diff options
Diffstat (limited to 'Platforms/Hisilicon/DeviceTree/hi6220-hikey.dts')
| -rw-r--r-- | Platforms/Hisilicon/DeviceTree/hi6220-hikey.dts | 548 |
1 files changed, 548 insertions, 0 deletions
diff --git a/Platforms/Hisilicon/DeviceTree/hi6220-hikey.dts b/Platforms/Hisilicon/DeviceTree/hi6220-hikey.dts new file mode 100644 index 0000000..e94fa1a --- /dev/null +++ b/Platforms/Hisilicon/DeviceTree/hi6220-hikey.dts @@ -0,0 +1,548 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * dts file for Hisilicon HiKey Development Board + * + * Copyright (C) 2015, Hisilicon Ltd. + * + */ + +/dts-v1/; +#include "hi6220.dtsi" +#include "hikey-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "HiKey Development Board"; + compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; + + aliases { + serial0 = &uart0; /* On board UART0 */ + serial1 = &uart1; /* BT UART */ + serial2 = &uart2; /* LS Expansion UART0 */ + serial3 = &uart3; /* LS Expansion UART1 */ + }; + + chosen { + stdout-path = "serial3:115200n8"; + }; + + /* + * Reserve below regions from memory node: + * + * 0x05e0,0000 - 0x05ef,ffff: MCU firmware runtime using + * 0x05f0,1000 - 0x05f0,1fff: Reboot reason + * 0x06df,f000 - 0x06df,ffff: Mailbox message data + * 0x0740,f000 - 0x0740,ffff: MCU firmware section + * 0x21f0,0000 - 0x21ff,ffff: pstore/ramoops buffer + * 0x3e00,0000 - 0x3fff,ffff: OP-TEE + */ + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x00000000 0x00000000 0x05e00000>, + <0x00000000 0x05f00000 0x00000000 0x00001000>, + <0x00000000 0x05f02000 0x00000000 0x00efd000>, + <0x00000000 0x06e00000 0x00000000 0x0060f000>, + <0x00000000 0x07410000 0x00000000 0x1aaf0000>, + <0x00000000 0x22000000 0x00000000 0x1c000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ramoops@0x21f00000 { + compatible = "ramoops"; + reg = <0x0 0x21f00000 0x0 0x00100000>; + record-size = <0x00020000>; + console-size = <0x00020000>; + ftrace-size = <0x00020000>; + }; + + /* global autoconfigured region for contiguous allocations */ + linux,cma { + compatible = "shared-dma-pool"; + reusable; + size = <0x00000000 0x08000000>; + linux,cma-default; + }; + }; + + reboot-mode-syscon@5f01000 { + compatible = "syscon", "simple-mfd"; + reg = <0x0 0x05f01000 0x0 0x00001000>; + + reboot-mode { + compatible = "syscon-reboot-mode"; + offset = <0x0>; + + mode-normal = <0x77665501>; + mode-bootloader = <0x77665500>; + mode-recovery = <0x77665502>; + }; + }; + + reg_sys_5v: regulator@0 { + compatible = "regulator-fixed"; + regulator-name = "SYS_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdd_3v3: regulator@1 { + compatible = "regulator-fixed"; + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <®_sys_5v>; + }; + + reg_5v_hub: regulator@2 { + compatible = "regulator-fixed"; + regulator-name = "5V_HUB"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + gpio = <&gpio0 7 0>; + regulator-always-on; + vin-supply = <®_sys_5v>; + }; + + wl1835_pwrseq: wl1835-pwrseq { + compatible = "mmc-pwrseq-simple"; + /* WLAN_EN GPIO */ + reset-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + clocks = <&pmic>; + clock-names = "ext_clock"; + power-off-delay-us = <10>; + }; + + soc { + spi0: spi@f7106000 { + status = "ok"; + }; + + i2c0: i2c@f7100000 { + status = "ok"; + }; + + i2c1: i2c@f7101000 { + status = "ok"; + }; + + uart1: uart@f7111000 { + assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>; + assigned-clock-rates = <150000000>; + status = "ok"; + + bluetooth { + compatible = "ti,wl1835-st"; + enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + clocks = <&pmic>; + clock-names = "ext_clock"; + }; + }; + + uart2: uart@f7112000 { + status = "ok"; + }; + + uart3: uart@f7113000 { + status = "ok"; + }; + + /* + * Legend: proper name = the GPIO line is used as GPIO + * NC = not connected (not routed from the SoC) + * "[PER]" = pin is muxed for peripheral (not GPIO) + * "" = no idea, schematic doesn't say, could be + * unrouted (not connected to any external pin) + * LSEC = Low Speed External Connector + * HSEC = High Speed External Connector + * + * Pin assignments taken from LeMaker and CircuitCo Schematics + * Rev A1. + * + * For the lines routed to the external connectors the + * lines are named after the 96Boards CE Specification 1.0, + * Appendix "Expansion Connector Signal Description". + * + * When the 96Board naming of a line and the schematic name of + * the same line are in conflict, the 96Board specification + * takes precedence, which means that the external UART on the + * LSEC is named UART0 while the schematic and SoC names this + * UART2. This is only for the informational lines i.e. "[FOO]", + * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only + * ones actually used for GPIO. + */ + gpio0: gpio@f8011000 { + gpio-line-names = "PWR_HOLD", "DSI_SEL", + "USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON", + "PWRON_DET", "5V_HUB_EN"; + }; + + gpio1: gpio@f8012000 { + gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N", + "WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON"; + }; + + gpio2: gpio@f8013000 { + gpio-line-names = + "GPIO-A", /* LSEC Pin 23: GPIO2_0 */ + "GPIO-B", /* LSEC Pin 24: GPIO2_1 */ + "GPIO-C", /* LSEC Pin 25: GPIO2_2 */ + "GPIO-D", /* LSEC Pin 26: GPIO2_3 */ + "GPIO-E", /* LSEC Pin 27: GPIO2_4 */ + "USB_ID_DET", "USB_VBUS_DET", + "GPIO-H"; /* LSEC Pin 30: GPIO2_7 */ + }; + + gpio3: gpio@f8014000 { + gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "", + "WLAN_ACTIVE", "NC", "NC"; + }; + + gpio4: gpio@f7020000 { + gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3", + "USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE"; + }; + + gpio5: gpio@f7021000 { + gpio-line-names = "NC", "NC", + "[UART1_RxD]", /* LSEC Pin 11: UART3_RX */ + "[UART1_TxD]", /* LSEC Pin 13: UART3_TX */ + "[AUX_SSI1]", "NC", + "[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */ + "[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */ + }; + + gpio6: gpio@f7022000 { + gpio-line-names = + "[SPI0_DIN]", /* Pin 10: SPI0_DI */ + "[SPI0_DOUT]", /* Pin 14: SPI0_DO */ + "[SPI0_CS]", /* Pin 12: SPI0_CS_N */ + "[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */ + "NC", "NC", "NC", + "GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */ + }; + + gpio7: gpio@f7023000 { + gpio-line-names = "NC", "NC", "NC", "NC", + "[PCM_DI]", /* Pin 22: MODEM_PCM_DI */ + "[PCM_DO]", /* Pin 20: MODEM_PCM_DO */ + "NC", "NC"; + }; + + gpio8: gpio@f7024000 { + gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC", + "", "", "", "", "", ""; + }; + + gpio9: gpio@f7025000 { + gpio-line-names = "", + "GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */ + "GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */ + "NC", "NC", "NC", "NC", "[ISP_CCLK0]"; + }; + + gpio10: gpio@f7026000 { + gpio-line-names = "BOOT_SEL", + "[ISP_CCLK1]", + "GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */ + "GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */ + "NC", "NC", + "[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */ + "[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */ + }; + + gpio11: gpio@f7027000 { + gpio-line-names = + "[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */ + "[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */ + "", "NC", "NC", "NC", "", ""; + }; + + gpio12: gpio@f7028000 { + gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]", + "[BT_PCM_DO]", + "NC", "NC", "NC", "NC", + "GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */ + }; + + gpio13: gpio@f7029000 { + gpio-line-names = "[UART0_RX]", "[UART0_TX]", + "[BT_UART1_CTS]", "[BT_UART1_RTS]", + "[BT_UART1_RX]", "[BT_UART1_TX]", + "[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */ + "[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */ + }; + + gpio14: gpio@f702a000 { + gpio-line-names = + "[UART0_RxD]", /* LSEC Pin 7: UART2_RX */ + "[UART0_TxD]", /* LSEC Pin 5: UART2_TX */ + "[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */ + "[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */ + "[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */ + "[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */ + "[I2C2_SCL]", "[I2C2_SDA]"; + }; + + gpio15: gpio@f702b000 { + gpio-line-names = "", "", "", "", "", "", "NC", ""; + }; + + /* GPIO blocks 16 thru 19 do not appear to be routed to pins */ + + dwmmc_0: dwmmc0@f723d000 { + cap-mmc-highspeed; + non-removable; + bus-width = <0x8>; + vmmc-supply = <&ldo19>; + }; + + dwmmc_1: dwmmc1@f723e000 { + card-detect-delay = <200>; + cap-sd-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + vqmmc-supply = <&ldo7>; + vmmc-supply = <&ldo10>; + bus-width = <0x4>; + disable-wp; + cd-gpios = <&gpio1 0 1>; + }; + + dwmmc_2: dwmmc2@f723f000 { + bus-width = <0x4>; + non-removable; + vmmc-supply = <®_vdd_3v3>; + mmc-pwrseq = <&wl1835_pwrseq>; + + #address-cells = <0x1>; + #size-cells = <0x0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; /* sdio func num */ + /* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */ + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_EDGE_RISING>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + user_led4 { + label = "user_led4"; + gpios = <&gpio4 0 0>; /* <&gpio_user_led_1>; */ + linux,default-trigger = "heartbeat"; + }; + + user_led3 { + label = "user_led3"; + gpios = <&gpio4 1 0>; /* <&gpio_user_led_2>; */ + linux,default-trigger = "mmc0"; + }; + + user_led2 { + label = "user_led2"; + gpios = <&gpio4 2 0>; /* <&gpio_user_led_3>; */ + linux,default-trigger = "mmc1"; + }; + + user_led1 { + label = "user_led1"; + gpios = <&gpio4 3 0>; /* <&gpio_user_led_4>; */ + panic-indicator; + linux,default-trigger = "cpu0"; + }; + + wlan_active_led { + label = "wifi_active"; + gpios = <&gpio3 5 0>; /* <&gpio_wlan_active_led>; */ + linux,default-trigger = "phy0tx"; + default-state = "off"; + }; + + bt_active_led { + label = "bt_active"; + gpios = <&gpio4 7 0>; /* <&gpio_bt_active_led>; */ + linux,default-trigger = "hci0rx"; + default-state = "off"; + }; + }; + + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + reg = <0x0 0xf8000000 0x0 0x1000>; + #clock-cells = <0>; + interrupt-controller; + #interrupt-cells = <2>; + pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + + regulators { + ldo2: LDO2 { + regulator-name = "LDO2_2V8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + + ldo7: LDO7 { + regulator-name = "LDO7_SDIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <120>; + }; + + ldo10: LDO10 { + regulator-name = "LDO10_2V85"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <360>; + }; + + ldo13: LDO13 { + regulator-name = "LDO13_1V8"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <1950000>; + regulator-enable-ramp-delay = <120>; + }; + + ldo14: LDO14 { + regulator-name = "LDO14_2V8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + + ldo15: LDO15 { + regulator-name = "LDO15_1V8"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <1950000>; + regulator-boot-on; + regulator-always-on; + regulator-enable-ramp-delay = <120>; + }; + + ldo17: LDO17 { + regulator-name = "LDO17_2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + + ldo19: LDO19 { + regulator-name = "LDO19_3V0"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <360>; + }; + + ldo21: LDO21 { + regulator-name = "LDO21_1V8"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + regulator-enable-ramp-delay = <120>; + }; + + ldo22: LDO22 { + regulator-name = "LDO22_1V2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + regulator-enable-ramp-delay = <120>; + }; + }; + }; + + firmware { + optee { + compatible = "linaro,optee-tz"; + method = "smc"; + }; + }; + + sound_card { + compatible = "audio-graph-card"; + dais = <&i2s0_port0>; + }; +}; + +&uart2 { + label = "LS-UART0"; +}; +&uart3 { + label = "LS-UART1"; +}; + +&ade { + status = "ok"; +}; + +&dsi { + status = "ok"; + + ports { + /* 1 for output port */ + port@1 { + reg = <1>; + + dsi_out0: endpoint@0 { + remote-endpoint = <&adv7533_in>; + }; + }; + }; +}; + +&i2c2 { + #address-cells = <1>; + #size-cells = <0>; + status = "ok"; + + adv7533: adv7533@39 { + compatible = "adi,adv7533"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <1 2>; + pd-gpio = <&gpio0 4 0>; + adi,dsi-lanes = <4>; + #sound-dai-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + adv7533_in: endpoint { + remote-endpoint = <&dsi_out0>; + }; + }; + port@2 { + reg = <2>; + codec_endpoint: endpoint { + remote-endpoint = <&i2s0_cpu_endpoint>; + }; + }; + }; + }; +}; + +&i2s0 { + + ports { + i2s0_port0: port@0 { + i2s0_cpu_endpoint: endpoint { + remote-endpoint = <&codec_endpoint>; + dai-format = "i2s"; + }; + }; + }; +}; |