAL; if (!(adapter->capabilities & QLCNIC_FW_CAPABILITY_HW_LRO)) diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index 2ad6364103ea..356e74d20b80 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -6726,7 +6726,7 @@ static int s2io_ethtool_set_flags(struct net_device *dev, u32 data) int rc = 0; int changed = 0; - if (data & ~ETH_FLAG_LRO) + if (ethtool_invalid_flags(dev, data, ETH_FLAG_LRO)) return -EINVAL; if (data & ETH_FLAG_LRO) { diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index ebec88882c3b..73c942d85f07 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -48,9 +48,9 @@ #include <net/ip.h> #include <asm/system.h> -#include <asm/io.h> +#include <linux/io.h> #include <asm/byteorder.h> -#include <asm/uaccess.h> +#include <linux/uaccess.h> #ifdef CONFIG_SPARC #include <asm/idprom.h> @@ -13118,7 +13118,7 @@ done: static struct pci_dev * __devinit tg3_find_peer(struct tg3 *); -static void inline vlan_features_add(struct net_device *dev, unsigned long flags) +static inline void vlan_features_add(struct net_device *dev, unsigned long flags) { dev->vlan_features |= flags; } diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig index 6f600cced6e1..3ec22c307797 100644 --- a/drivers/net/usb/Kconfig +++ b/drivers/net/usb/Kconfig @@ -433,4 +433,19 @@ config USB_SIERRA_NET To compile this driver as a module, choose M here: the module will be called sierra_net. +config USB_VL600 + tristate "LG VL600 modem dongle" + depends on USB_NET_CDCETHER + select USB_ACM + help + Select this if you want to use an LG Electronics 4G/LTE usb modem + called VL600. This driver only handles the ethernet + interface exposed by the modem firmware. To establish a connection + you will first need a userspace program that sends the right + command to the modem through its CDC ACM port, and most + likely also a DHCP client. See this thread about using the + 4G modem from Verizon: + + http://ubuntuforums.org/showpost.php?p=10589647&postcount=17 + endmenu diff --git a/drivers/net/usb/Makefile b/drivers/net/usb/Makefile index cac170301187..c7ec8a5f0a90 100644 --- a/drivers/net/usb/Makefile +++ b/drivers/net/usb/Makefile @@ -27,4 +27,5 @@ obj-$(CONFIG_USB_IPHETH) += ipheth.o obj-$(CONFIG_USB_SIERRA_NET) += sierra_net.o obj-$(CONFIG_USB_NET_CX82310_ETH) += cx82310_eth.o obj-$(CONFIG_USB_NET_CDC_NCM) += cdc_ncm.o +obj-$(CONFIG_USB_VL600) += lg-vl600.o diff --git a/drivers/net/usb/cdc_ether.c b/drivers/net/usb/cdc_ether.c index 9a60e415d76b..51c259b69278 100644 --- a/drivers/net/usb/cdc_ether.c +++ b/drivers/net/usb/cdc_ether.c @@ -378,7 +378,7 @@ static void dumpspeed(struct usbnet *dev, __le32 *speeds) __le32_to_cpu(speeds[1]) / 1000); } -static void cdc_status(struct usbnet *dev, struct urb *urb) +void usbnet_cdc_status(struct usbnet *dev, struct urb *urb) { struct usb_cdc_notification *event; @@ -418,8 +418,9 @@ static void cdc_status(struct usbnet *dev, struct urb *urb) break; } } +EXPORT_SYMBOL_GPL(usbnet_cdc_status); -static int cdc_bind(struct usbnet *dev, struct usb_interface *intf) +int usbnet_cdc_bind(struct usbnet *dev, struct usb_interface *intf) { int status; struct cdc_state *info = (void *) &dev->data; @@ -441,6 +442,7 @@ static int cdc_bind(struct usbnet *dev, struct usb_interface *intf) */ return 0; } +EXPORT_SYMBOL_GPL(usbnet_cdc_bind); static int cdc_manage_power(struct usbnet *dev, int on) { @@ -452,18 +454,18 @@ static const struct driver_info cdc_info = { .description = "CDC Ethernet Device", .flags = FLAG_ETHER, // .check_connect = cdc_check_connect, - .bind = cdc_bind, + .bind = usbnet_cdc_bind, .unbind = usbnet_cdc_unbind, - .status = cdc_status, + .status = usbnet_cdc_status, .manage_power = cdc_manage_power, }; static const struct driver_info mbm_info = { .description = "Mobile Broadband Network Device", .flags = FLAG_WWAN, - .bind = cdc_bind, + .bind = usbnet_cdc_bind, .unbind = usbnet_cdc_unbind, - .status = cdc_status, + .status = usbnet_cdc_status, .manage_power = cdc_manage_power, }; @@ -560,6 +562,13 @@ static const struct usb_device_id products [] = { .driver_info = 0, }, +/* LG Electronics VL600 wants additional headers on every frame */ +{ + USB_DEVICE_AND_INTERFACE_INFO(0x1004, 0x61aa, USB_CLASS_COMM, + USB_CDC_SUBCLASS_ETHERNET, USB_CDC_PROTO_NONE), + .driver_info = 0, +}, + /* * WHITELIST!!! * diff --git a/drivers/net/usb/lg-vl600.c b/drivers/net/usb/lg-vl600.c new file mode 100644 index 000000000000..1d83ccfd7277 --- /dev/null +++ b/drivers/net/usb/lg-vl600.c @@ -0,0 +1,346 @@ +/* + * Ethernet interface part of the LG VL600 LTE modem (4G dongle) + * + * Copyright (C) 2011 Intel Corporation + * Author: Andrzej Zaborowski <balrogg@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#include <linux/etherdevice.h> +#include <linux/ethtool.h> +#include <linux/mii.h> +#include <linux/usb.h> +#include <linux/usb/cdc.h> +#include <linux/usb/usbnet.h> +#include <linux/if_ether.h> +#include <linux/if_arp.h> +#include <linux/inetdevice.h> + +/* + * The device has a CDC ACM port for modem control (it claims to be + * CDC ACM anyway) and a CDC Ethernet port for actual network data. + * It will however ignore data on both ports that is not encapsulated + * in a specific way, any data returned is also encapsulated the same + * way. The headers don't seem to follow any popular standard. + * + * This driver adds and strips these headers from the ethernet frames + * sent/received from the CDC Ethernet port. The proprietary header + * replaces the standard ethernet header in a packet so only actual + * ethernet frames are allowed. The headers allow some form of + * multiplexing by using non standard values of the .h_proto field. + * Windows/Mac drivers do send a couple of such frames to the device + * during initialisation, with protocol set to 0x0906 or 0x0b06 and (what + * seems to be) a flag in the .dummy_flags. This doesn't seem necessary + * for modem operation but can possibly be used for GPS or other funcitons. + */ + +struct vl600_frame_hdr { + __le32 len; + __le32 serial; + __le32 pkt_cnt; + __le32 dummy_flags; + __le32 dummy; + __le32 magic; +} __attribute__((packed)); + +struct vl600_pkt_hdr { + __le32 dummy[2]; + __le32 len; + __be16 h_proto; +} __attribute__((packed)); + +struct vl600_state { + struct sk_buff *current_rx_buf; +}; + +static int vl600_bind(struct usbnet *dev, struct usb_interface *intf) +{ + int ret; + struct vl600_state *s = kzalloc(sizeof(struct vl600_state), GFP_KERNEL); + + if (!s) + return -ENOMEM; + + ret = usbnet_cdc_bind(dev, intf); + if (ret) { + kfree(s); + return ret; + } + + dev->driver_priv = s; + + /* ARP packets don't go through, but they're also of no use. The + * subnet has only two hosts anyway: us and the gateway / DHCP + * server (probably simulated by modem firmware or network operator) + * whose address changes everytime we connect to the intarwebz and + * who doesn't bother answering ARP requests either. So hardware + * addresses have no meaning, the destination and the source of every + * packet depend only on whether it is on the IN or OUT endpoint. */ + dev->net->flags |= IFF_NOARP; + + return ret; +} + +static void vl600_unbind(struct usbnet *dev, struct usb_interface *intf) +{ + struct vl600_state *s = dev->driver_priv; + + if (s->current_rx_buf) + dev_kfree_skb(s->current_rx_buf); + + kfree(s); + + return usbnet_cdc_unbind(dev, intf); +} + +static int vl600_rx_fixup(struct usbnet *dev, struct sk_buff *skb) +{ + struct vl600_frame_hdr *frame; + struct vl600_pkt_hdr *packet; + struct ethhdr *ethhdr; + int packet_len, count; + struct sk_buff *buf = skb; + struct sk_buff *clone; + struct vl600_state *s = dev->driver_priv; + + /* Frame lengths are generally 4B multiplies but every couple of + * hours there's an odd number of bytes sized yet correct frame, + * so don't require this. */ + + /* Allow a packet (or multiple packets batched together) to be + * split across many frames. We don't allow a new batch to + * begin in the same frame another one is ending however, and no + * leading or trailing pad bytes. */ + if (s->current_rx_buf) { + frame = (struct vl600_frame_hdr *) s->current_rx_buf->data; + if (skb->len + s->current_rx_buf->len > + le32_to_cpup(&frame->len)) { + netif_err(dev, ifup, dev->net, "Fragment too long\n"); + dev->net->stats.rx_length_errors++; + goto error; + } + + buf = s->current_rx_buf; + memcpy(skb_put(buf, skb->len), skb->data, skb->len); + } else if (skb->len < 4) { + netif_err(dev, ifup, dev->net, "Frame too short\n"); + dev->net->stats.rx_length_errors++; + goto error; + } + + frame = (struct vl600_frame_hdr *) buf->data; + /* NOTE: Should check that frame->magic == 0x53544448? + * Otherwise if we receive garbage at the beginning of the frame + * we may end up allocating a huge buffer and saving all the + * future incoming data into it. */ + + if (buf->len < sizeof(*frame) || + buf->len != le32_to_cpup(&frame->len)) { + /* Save this fragment for later assembly */ + if (s->current_rx_buf) + return 0; + + s->current_rx_buf = skb_copy_expand(skb, 0, + le32_to_cpup(&frame->len), GFP_ATOMIC); + if (!s->current_rx_buf) { + netif_err(dev, ifup, dev->net, "Reserving %i bytes " + "for packet assembly failed.\n", + le32_to_cpup(&frame->len)); + dev->net->stats.rx_errors++; + } + + return 0; + } + + count = le32_to_cpup(&frame->pkt_cnt); + + skb_pull(buf, sizeof(*frame)); + + while (count--) { + if (buf->len < sizeof(*packet)) { + netif_err(dev, ifup, dev->net, "Packet too short\n"); + goto error; + } + + packet = (struct vl600_pkt_hdr *) buf->data; + packet_len = sizeof(*packet) + le32_to_cpup(&packet->len); + if (packet_len > buf->len) { + netif_err(dev, ifup, dev->net, + "Bad packet length stored in header\n"); + goto error; + } + + /* Packet header is same size as the ethernet header + * (sizeof(*packet) == sizeof(*ethhdr)), additionally + * the h_proto field is in the same place so we just leave it + * alone and fill in the remaining fields. + */ + ethhdr = (struct ethhdr *) skb->data; + if (be16_to_cpup(ðhdr->h_proto) == ETH_P_ARP && + buf->len > 0x26) { + /* Copy the addresses from packet contents */ + memcpy(ethhdr->h_source, + &buf->data[sizeof(*ethhdr) + 0x8], + ETH_ALEN); + memcpy(ethhdr->h_dest, + &buf->data[sizeof(*ethhdr) + 0x12], + ETH_ALEN); + } else { + memset(ethhdr->h_source, 0, ETH_ALEN); + memcpy(ethhdr->h_dest, dev->net->dev_addr, ETH_ALEN); + } + + if (count) { + /* Not the last packet in this batch */ + clone = skb_clone(buf, GFP_ATOMIC); + if (!clone) + goto error; + + skb_trim(clone, packet_len); + usbnet_skb_return(dev, clone); + + skb_pull(buf, (packet_len + 3) & ~3); + } else { + skb_trim(buf, packet_len); + + if (s->current_rx_buf) { + usbnet_skb_return(dev, buf); + s->current_rx_buf = NULL; + return 0; + } + + return 1; + } + } + +error: + if (s->current_rx_buf) { + dev_kfree_skb_any(s->current_rx_buf); + s->current_rx_buf = NULL; + } + dev->net->stats.rx_errors++; + return 0; +} + +static struct sk_buff *vl600_tx_fixup(struct usbnet *dev, + struct sk_buff *skb, gfp_t flags) +{ + struct sk_buff *ret; + struct vl600_frame_hdr *frame; + struct vl600_pkt_hdr *packet; + static uint32_t serial = 1; + int orig_len = skb->len - sizeof(struct ethhdr); + int full_len = (skb->len + sizeof(struct vl600_frame_hdr) + 3) & ~3; + + frame = (struct vl600_frame_hdr *) skb->data; + if (skb->len > sizeof(*frame) && skb->len == le32_to_cpup(&frame->len)) + return skb; /* Already encapsulated? */ + + if (skb->len < sizeof(struct ethhdr)) + /* Drop, device can only deal with ethernet packets */ + return NULL; + + if (!skb_cloned(skb)) { + int headroom = skb_headroom(skb); + int tailroom = skb_tailroom(skb); + + if (tailroom >= full_len - skb->len - sizeof(*frame) && + headroom >= sizeof(*frame)) + /* There's enough head and tail room */ + goto encapsulate; + + if (headroom + tailroom + skb->len >= full_len) { + /* There's enough total room, just readjust */ + skb->data = memmove(skb->head + sizeof(*frame), + skb->data, skb->len); + skb_set_tail_pointer(skb, skb->len); + goto encapsulate; + } + } + + /* Alloc a new skb with the required size */ + ret = skb_copy_expand(skb, sizeof(struct vl600_frame_hdr), full_len - + skb->len - sizeof(struct vl600_frame_hdr), flags); + dev_kfree_skb_any(skb); + if (!ret) + return ret; + skb = ret; + +encapsulate: + /* Packet header is same size as ethernet packet header + * (sizeof(*packet) == sizeof(struct ethhdr)), additionally the + * h_proto field is in the same place so we just leave it alone and + * overwrite the remaining fields. + */ + packet = (struct vl600_pkt_hdr *) skb->data; + memset(&packet->dummy, 0, sizeof(packet->dummy)); + packet->len = cpu_to_le32(orig_len); + + frame = (struct vl600_frame_hdr *) skb_push(skb, sizeof(*frame)); + memset(frame, 0, sizeof(*frame)); + frame->len = cpu_to_le32(full_len); + frame->serial = cpu_to_le32(serial++); + frame->pkt_cnt = cpu_to_le32(1); + + if (skb->len < full_len) /* Pad */ + skb_put(skb, full_len - skb->len); + + return skb; +} + +static const struct driver_info vl600_info = { + .description = "LG VL600 modem", + .flags = FLAG_ETHER | FLAG_RX_ASSEMBLE, + .bind = vl600_bind, + .unbind = vl600_unbind, + .status = usbnet_cdc_status, + .rx_fixup = vl600_rx_fixup, + .tx_fixup = vl600_tx_fixup, +}; + +static const struct usb_device_id products[] = { + { + USB_DEVICE_AND_INTERFACE_INFO(0x1004, 0x61aa, USB_CLASS_COMM, + USB_CDC_SUBCLASS_ETHERNET, USB_CDC_PROTO_NONE), + .driver_info = (unsigned long) &vl600_info, + }, + {}, /* End */ +}; +MODULE_DEVICE_TABLE(usb, products); + +static struct usb_driver lg_vl600_driver = { + .name = "lg-vl600", + .id_table = products, + .probe = usbnet_probe, + .disconnect = usbnet_disconnect, + .suspend = usbnet_suspend, + .resume = usbnet_resume, +}; + +static int __init vl600_init(void) +{ + return usb_register(&lg_vl600_driver); +} +module_init(vl600_init); + +static void __exit vl600_exit(void) +{ + usb_deregister(&lg_vl600_driver); +} +module_exit(vl600_exit); + +MODULE_AUTHOR("Anrzej Zaborowski"); +MODULE_DESCRIPTION("LG-VL600 modem's ethernet link"); +MODULE_LICENSE("GPL"); diff --git a/drivers/net/usb/usbnet.c b/drivers/net/usb/usbnet.c index 95c41d56631c..cf58b7682565 100644 --- a/drivers/net/usb/usbnet.c +++ b/drivers/net/usb/usbnet.c @@ -387,8 +387,12 @@ static int rx_submit (struct usbnet *dev, struct urb *urb, gfp_t flags) static inline void rx_process (struct usbnet *dev, struct sk_buff *skb) { if (dev->driver_info->rx_fixup && - !dev->driver_info->rx_fixup (dev, skb)) - goto error; + !dev->driver_info->rx_fixup (dev, skb)) { + /* With RX_ASSEMBLE, rx_fixup() must update counters */ + if (!(dev->driver_info->flags & FLAG_RX_ASSEMBLE)) + dev->net->stats.rx_errors++; + goto done; + } // else network stack removes extra byte if we forced a short packet if (skb->len) { @@ -401,8 +405,8 @@ static inline void rx_process (struct usbnet *dev, struct sk_buff *skb) } netif_dbg(dev, rx_err, dev->net, "drop\n"); -error: dev->net->stats.rx_errors++; +done: skb_queue_tail(&dev->done, skb); } diff --git a/drivers/net/vmxnet3/vmxnet3_ethtool.c b/drivers/net/vmxnet3/vmxnet3_ethtool.c index 81254be85b92..51f2ef142a5b 100644 --- a/drivers/net/vmxnet3/vmxnet3_ethtool.c +++ b/drivers/net/vmxnet3/vmxnet3_ethtool.c @@ -304,8 +304,8 @@ vmxnet3_set_flags(struct net_device *netdev, u32 data) u8 lro_present = (netdev->features & NETIF_F_LRO) == 0 ? 0 : 1; unsigned long flags; - if (data & ~ETH_FLAG_LRO) - return -EOPNOTSUPP; + if (ethtool_invalid_flags(netdev, data, ETH_FLAG_LRO)) + return -EINVAL; if (lro_requested ^ lro_present) { /* toggle the LRO feature*/ diff --git a/drivers/net/vxge/vxge-ethtool.c b/drivers/net/vxge/vxge-ethtool.c index 1dd3a21b3a43..c5eb034107fd 100644 --- a/drivers/net/vxge/vxge-ethtool.c +++ b/drivers/net/vxge/vxge-ethtool.c @@ -1117,8 +1117,8 @@ static int vxge_set_flags(struct net_device *dev, u32 data) struct vxgedev *vdev = netdev_priv(dev); enum vxge_hw_status status; - if (data & ~ETH_FLAG_RXHASH) - return -EOPNOTSUPP; + if (ethtool_invalid_flags(dev, data, ETH_FLAG_RXHASH)) + return -EINVAL; if (!!(data & ETH_FLAG_RXHASH) == vdev->devh->config.rth_en) return 0; diff --git a/drivers/net/wireless/p54/p54spi.c b/drivers/net/wireless/p54/p54spi.c index 18d24b7b1e34..7ecc0bda57b3 100644 --- a/drivers/net/wireless/p54/p54spi.c +++ b/drivers/net/wireless/p54/p54spi.c @@ -649,8 +649,7 @@ static int __devinit p54spi_probe(struct spi_device *spi) goto err_free_common; } - set_irq_type(gpio_to_irq(p54spi_gpio_irq), - IRQ_TYPE_EDGE_RISING); + irq_set_irq_type(gpio_to_irq(p54spi_gpio_irq), IRQ_TYPE_EDGE_RISING); disable_irq(gpio_to_irq(p54spi_gpio_irq)); diff --git a/drivers/net/wireless/wl1251/sdio.c b/drivers/net/wireless/wl1251/sdio.c index d550b5e68d3c..f51a0241a440 100644 --- a/drivers/net/wireless/wl1251/sdio.c +++ b/drivers/net/wireless/wl1251/sdio.c @@ -265,7 +265,7 @@ static int wl1251_sdio_probe(struct sdio_func *func, goto disable; } - set_irq_type(wl->irq, IRQ_TYPE_EDGE_RISING); + irq_set_irq_type(wl->irq, IRQ_TYPE_EDGE_RISING); disable_irq(wl->irq); wl1251_sdio_ops.enable_irq = wl1251_enable_line_irq; diff --git a/drivers/net/wireless/wl1251/spi.c b/drivers/net/wireless/wl1251/spi.c index ac872b38960f..af6448c4d3e2 100644 --- a/drivers/net/wireless/wl1251/spi.c +++ b/drivers/net/wireless/wl1251/spi.c @@ -286,7 +286,7 @@ static int __devinit wl1251_spi_probe(struct spi_device *spi) goto out_free; } - set_irq_type(wl->irq, IRQ_TYPE_EDGE_RISING); + irq_set_irq_type(wl->irq, IRQ_TYPE_EDGE_RISING); disable_irq(wl->irq); |