From 14809b6c21c89dd65abaf3fea7627fb5ea0f78a3 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 15 Oct 2009 17:47:13 +0400 Subject: mpc85xx: Configure QE UART for MPC8569E-MDS boards To make QE UART usable by Linux we should setup pin multiplexing and turn UCC2 Ethernet node into UCC2 QE UART node. Also, QE UART is mutually exclusive with UART0, so we can't enable it if eSDHC is in 4-bits mode on pilot boards, or if it's a prototype board with eSDHC in 1- or 4-bits mode. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- board/freescale/mpc8569mds/bcsr.h | 1 + board/freescale/mpc8569mds/mpc8569mds.c | 98 ++++++++++++++++++++++++++------- 2 files changed, 78 insertions(+), 21 deletions(-) (limited to 'board') diff --git a/board/freescale/mpc8569mds/bcsr.h b/board/freescale/mpc8569mds/bcsr.h index 2ed57d8527..179a54c257 100644 --- a/board/freescale/mpc8569mds/bcsr.h +++ b/board/freescale/mpc8569mds/bcsr.h @@ -68,6 +68,7 @@ #define BCSR15_SMII6_DIS 0x08 #define BCSR15_SMII8_DIS 0x04 +#define BCSR15_QEUART_EN 0x01 #define BCSR16_UPC1_DEV2 0x02 diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c index 7d1d02e7d2..ef99a751fd 100644 --- a/board/freescale/mpc8569mds/mpc8569mds.c +++ b/board/freescale/mpc8569mds/mpc8569mds.c @@ -154,6 +154,12 @@ const qe_iop_conf_t qe_iop_conf_tab[] = { {5, 10, 2, 0, 3}, /* UART1_CTS_B */ {5, 11, 1, 0, 2}, /* UART1_RTS_B */ + /* QE UART */ + {0, 19, 1, 0, 2}, /* QEUART_TX */ + {1, 17, 2, 0, 3}, /* QEUART_RX */ + {0, 25, 1, 0, 1}, /* QEUART_RTS */ + {1, 23, 2, 0, 1}, /* QEUART_CTS */ + /* SPI Flash, M25P40 */ {4, 27, 3, 0, 1}, /* SPI_MOSI */ {4, 28, 3, 0, 1}, /* SPI_MISO */ @@ -311,7 +317,26 @@ local_bus_init(void) out_be32(&lbc->lcrr, (u32)in_be32(&lbc->lcrr)| 0x00030000); } -#ifdef CONFIG_FSL_ESDHC +static void fdt_board_disable_serial(void *blob, bd_t *bd, const char *alias) +{ + const char *status = "disabled"; + int off; + int err; + + off = fdt_path_offset(blob, alias); + if (off < 0) { + printf("WARNING: could not find %s alias: %s.\n", alias, + fdt_strerror(off)); + return; + } + + err = fdt_setprop(blob, off, "status", status, strlen(status) + 1); + if (err) { + printf("WARNING: could not set status for serial0: %s.\n", + fdt_strerror(err)); + return; + } +} /* * Because of an erratum in prototype boards it is impossible to use eSDHC @@ -337,6 +362,53 @@ static int esdhc_disables_uart0(void) hwconfig_subarg_cmp("esdhc", "mode", "4-bits"); } +static void fdt_board_fixup_qe_uart(void *blob, bd_t *bd) +{ + u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE; + const char *devtype = "serial"; + const char *compat = "ucc_uart"; + const char *clk = "brg9"; + u32 portnum = 0; + int off = -1; + + if (!hwconfig("qe_uart")) + return; + + if (hwconfig("esdhc") && esdhc_disables_uart0()) { + printf("QE UART: won't enable with esdhc.\n"); + return; + } + + fdt_board_disable_serial(blob, bd, "serial1"); + + while (1) { + const u32 *idx; + int len; + + off = fdt_node_offset_by_compatible(blob, off, "ucc_geth"); + if (off < 0) { + printf("WARNING: unable to fixup device tree for " + "QE UART\n"); + return; + } + + idx = fdt_getprop(blob, off, "cell-index", &len); + if (!idx || len != sizeof(*idx) || *idx != fdt32_to_cpu(2)) + continue; + break; + } + + fdt_setprop(blob, off, "device_type", devtype, strlen(devtype) + 1); + fdt_setprop(blob, off, "compatible", compat, strlen(compat) + 1); + fdt_setprop(blob, off, "tx-clock-name", clk, strlen(clk) + 1); + fdt_setprop(blob, off, "rx-clock-name", clk, strlen(clk) + 1); + fdt_setprop(blob, off, "port-number", &portnum, sizeof(portnum)); + + setbits_8(&bcsr[15], BCSR15_QEUART_EN); +} + +#ifdef CONFIG_FSL_ESDHC + int board_mmc_init(bd_t *bd) { struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_MPC85xx_GUTS_ADDR; @@ -376,31 +448,14 @@ int board_mmc_init(bd_t *bd) static void fdt_board_fixup_esdhc(void *blob, bd_t *bd) { const char *status = "disabled"; - int off; - int err; + int off = -1; if (!hwconfig("esdhc")) return; - if (!esdhc_disables_uart0()) - goto disable_i2c2; - - off = fdt_path_offset(blob, "serial0"); - if (off < 0) { - printf("WARNING: could not find serial0 alias: %s.\n", - fdt_strerror(off)); - goto disable_i2c2; - } - - err = fdt_setprop(blob, off, "status", status, strlen(status) + 1); - if (err) { - printf("WARNING: could not set status for serial0: %s.\n", - fdt_strerror(err)); - return; - } + if (esdhc_disables_uart0()) + fdt_board_disable_serial(blob, bd, "serial0"); -disable_i2c2: - off = -1; while (1) { const u32 *idx; int len; @@ -566,5 +621,6 @@ void ft_board_setup(void *blob, bd_t *bd) ft_fsl_pci_setup(blob, "pci1", &pcie1_hose); #endif fdt_board_fixup_esdhc(blob, bd); + fdt_board_fixup_qe_uart(blob, bd); } #endif -- cgit v1.2.3